Miele T 4839 Ci operating instructions Aligning the appliance, Washer-dryer stack

Page 42

Installation

Aligning the appliance

Room in which the dryer is located

^Turn the 4 screw feet to adjust the dryer to the correct height and level.

Longer screw feet are available as an optional accessory. Unscrew and remove the feet supplied with the dryer before fitting the longer screw feet.

The cover plate on the dryer must be aligned horizontally underneath the worktop.

,The ventilation gaps in the plinth must not be covered over as this would prevent a sufficient intake of air.

Air taken in for use in the drying process will be warm when it is expelled from underneath the dryer. This expelled air heats up the air in the room. It is therefore very important to ensure that the room is adequately ventilated, particularly if the dryer is located in a small room. Otherwise running times and energy consumption could be increased.

Washer-dryer stack

The tumble dryer can also be combined with a Miele washing machine in a washer-dryer stack. To do this the appropriate stacking kit (WTV) (available to order) is required.

,The stacking kit must be fitted by suitably qualified fitter.

Before moving the tumble dryer again (e.g. when moving house)

After each use a small quantity of condensed water will collect in the area around the pump. This water can run out, if the dryer is tipped up when it is being moved. It is a good idea to run the Cool air programme for approximately 1 minute before moving the dryer. Any remaining condensed water will then be fed into the condensed water container or out through the drain hose.

42

Image 42

Contents Operating instructions For condenser tumble dryer T 4839 Ci Disposal of your old appliance Caring for the environmentDisposal of the packing material Energy saving tipsContents Contents Consumption data Technical data Safety with children Correct applicationTechnical safety Correct use Accessories Operating the tumble dryer Control panelSelecting and displaying settings DisplaySelecting programmes via the display Menu buttons Programme duration / Estimated time remainingSetting the time of day Before using for the first timeSetting the language Entry menuCare symbols Tips on dryingSort the laundry How to dry correctlyBrief instructions Turn on the tumble dryerSelect a programme Further programmesStart the programme Select any Extra options / Delay startRemove the laundry when the programme has finished Before the end of a programmeShort Low temperatureExtra options Anti-creaseTo begin delay start Delay startTo select delay start To alter delay startProgramme chart Woollens handcare DelicatesNormal+, Normal, Hand iron r, Hand iron rr, Machine iron AutomaticWarm air DenimCool air Standard pillows Normal drying levelOuterwear Silks handcareSportswear Proofing Normal drying levelMinimum iron hygiene Normal drying level Hygiene programmesCottons hygiene Normal drying level Timed drying hygieneAdding or removing laundry after a programme has started Changing the programme sequenceOnce a programme has started Time remainingCleaning and care Emptying the condensed water containerCleaning the fluff filters Cleaning them whilst dryCleaning them with water Cleaning the tumble dryer Cleaning the condenser unit Removing the condenser unitChecking the condenser unit Replacing the condenser unit Problem solving guide Fault messages in the displayProgramme has Is cancelled,Appears after FinishedOther problems Machine after Problem Possible cause Remedy Water leaks fromBeen cleaned Condenser unit hasWhen a programme is Problem Possible cause Remedy Programme doesIndicator light flashes Not startChanging the lamp Appliance guarantee After Sales serviceFuture updates PC Optional accessoriesInstallation Front viewInstallation site Building under a continous worktop / in a kitchen runBefore moving the tumble dryer again e.g. when moving house Aligning the applianceWasher-dryer stack Removing the spacer bars Front panel dimensions Fitting the front panelFitting the front panel Fitting a door front panel made by another manufacturer Preparing the front panelWith spacer bars Without spacer bars Preparing the fixing points Plinth facing dimensions InstallationFitting a plinth facing External condensed water outlet General notesArranging the drain hose Installation conditions requiring a non-return valve External drainage via a sink or gullyFit adapter 1 to the sink drain outlet Non-rewireable plugs BS Electrical connectionElectrical connection U.K Consumption data Large pillowsTechnical data Settings menu J for changing default settings To close the Settings menu Settings menu JTo open the Settings menu Language JExtended cool down Time of dayDrying levels To set the clock formatAirways indicator To activate the lock codeTo enter the lock code To use the dryer when the lock code is activated To deactivate the lock codeStandby display Keypad toneContrast Brightness MemoryAlteration rights reserved/2008