Miele T 7634 operating instructions Other faults

Page 25

 

 

Trouble shooting

 

 

 

 

 

 

Other faults

 

 

 

 

 

Problem

Cause

Solution

The drying

Please check all possible causes and switch the dryer

process goes on

off and then on again.

 

too long or even

Insufficient ventilation,

Open a door or window and

switches off.

perhaps because the

let in increased air flow.

 

Even after the lint

installation space is too

 

screen is cleaned,

small.

 

the Filter/Vent

The door lint filter is blocked

Remove the lint.

indicator come

with lint.

 

on.

 

The vent ducting or its outlet

– Check all components of

 

 

is blocked with lint.

the venting (such as the

 

 

wall pipe, external grill,

 

 

elbows and bends, etc.)

 

 

for unimpeded air flow.

 

 

– Remove the lint.

 

Clothes were insufficiently

In future, spin textiles in the

 

spin-dried.

washer at a higher rpm.

 

The dryer is overloaded.

Verify the maximum load for

 

 

each drying program.

 

Metal components such as

– In future, open the zippers.

 

zippers have prevented the

If the problem recurs, in

 

moisture level of the laundry

future dry garments with long

 

from being determined

zippers using the Timed

 

accurately.

warm program.

The laundry was

The load consisted of various

Re-dry with Timed warm.

not satisfactorily

fabrics.

– Next time, select a suitable

dried.

 

program.

25

Image 25
Contents Operating Instructions Vented dryer 7634 Disposal of packing material Caring for the environmentDisposing of your old appliance Saving energyContents Contents Important Safety Instructions Grounding Instructions This dryer is intended for residential use onlyAccessories Operating the dryer Fault indicator / Optical interfaceControl panel DisplayProgram duration/ Estimated time remaining DelayProgrammable functions Laundry care Care symbolsDrying tips DryingLaundry care Brief instructions Proper dryingPreparing the laundry Turn on the dryerSelect program Extra options/Select DelayDryness level selection in programs Before the end of a program Starting the programEnd of program Remove laundry Delay Options/DelayGentle BuzzerNormal Extra dry, Normal Program OverviewHand iron, Rotary iron Wrinkle-free Extra dry, Normal, Hand ironSmoothing WoolensExpress Normal, Hand iron Dress shirts Normal, Hand ironTimed warm Timed coldChanging the program sequence Switching over from a running programLoading or removing laundry Time remainingActivating the lock Electronic lockDeactivating the lock Cleaning door lint filter Cleaning and careCleaning the lint screen without water Cleaning the lint screen with waterCleaning the dryer Cleaning port-hole grillesTest and fault messages Trouble shootingWhat to do, if . . . ? Cancelling a Problem Cause SolutionCancelling the fault Light goes onOther faults Items are statically Problem Cause Solution Synthetic-fiber laundryCharged after drying There has been a lintWhen switched on Start and the indicatorCold programs will not Lights for these programsReplacing the light bulb Program updates Customer serviceWarranty conditions and warranty period Optional accessoriesFront view Installation and connectionCarrying the dryer to the installation site Rear view Installation siteWasher-dryer stack Leveling the dryer Ventilating the installation areaElectrical connections Procedure Installing the dryer ventGeneral AvoidArrangement Left or right dryer vent opening Calculating total duct lengthCalculation example Rear or side exhaust connectionAt the rear Sideways to left or rightFlexible metal duct hose Overview of vent systemsExamples are shown on the next Examples Example Dryer vent systems from metal pipingConnecting directly to a wall Side view vent Vent collector duct Washer-dryer stack Technical data Programmable functions for changing Standard values Extending the range of drying levels Programmable functionsBuzzer normal default setting Buzzer loud Adjusting buzzer volumeFor programming and saving in memory, follow steps to Set memory function No Memory default settingMemory Extending cooldown time Change function of Filter/Vent indication Default settingNo Keypad tone default setting Keypad tone on Adjust keypad toneDefault setting Lower conductivity setting Changing water conductivity settingImportant condition Alteration rights reserved Nr 323 240