Whirlpool MFW 9600S, MFW 9700S manual Reassembly Notes

Page 63

REASSEMBLY NOTES:

1.When reassembliing the tub, install the metal clips over the flanges of the two tub sections with a hammer.

3.When reinstalling the bottom front coun- terweight, first tape the flat nut in place in the tub slot so it does not fall out.

Tub Clamp

Tub Flanges

2.When reinstalling the tub assembly, hook the two suspension springs into the front holes of the tub and cabinet.

Front Slot

 

Front Slot

 

 

 

Front Holes

Bottom Front Counterweight Flat Nut

4. When reinstalling the heating element in the tub, make sure that it is held in place by the wire holder (see the photo in step 27 on the previous page).

Heating

Element

4-28

Page 62 Page 64
Image 63
Page 62 Page 64
Contents Epic Goals and Objectives ForwardTable of Contents Wiring Diagram General Safety FirstModel & Serial Number Designations Model NumberSerial Number Model & Serial Number Label Tech Sheet Locations Specifications Maytag Corporation Major Appliance Warranty Page 79372 123456654172891924375445627834473 93278675445627 26757947867$4487968258928 #678#87968258928Electrician+ 2273 1233456768479346724$%&%*$% ,&## 2$&+1234546#2&%2$!#2 &-.0$$+&. /+2+$ &+&+$&#0 #$%2&&8$87 388787 7878Theory of Operation AIR Vent System Pressure Switch Drive Motor TOUCHPAD/LED AssemblyCentral Control Unit CCU Motor Control Unit MCUPump Motor ECO ValveSuspension System Heating Element Temperature Sensor Door LOCK/SWITCH AssemblyInterlock Switches 72717 971771997346286979594767947 42OFF56789797797998234567896358769795947 92869795947679476Modifier6.766765677866767 123456789382945875694878594587 7397826739868934345 123455367892234563789345647 682#5&6 $747Sturdy colorfast fabrics 123456712345678935 88#$ 88877 7# 8977897779 89777Ordisconnect83783power 83783### 123456376468with liquid detergent64326%9894 %24 352631234567 35 37 5 67 9728879 8312345674674Component Locations Component AccessTo remove the console Removing the Console and the Touchpad / LED AssemblyTo remove the touchpad / LED assem- bly Door Lock/Switch Assembly Bellows Retaining Wire To remove the door lock/switch as- sembly To remove the front panel and bellowsOn the next Remove the end of the dispenser tube from the bellows Removing the Flowmeter To remove the detergent dispenser motor Removing the Detergent Dispenser Motor & AssemblyTo remove the detergent dispenser as- sembly Removing the Inlet Valves Removing the Central Control Unit Removing the Interference Filter Removing the Pressure Switch Removing the Motor Controller Wire Standoff Removing the Temperature Sensor Heating Element To remove the temperature sensorTo remove the heating element Removing the Drain Pump Assembly Removing the Airtrap Removing AN Interlock Switch Rotate Switch Up Switch Holder Locking Tabs Removing the Drive Motor Pivot Stud Removing the TUB and Basket Assembly Align Tabs With Slots Support Weight While Removing Front Slot Front Holes Rear Half Of Tub Basket Front Half Of Tub Reassembly Notes Page Water Level Setting Test Points Component TestingDetergent Dispenser Motor & SwitchTo test the door switch To test the door lock main switchesTo test the door lock/unlock solenoids Interference Filter Drain Pump MotorTemperature Results Interlock Switch Diagnostics Diagnostic GuideElectrostatic Discharge ESD Sensitive Electronics Display Explanation and Recommended Procedure FAILURE/ERROR Display CodesLong Drain Motor Control Unit Error Dispenser Circuit Error CCU / Touchpad / LED Assembly Error Sud Diagnostic Test Starting the Test ModeTest Program Control Water Temperature Sensor Motor Continuity TestManually Unlocking Door Lock System To remove Motor Control Unit MCU To remove the touchpad/LED assemblyTo remove Central Control Unit CCU To reassemble CCUProblem Troubleshooting ChartDrum will Incorrect Page Wiring Diagram Page United States Product Specifications Warranty Information Sources
Top Page Image Contents