Miele T 7634 Laundry care, Care symbols, Drying tips, Ironing and rotary ironing

Page 10

Laundry care

Care symbols

Drying

￿Normal/higher temperature

￿reduced temperature: select Gentle

(for delicate fabrics)

￿Not suitable for dryer

Ironing and rotary ironing

￿very hot

￿hot

￿not very hot

￿Do not iron/rotary iron

Drying tips

Always check the weight recommendation for maximum loads as listed in the "Program Overview" section.

Overloading will cause wear and tear on the laundry, give a poor drying result and cause more creasing.

Do not dry fabrics that are still soaking wet! After washing, spin fabrics for at least 30 seconds.

Dry mixed loads of cottons, colors and easy-care fabrics in the in the Express program.

Open jackets so that they dry evenly.

Woolens and wool blends tend to mat and shrink. Only handle these fabrics in the Woolens program.

The linings of down-filled garments, depending on quality, tend to shrink. Handle these fabrics only in the Smoothing program.

Pure linens are dried only when indicated on the care label. Otherwise the fabric may become rough. Handle these fabrics only in the Smoothing program.

Cottons (such as T-shirts and underwear) depending on quality, often shrink at the first wash. Therefore: to avoid further shrinkage, do not over-dry these textiles.

Starched laundry may be dried. To achieve the usual finish, however, use a double amount of starch.

Wash new colored fabrics separately before the first drying. Do not dry them together with light-colored fabrics since their colors may run and discolor other garments or even plastic dryer components.

10

Image 10
Contents Operating Instructions Vented dryer 7634 Disposing of your old appliance Caring for the environmentDisposal of packing material Saving energyContents Contents Important Safety Instructions This dryer is intended for residential use only Grounding InstructionsAccessories Control panel Fault indicator / Optical interfaceOperating the dryer DisplayProgram duration/ Estimated time remaining DelayProgrammable functions Drying tips Care symbolsLaundry care DryingLaundry care Preparing the laundry Proper dryingBrief instructions Turn on the dryerSelect program Extra options/Select DelayDryness level selection in programs Before the end of a program Starting the programEnd of program Remove laundry Gentle Options/DelayDelay BuzzerHand iron, Rotary iron Program OverviewNormal Extra dry, Normal Wrinkle-free Extra dry, Normal, Hand ironExpress Normal, Hand iron WoolensSmoothing Dress shirts Normal, Hand ironTimed cold Timed warmLoading or removing laundry Switching over from a running programChanging the program sequence Time remainingActivating the lock Electronic lockDeactivating the lock Cleaning the lint screen without water Cleaning and careCleaning door lint filter Cleaning the lint screen with waterCleaning port-hole grilles Cleaning the dryerTest and fault messages Trouble shootingWhat to do, if . . . ? Cancelling the fault Problem Cause SolutionCancelling a Light goes onOther faults Charged after drying Problem Cause Solution Synthetic-fiber laundryItems are statically There has been a lintCold programs will not Start and the indicatorWhen switched on Lights for these programsReplacing the light bulb Warranty conditions and warranty period Customer serviceProgram updates Optional accessoriesInstallation and connection Front viewCarrying the dryer to the installation site Rear view Installation siteWasher-dryer stack Ventilating the installation area Leveling the dryerElectrical connections General Installing the dryer ventProcedure AvoidCalculating total duct length Arrangement Left or right dryer vent openingAt the rear Rear or side exhaust connectionCalculation example Sideways to left or rightFlexible metal duct hose Overview of vent systemsExamples are shown on the next Examples Dryer vent systems from metal piping ExampleConnecting directly to a wall Side view vent Vent collector duct Washer-dryer stack Technical data Programmable functions for changing Standard values Programmable functions Extending the range of drying levelsBuzzer normal default setting Buzzer loud Adjusting buzzer volumeFor programming and saving in memory, follow steps to Set memory function No Memory default settingMemory Extending cooldown time Default setting Change function of Filter/Vent indicationAdjust keypad tone No Keypad tone default setting Keypad tone onDefault setting Lower conductivity setting Changing water conductivity settingImportant condition Alteration rights reserved Nr 323 240