Whirlpool MFW 9700S, MFW 9600S manual Electrician+

Page 14


					&)*($9
				1234567482937633 5
	')3 "#%$1234546$$$)				Do not ground to a gas pipe.
	')3 "#%$1234546$$$)				Check with a qualified electrician if you are not sure the
		$			washer is properly grounded.
					washer is properly grounded.
				$	Do not have a fuse in the neutral or ground circuit.
				$

					This washer must be grounded. In the event of a malfunction
					This washer must be grounded. In the event of a malfunction
					or breakdown, grounding will reduce the risk of electrical
					shock by providing a path of least resistance for electric
					current. This washer is equipped with a cord having an
					equipment-grounding conductor and a grounding plug. The
	3 prong grounding plug.				plug must be plugged into an appropriate outlet that is
	3 prong grounding plug.				&
	!&		(		properly installed and grounded in accordance with all local
	!&		(		codes and ordinances.
					!9 Improper connection of the equipment-
					grounding conductor can result in a risk of electric shock.
	A 120-volt, 60-Hz., AC-only, 15- or 20-amp, fused electrical				Check with a qualified electrician or serviceman if you are in
					doubt as to whether the appliance is properly grounded.
	supply is required. Time-delay fuse or circuit breaker is				doubt as to whether the appliance is properly grounded.
	supply is required. Time-delay fuse or circuit breaker is				Do not modify the plug provided with the appliance ? if it will
	recommended. It is recommended that a separate circuit
	serving only this appliance be provided.				not fit the outlet, have a proper outlet installed by a qualified
	This washer is equipped with a power supply cord having a				electrician"+(.	$9

To minimize possible shock hazard, the cord must be plugged into a mating, 3 prong, grounding-type outlet, grounded in accordance with local codes and ordinances. If a mating outlet is not available, it is the personal responsibility and obligation of the customer to have the properly grounded outlet installed by a qualified electrician.

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

This washer must be connected to a grounded metal, permanent wiring system, or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance.

9

3396865953

&- ("%$1234546$$#",.$#/+$($

Position the washer so that the rear of the washer is within approximately 3 ft (90 cm) of its final location.

There are 4 bolts in the rear panel of the washer that support the
suspension system during transportation. These bolts also retain
the power cord inside the washer until the bolts are removed.	Using a 13 mm wrench, loosen each of the bolts.

2-4

Image 14

Contents Epic Forward Goals and ObjectivesTable of Contents Wiring Diagram Safety First GeneralSerial Number Model & Serial Number DesignationsModel Number Model & Serial Number Label Tech Sheet Locations Specifications Maytag Corporation Major Appliance Warranty Page 1234566541728919243 7937226757947867 93278675445627 75445627834473#678#87968258928 $4487968258928Electrician+ 1233456768479346724 2273$%&%*$% ,&## 2$&+1234546#2&%2$!#2 &-.0$$+&. /+2+$ &+&+$&#0 7878 388787 #$%2&&8$87Theory of Operation AIR Vent System Pressure Switch Motor Control Unit MCU TOUCHPAD/LED AssemblyCentral Control Unit CCU Drive MotorSuspension System Pump MotorECO Valve Interlock Switches Heating Element Temperature SensorDoor LOCK/SWITCH Assembly 971771997 7271792869795947679476 42OFF56789797797998234567896358769795947 3462869795947679475694878594587 Modifier6.76676567786676712345678938294587 682 123455367892234563789345647 7397826739868934345$747 #5&61234567 Sturdy colorfast fabrics12345678935 888 88#$89777 8977897779 77 7#### Ordisconnect83783power83783 1234567 35 37 5 67 123456376468with liquid detergent64326%9894 %2435263 8312345674674 9728879Component Access Component LocationsRemoving the Console and the Touchpad / LED Assembly To remove the consoleTo remove the touchpad / LED assem- bly Door Lock/Switch Assembly Bellows Retaining Wire On the next To remove the door lock/switch as- semblyTo remove the front panel and bellows Remove the end of the dispenser tube from the bellows Removing the Flowmeter Removing the Detergent Dispenser Motor & Assembly To remove the detergent dispenser motorTo remove the detergent dispenser as- sembly Removing the Inlet Valves Removing the Central Control Unit Removing the Interference Filter Removing the Pressure Switch Removing the Motor Controller Wire Standoff To remove the heating element Removing the Temperature Sensor Heating ElementTo remove the temperature sensor Removing the Drain Pump Assembly Removing the Airtrap Removing AN Interlock Switch Rotate Switch Up Switch Holder Locking Tabs Removing the Drive Motor Pivot Stud Removing the TUB and Basket Assembly Align Tabs With Slots Support Weight While Removing Front Slot Front Holes Rear Half Of Tub Basket Front Half Of Tub Reassembly Notes Page Component Testing Water Level Setting Test PointsMotor & Switch Detergent DispenserTo test the door lock/unlock solenoids To test the door switchTo test the door lock main switches Drain Pump Motor Interference FilterTemperature Results Interlock Switch Electrostatic Discharge ESD Sensitive Electronics DiagnosticsDiagnostic Guide FAILURE/ERROR Display Codes Display Explanation and Recommended ProcedureLong Drain Motor Control Unit Error Dispenser Circuit Error CCU / Touchpad / LED Assembly Error Sud Test Program Control Diagnostic TestStarting the Test Mode Manually Unlocking Door Lock System Water Temperature SensorMotor Continuity Test To reassemble CCU To remove the touchpad/LED assemblyTo remove Central Control Unit CCU To remove Motor Control Unit MCUTroubleshooting Chart ProblemDrum will Incorrect Page Wiring Diagram Page Product Specifications Warranty Information Sources United States