Precor 5.33, 5.23 manual Assembly Steps

Page 64

Assembly Steps

Feed the display cable through the upright support.

Important: Do not stretch, crimp, or damage the cable. Cables damaged by improper installation will not be covered by the Precor Limited Warranty.

Attach the display console to the upright support using four Phillips-head screws (A).

Thread the display cable through the grommet and out the front of the base tube. Plug the cable connector into its receptacle.

Important: Important: If the plastic grommet pops out of the base, replace it immediately. The grommet covers the metal edges so the cables are not cut or damaged.

Align the mounting holes and secure the upright support to the base using two hex head screws (D) and two washers

(E). Finger tighten.

Push excess cable into the base tube.

CAUTION: Be aware of a sharp screw inside the base tube. Abrasive cuts or other injuries can occur if you place your hands, fingers, bare feet, or toes inside the base tube.

Lift the EFX. Slide a wedge of packing material under the front of the unit.

EFX5.33 Elliptical Fitness Trainer Assembly Guide

4

Image 64

Contents Page Page Important Safety Instructions Safety Approval Do not use outdoorsGrounding Instructions Units Designated for U.S. MarketsRadio Frequency Interference RFI Federal Communications Commission, PartCanadian Department of Communications Débranchez avant de réparerObtaining Service Table of Contents Precor Residential Equipment EFX Safety Features Locking PinUsing the Stationary Handrail Turning the Unit on and OFF114 GuidelinesUsing SmartRate Exercise to Your Target Heart Rate LEDDisplay Console Page 1532 Scanning and the DisplayCrossRamp Display on the EFX5.23 Keypad QuickstartShows the degree of incline for each CrossRamp setting Changing the Display Features Using the Select Key 1532 132Page Precor Choosing Quickstart User Selecting a User IDSelecting a Program DistCooling Down After a Workout Pausing During a Workout or the Cool-Down Period Ending a WorkoutPrograms Choosing a ProgramTable below shows a variety of program options Program Tips ManlManual Manl Program Xctr Crosstraining Xctr ProgramGlut Hill Gluteal Glut Program Hill Climb Hill ProgramINT1 Interval INTn ProgramRandom Rand Program Weight Loss Wtls Program Rand WtlsFitn Fitness Test FitnGuidelines Warm-up PeriodCompleting the Fitness Test Using the Fitness TestFitness Test Scores Cardiorespiratory Fitness Score Category-Females HRC Heart Rate Control HRC ProgramCST1 Using the HRC ProgramCustom CST1 or CST2 Programs Clearing the Settings on a Custom Program Cals Dist Calories Cals Program Distance Dist ProgramAdvanced Programming and Troubleshooting Advanced Programming TipsRESET, QUICKSTART, ENTER, Select User 2, Crossramp Selecting a U.S. Standard or Metric DisplayInformational Displays Viewing the OdometerViewing the Hour Meter Viewing the Software Version and Part NumbersViewing the Error Log Key DescriptionDisplaying the Serial Number Troubleshooting Error Codes Troubleshooting Heart RateCleaning the Equipment InspectionServicing the EFX Storing the Chest StrapLong-Term Storage Warranty Periods and Coverage Limited WarrantyOptions / Accessories Conditions and Restrictions This limited warranty shall not apply toDisclaimer and Release Exclusive Remedies Exclusion of Consequential and Incidental DamagesThank You and Welcome to Precor Tell US about Your NEW Precor Product Product Specifications EFX5.23/EFX5.33 Elliptical Fitness CrosstrainersPage User ID Keys Locking Pin on the Roller ArmChoose a Program Assembly Guide Obtaining Service Unpacking the Equipment Hardware Kit not shown to scale Fasteners Quantity Assembly Steps EFX5.33 Elliptical Fitness Trainer Assembly Guide EFX5.33 Elliptical Fitness Trainer Assembly Guide EFX5.33 Elliptical Fitness Trainer Assembly Guide Have your assistant carefully lower the unit to the floor