Whirlpool MFW 9600S, MFW 9700S manual Long Drain

Page 73

	DISPLAY		EXPLANATION AND RECOMMENDED PROCEDURE

		LONG DRAIN

		If the drain time exceeds eight minutes, the water valves are turned off and “F/02 ” is flashed.
		Press PAUSE/CANCEL two times to clear the display.
		NOTE: After four minutes the “Sud” error will be displayed, then four minutes later the “F/02 ”
	F/02	error code will be displayed..

		Possible Causes / Procedure
		Possible Causes / Procedure
		1.	Check the drain hose and make sure it is not plugged or kinked.
		2.	Unplug washer or disconnect power.
		3.	Check the electrical connections at the pump and make sure the pump is running.
		4.	Check the drain pump filter for foreign objects.
		5.	Plug in washer or reconnect power.
		6.	If the above does not correct the problem, go to step 7.
		7.	Unplug washer or disconnect power.
		8.	Replace the pump.

		WATER TEMPERATURE SENSOR ERROR

	F/05	If during the water heating step in the wash cycle, the water temperature sensor (NTC) value
	F/05	is out of range, the “F/05” error code will be displayed.

		Possible Causes / Procedure
		1.	Unplug washer or disconnect power.
		2.	Check the water temperature sensor. Refer to the “Water Temperature Sensor ” section.
			Check connections to the water temperature sensor.
		3.	Check resistance of heating element, if present on this model. (abnormal = infinity)

		DRIVE MOTOR TACHOMETER ERROR

		The control is unable to properly detect motor speed and the machine will shut down. If a fail-
		ure occurs during high-speed spin, the door will be unlocked after three minutes.
	F/06
	F/06	Possible Causes / Procedure
		1.	Verify the shipping system including shipping bolts, spacers and cables are removed.
		2.	Unplug washer or disconnect power.
		3.	Check wire harness connections between the drive motor and the Motor Control Unit
			(MCU), and between the MCU and the Central Control Unit (CCU).
		4.	Plug in washer or reconnect power.
		5.	Check the MCU by looking for operations of the drive motor.
		6.	Check the drive motor for powered rotations.

6-3

Image 73

Contents Epic Goals and Objectives ForwardTable of Contents Wiring Diagram General Safety FirstModel Number Model & Serial Number DesignationsSerial Number Model & Serial Number Label Tech Sheet Locations Specifications Maytag Corporation Major Appliance Warranty Page 79372 12345665417289192438675445627 932726757947867 75445627834473$4487968258928 #678#87968258928Electrician+ 2273 1233456768479346724$%&%*$% ,&## 2$&+1234546#2&%2$!#2 &-.0$$+&. /+2+$ &+&+$&#0 787 3887878 #$%2&&8$87Theory of Operation AIR Vent System Pressure Switch Central Control Unit CCU TOUCHPAD/LED AssemblyMotor Control Unit MCU Drive MotorECO Valve Pump MotorSuspension System Door LOCK/SWITCH Assembly Heating Element Temperature SensorInterlock Switches 72717 9717719978234567896358769795947 42OFF567897977979992869795947679476 34628697959476794712345678938294587 Modifier6.7667656778667675694878594587 345647 123455367892234563789682 7397826739868934345#5&6 $747Sturdy colorfast fabrics 123456712345678935 88#$ 888897779 897789777 77 7#83783 Ordisconnect83783power### 35263 123456376468with liquid detergent64326%9894 %241234567 35 37 5 67 9728879 8312345674674Component Locations Component AccessTo remove the console Removing the Console and the Touchpad / LED AssemblyTo remove the touchpad / LED assem- bly Door Lock/Switch Assembly Bellows Retaining Wire To remove the front panel and bellows To remove the door lock/switch as- semblyOn the next Remove the end of the dispenser tube from the bellows Removing the Flowmeter To remove the detergent dispenser motor Removing the Detergent Dispenser Motor & AssemblyTo remove the detergent dispenser as- sembly Removing the Inlet Valves Removing the Central Control Unit Removing the Interference Filter Removing the Pressure Switch Removing the Motor Controller Wire Standoff To remove the temperature sensor Removing the Temperature Sensor Heating ElementTo remove the heating element Removing the Drain Pump Assembly Removing the Airtrap Removing AN Interlock Switch Rotate Switch Up Switch Holder Locking Tabs Removing the Drive Motor Pivot Stud Removing the TUB and Basket Assembly Align Tabs With Slots Support Weight While Removing Front Slot Front Holes Rear Half Of Tub Basket Front Half Of Tub Reassembly Notes Page Water Level Setting Test Points Component TestingDetergent Dispenser Motor & SwitchTo test the door lock main switches To test the door switchTo test the door lock/unlock solenoids Interference Filter Drain Pump MotorTemperature Results Interlock Switch Diagnostic Guide DiagnosticsElectrostatic Discharge ESD Sensitive Electronics Display Explanation and Recommended Procedure FAILURE/ERROR Display CodesLong Drain Motor Control Unit Error Dispenser Circuit Error CCU / Touchpad / LED Assembly Error Sud Starting the Test Mode Diagnostic TestTest Program Control Motor Continuity Test Water Temperature SensorManually Unlocking Door Lock System To remove Central Control Unit CCU To remove the touchpad/LED assemblyTo reassemble CCU To remove Motor Control Unit MCUProblem Troubleshooting ChartDrum will Incorrect Page Wiring Diagram Page United States Product Specifications Warranty Information Sources