Miele T 7634 operating instructions Changing water conductivity setting, Important condition

Page 51

Programmable functions

Changing water conductivity setting

￿This programmable function should be adjusted only when residual water content is erroneously determined owing to the extreme softness of the water.

Important condition

The water in which fabrics are washed may be extremely soft with a conductivity value less than 150 μS/cm. Drinking water conductivity can be ascertained from your local water supplier.

Activate this programmable function only if the above-mentioned condition applies.

Otherwise the drying result will be unsatisfactory.

For programming and saving in memory, follow steps ￿ to ￿.

The function is programmed using the buttons.

Precondition:

The dryer is switched off.

The door is closed.

￿Press Start/Stop and keep it pressed it during steps ￿-￿.

￿Press the I-On/0-Offbutton in.

Wait until the Start/Stop button lights up continuously . . .

￿. . . then release the Start/Stop button.

￿Press the Gentle button six times.

The Gentle indicator light flashes once slowly and twice briefly.

P and 0 flash alternatingly in the display (default setting).

The number appearing alternatingly with P means:

0Default setting

ILower conductivity setting

(Express indicator light also flashes)

￿Pressing the Start/Stop button switches from one to the other.

￿Using the I-On/0-Offbutton, switch the dryer off.

The programming is now stored in memory. You can change it again at any time.

51

Image 51
Contents Operating Instructions Vented dryer 7634 Saving energy Caring for the environmentDisposal of packing material Disposing of your old applianceContents Contents Important Safety Instructions Grounding Instructions This dryer is intended for residential use onlyAccessories Display Fault indicator / Optical interfaceOperating the dryer Control panelDelay Program duration/ Estimated time remainingProgrammable functions Drying Care symbolsLaundry care Drying tipsLaundry care Turn on the dryer Proper dryingBrief instructions Preparing the laundryExtra options/Select Delay Select programDryness level selection in programs Starting the program Before the end of a programEnd of program Remove laundry Buzzer Options/DelayDelay GentleWrinkle-free Extra dry, Normal, Hand iron Program OverviewNormal Extra dry, Normal Hand iron, Rotary ironDress shirts Normal, Hand iron WoolensSmoothing Express Normal, Hand ironTimed warm Timed coldTime remaining Switching over from a running programChanging the program sequence Loading or removing laundryElectronic lock Activating the lockDeactivating the lock Cleaning the lint screen with water Cleaning and careCleaning door lint filter Cleaning the lint screen without waterCleaning the dryer Cleaning port-hole grillesTrouble shooting Test and fault messagesWhat to do, if . . . ? Light goes on Problem Cause SolutionCancelling a Cancelling the faultOther faults There has been a lint Problem Cause Solution Synthetic-fiber laundryItems are statically Charged after dryingLights for these programs Start and the indicatorWhen switched on Cold programs will notReplacing the light bulb Optional accessories Customer serviceProgram updates Warranty conditions and warranty periodFront view Installation and connectionRear view Installation site Carrying the dryer to the installation siteWasher-dryer stack Leveling the dryer Ventilating the installation areaElectrical connections Avoid Installing the dryer ventProcedure GeneralArrangement Left or right dryer vent opening Calculating total duct lengthSideways to left or right Rear or side exhaust connectionCalculation example At the rearOverview of vent systems Flexible metal duct hoseExamples are shown on the next Examples Example Dryer vent systems from metal pipingConnecting directly to a wall Side view vent Vent collector duct Washer-dryer stack Technical data Programmable functions for changing Standard values Extending the range of drying levels Programmable functionsAdjusting buzzer volume Buzzer normal default setting Buzzer loudFor programming and saving in memory, follow steps to No Memory default setting Set memory functionMemory Extending cooldown time Change function of Filter/Vent indication Default settingNo Keypad tone default setting Keypad tone on Adjust keypad toneChanging water conductivity setting Default setting Lower conductivity settingImportant condition Alteration rights reserved Nr 323 240