Miele T 7634 Problem Cause Solution, Light goes on, Cancelling a, Cancelling the fault, Program

Page 24

Trouble shooting

Problem	Cause	Solution
Filter/Vent indicator	The indicator light shows	– As a rule, it is sufficient to
light goes on.	that the dryer is not	clean the lint screens.
	operating at its most	Should that not be
	efficient or economical.	sufficient, then check all
	Possible causes: Blockage	possible causes listed
	by lint or detergent	under "The drying cycle
	residues.	goes on too long or even
		switches off."
		Cancelling test message:
		– Open and close door
	The dryer vent duct may be	– Pay attention to length
	too long, which is not a	and diameter when
	dryer fault.	making duct calculation.
		See "Installing the vent
		duct".
		– Too long a vent duct will
		result in longer program
		times and higher energy
		consumption.
		You can deactivate the
		Filter/Vent indicator lights
		(see section on
		"Programmable functions").
Cancelling a	Possible causes and	Cancelling the fault
program	remedies are described	message:
Filter/Vent indicator	above.	– Open and close door
light goes on.		– Start a program.
The buzzer sounds.		– If the fault message
		comes back, call
		Customer Service.

24

Image 24

Contents Operating Instructions Vented dryer 7634 Caring for the environment Disposal of packing materialDisposing of your old appliance Saving energyContents Contents Important Safety Instructions This dryer is intended for residential use only Grounding InstructionsAccessories Fault indicator / Optical interface Operating the dryerControl panel DisplayDelay Program duration/ Estimated time remainingProgrammable functions Care symbols Laundry careDrying tips DryingLaundry care Proper drying Brief instructionsPreparing the laundry Turn on the dryerExtra options/Select Delay Select programDryness level selection in programs Starting the program Before the end of a programEnd of program Remove laundry Options/Delay DelayGentle BuzzerProgram Overview Normal Extra dry, NormalHand iron, Rotary iron Wrinkle-free Extra dry, Normal, Hand ironWoolens SmoothingExpress Normal, Hand iron Dress shirts Normal, Hand ironTimed cold Timed warmSwitching over from a running program Changing the program sequenceLoading or removing laundry Time remainingElectronic lock Activating the lockDeactivating the lock Cleaning and care Cleaning door lint filterCleaning the lint screen without water Cleaning the lint screen with waterCleaning port-hole grilles Cleaning the dryerTrouble shooting Test and fault messagesWhat to do, if . . . ? Problem Cause Solution Cancelling aCancelling the fault Light goes onOther faults Problem Cause Solution Synthetic-fiber laundry Items are staticallyCharged after drying There has been a lintStart and the indicator When switched onCold programs will not Lights for these programsReplacing the light bulb Customer service Program updatesWarranty conditions and warranty period Optional accessoriesInstallation and connection Front viewRear view Installation site Carrying the dryer to the installation siteWasher-dryer stack Ventilating the installation area Leveling the dryerElectrical connections Installing the dryer vent ProcedureGeneral AvoidCalculating total duct length Arrangement Left or right dryer vent openingRear or side exhaust connection Calculation exampleAt the rear Sideways to left or rightOverview of vent systems Flexible metal duct hoseExamples are shown on the next Examples Dryer vent systems from metal piping ExampleConnecting directly to a wall Side view vent Vent collector duct Washer-dryer stack Technical data Programmable functions for changing Standard values Programmable functions Extending the range of drying levelsAdjusting buzzer volume Buzzer normal default setting Buzzer loudFor programming and saving in memory, follow steps to No Memory default setting Set memory functionMemory Extending cooldown time Default setting Change function of Filter/Vent indicationAdjust keypad tone No Keypad tone default setting Keypad tone onChanging water conductivity setting Default setting Lower conductivity settingImportant condition Alteration rights reserved Nr 323 240