Miele T 7634 operating instructions Extending cooldown time

Page 48

Programmable functions

Extending cooldown time

You can individually lengthen the cooldown phase the occurs before the end of a program. Fabrics will be more completely cooled down.

Cooldown time

–can be extended by two stages.

–it does not function for Smoothing programme.

For programming and saving in memory, follow steps to .

The programmable function is programmed using the buttons.

Precondition:

–The dryer is switched off.

–The door is closed.

Press Start/Stop and keep it pressed it during steps -.

Press the I-On/0-Offbutton in.

Wait until the Start/Stop button lights up continuously . . .

. . . then release the Start/Stop button.

Press the Gentle button three times.

–The Gentle indicator light flashes briefly seven times.

–P and 0 flash alternatingly in the display (default setting).

The number appearing alternatingly with P means:

0Default setting

IFive minutes longer cooldown time (Express indicator light will flash once)

2Ten minutes longer cooldown time (Express indicator light will also flash twice)

Pressing the Start/Stop button switches from one to the other.

Using the I-On/0-Offbutton, switch the dryer off.

The programming is now stored in memory. You can change it again at any time.

48

Image 48

Contents Operating Instructions Vented dryer 7634 Caring for the environment Disposal of packing materialDisposing of your old appliance Saving energyContents Contents Important Safety Instructions This dryer is intended for residential use only Grounding InstructionsAccessories Fault indicator / Optical interface Operating the dryerControl panel DisplayDelay Program duration/ Estimated time remainingProgrammable functions Care symbols Laundry careDrying tips DryingLaundry care Proper drying Brief instructionsPreparing the laundry Turn on the dryerExtra options/Select Delay Select programDryness level selection in programs Starting the program Before the end of a programEnd of program Remove laundry Options/Delay DelayGentle BuzzerProgram Overview Normal Extra dry, NormalHand iron, Rotary iron Wrinkle-free Extra dry, Normal, Hand ironWoolens SmoothingExpress Normal, Hand iron Dress shirts Normal, Hand ironTimed cold Timed warmSwitching over from a running program Changing the program sequenceLoading or removing laundry Time remainingElectronic lock Activating the lockDeactivating the lock Cleaning and care Cleaning door lint filterCleaning the lint screen without water Cleaning the lint screen with waterCleaning port-hole grilles Cleaning the dryerTrouble shooting Test and fault messagesWhat to do, if . . . ? Problem Cause Solution Cancelling aCancelling the fault Light goes onOther faults Problem Cause Solution Synthetic-fiber laundry Items are staticallyCharged after drying There has been a lintStart and the indicator When switched onCold programs will not Lights for these programsReplacing the light bulb Customer service Program updatesWarranty conditions and warranty period Optional accessoriesInstallation and connection Front viewRear view Installation site Carrying the dryer to the installation siteWasher-dryer stack Ventilating the installation area Leveling the dryerElectrical connections Installing the dryer vent ProcedureGeneral AvoidCalculating total duct length Arrangement Left or right dryer vent openingRear or side exhaust connection Calculation exampleAt the rear Sideways to left or rightOverview of vent systems Flexible metal duct hoseExamples are shown on the next Examples Dryer vent systems from metal piping ExampleConnecting directly to a wall Side view vent Vent collector duct Washer-dryer stack Technical data Programmable functions for changing Standard values Programmable functions Extending the range of drying levelsAdjusting buzzer volume Buzzer normal default setting Buzzer loudFor programming and saving in memory, follow steps to No Memory default setting Set memory functionMemory Extending cooldown time Default setting Change function of Filter/Vent indicationAdjust keypad tone No Keypad tone default setting Keypad tone onChanging water conductivity setting Default setting Lower conductivity settingImportant condition Alteration rights reserved Nr 323 240