Miele T 4839 Ci operating instructions Keypad tone, Contrast Brightness, Standby display, Memory

Page 59

Settings menu J

Buzzer

The buzzer has two volumes.

Normal (Factory default)

The buzzer sounds at the end of a programme.

Loud

The buzzer sounds at maximum volume at the end of a programme.

A tick L will appear beside the option to show that it has been set.

Keypad tone

An audible tone sounds each time a button is pressed.

A tick L will appear beside the option to show that it has been set.

Factory default: Off.

Contrast

Brightness

There are ten different display contrast and display brightness settings.

The bar chart shows you the setting. Factory default: a medium setting.

Standby display

To save energy, the display goes out after 10 minutes and the indicator light for the Start/Stop button will start flashing slowly.

There are two options:

On

Standby is activated:

–if a programme is not selected within 10 minutes of the tumble dryer being switched on.

–10 minutes after a programme has started.

–10 minutes after the end of a programme.

Not in current prog. (Factory default)

–Standby is activated if a programme is not selected within 10 minutes of the tumble dryer being switched on and after the end of a programme. (Standby is not activated after a programme has started).

Pressing one of the buttons switches the display back on again.

A tick L will appear beside the option to show that it has been set.

Memory

The electronics will memorise the drying level and any extra options selected for the current drying programme.

A tick L will appear beside the option to show that it has been set.

Factory default: Off.

59

Image 59

Contents Operating instructions For condenser tumble dryer T 4839 Ci Energy saving tips Caring for the environmentDisposal of the packing material Disposal of your old applianceContents Contents Consumption data Technical data Correct application Safety with childrenTechnical safety Correct use Accessories Control panel Operating the tumble dryerSelecting programmes via the display Selecting and displaying settingsDisplay Programme duration / Estimated time remaining Menu buttonsEntry menu Before using for the first timeSetting the language Setting the time of dayTips on drying Care symbolsTurn on the tumble dryer How to dry correctlyBrief instructions Sort the laundryFurther programmes Select a programmeBefore the end of a programme Select any Extra options / Delay startRemove the laundry when the programme has finished Start the programmeAnti-crease Low temperatureExtra options ShortTo alter delay start Delay startTo select delay start To begin delay startProgramme chart Automatic DelicatesNormal+, Normal, Hand iron r, Hand iron rr, Machine iron Woollens handcareStandard pillows Normal drying level DenimCool air Warm airProofing Normal drying level Silks handcareSportswear OuterwearTimed drying hygiene Hygiene programmesCottons hygiene Normal drying level Minimum iron hygiene Normal drying levelTime remaining Changing the programme sequenceOnce a programme has started Adding or removing laundry after a programme has startedEmptying the condensed water container Cleaning and careCleaning them whilst dry Cleaning the fluff filtersCleaning them with water Cleaning the tumble dryer Removing the condenser unit Cleaning the condenser unitChecking the condenser unit Replacing the condenser unit Fault messages in the display Problem solving guideFinished Is cancelled,Appears after Programme hasOther problems Condenser unit has Problem Possible cause Remedy Water leaks fromBeen cleaned Machine afterNot start Problem Possible cause Remedy Programme doesIndicator light flashes When a programme isChanging the lamp Optional accessories After Sales serviceFuture updates PC Appliance guaranteeFront view InstallationBuilding under a continous worktop / in a kitchen run Installation siteWasher-dryer stack Before moving the tumble dryer again e.g. when moving houseAligning the appliance Removing the spacer bars Fitting the front panel Front panel dimensionsFitting the front panel With spacer bars Without spacer bars Fitting a door front panel made by another manufacturerPreparing the front panel Preparing the fixing points Fitting a plinth facing Plinth facing dimensionsInstallation Arranging the drain hose External condensed water outletGeneral notes External drainage via a sink or gully Installation conditions requiring a non-return valveFit adapter 1 to the sink drain outlet Electrical connection U.K Non-rewireable plugs BSElectrical connection Large pillows Consumption dataTechnical data Settings menu J for changing default settings Language J Settings menu JTo open the Settings menu To close the Settings menuTo set the clock format Time of dayDrying levels Extended cool downTo enter the lock code Airways indicatorTo activate the lock code To deactivate the lock code To use the dryer when the lock code is activatedMemory Keypad toneContrast Brightness Standby displayAlteration rights reserved/2008