Avaya 518-456-804 manual Grounding the System, Inserting Batteries in the Processor Module

Page 19

Quick Reference Guide	2 Installing Your System

Grounding the System

You ground the system by running a solid copper wire from the processor module to an appropriate earth ground. Follow these steps to ground the system:

1Attach one end of a #12 AWG or #14 AWG solid copper wire to the grounding screw on the processor module. The length of the wire must not exceed 35 feet (7.6 meters).

2Route the wire through the wire manager on the front of the module.

3Attach the other end of the wire to the approved earth ground, such as building steel or a cold water pipe.

Inserting Batteries in the Processor Module

The processor module uses two AAA-size standard alkaline batteries to guard against the loss of system programming in case of a power failure. These batteries retain the system programming for 45 days to six months, depending on the freshness of the batteries. You should replace the batteries every year.

The configuration of the 1600 DSL module is not backed up to the PCMCIA card. Instead, the configuration is retained in the flash memory of the 1600 DSL module.

CAUTION:

Batteries and battery cover are packaged in a separate box. If you are replacing batteries, the old batteries must be removed with the power on or the system’s memory will be lost.

Follow these steps to insert the batteries:

1Locate the battery compartment at the bottom of the PARTNER ACS processor module, below the extension jacks.

2Push gently on the battery icon (the locking latch) and slide the battery icon up to cover the plus icon; this unlocks the battery assembly.

3Remove the battery assembly by gently pulling the tab at the bottom of the battery compartment cover.

Installing the Control Unit 19

Image 19

Contents Partner Copyright Document Avaya Inc Important Safety Instructions Page Contents Programming Telephone Features System Overview WelcomeSystem Configurations System Components System CapacitySystem Components Description Opre Auxiliary EquipmentGetting Acquainted Overview Installing Your SystemEvaluating the Environment Installing the Control UnitGo to the next procedure, Labeling Jacks, on Wall-Mounting a 5-Slot Carrier and Modules Quick Reference Guide Labeling Jacks Inserting Batteries in the Processor Module Grounding the SystemInstalling Your System Initializing the System Checking the LEDs Connecting Lines and Extensions Installing Your System Connecting the Loudspeaker Paging System Installing Your System Installing Telephones Installing the CoverConnecting Auxiliary Equipment Setting Up Your System System Programming Basics Setting Up Your System Programming Overlays Button Locations Button Locations on Partner Telephones Changing Programming Type Programming ModeUsing Centralized Telephone Programming System Date #101 Setting the Date and TimeSystem Time #103 Automatic Daylight/Standard Times #126 Administering the Loudspeaker Paging SystemAssigning Lines Customizing Extensions Copy Settings #399 Recall Setting Changing Settings to Support PBX or Centrex ServicesDialing Restrictions Speed Dial and Auto Dial Numbers Emergency Phone Number List #406Voice Messaging Systems Programming for Voice Messaging Systems Additional Voice Messaging System Programming System Speed Dial Programming System Features5554757 Dialing Restrictions and PermissionsSecurity Alert Allowed Phone Number Lists #407Allowed List Assignments #408 Disallowed Phone Number Lists #404 Disallowed List Assignments #405 Line Access Restriction #302Current restriction appears Outgoing Call Restriction #401 Group...Description Groups of ExtensionsProgramming System Features Programming Telephone Features Automatic Line Selection Letters Numbers Extension Name DisplayLetters Numbers Line Ringing Programming Telephone Features Maintaining Your System Backup and Restore Backup Programming-Automatic #123 Backup Programming-Manual #124 Restore Programming #125 Maintaining Your System Battery Replacement Using a PC Card Power up the system Reconnect the power cord Maintaining Your System Check the LEDs Upgrading 1600 DSL and 012E Module FirmwareUpgrading T1 Module Firmware Adding New Modules Maintaining Your System Replacing Modules Maintaining Your System Replacing Modules in a 5-Slot Carrier Maintaining Your System Reconnect the power cord Changing the System Clock Changing System SettingsAdding New Lines Adding Lines, Pools, and ExtensionsPooled Extensions Adding New Extensions Adding New PoolsSwapping Extensions Maintaining Your System Your Release Number If Something Doesn’t WorkPress f00ss#123 Clearing a Backup-Failure Alarm012E Module Power Management Problem Check this Telephone ProblemsProblem Check this Telephone Doesn’t Work on Calling ProblemsQuick Reference Guide If Something Doesn’t Work System Problems T1 Module Problems ATM DSL Module ProblemsTip/Ring Device Problems 98 Tip/Ring Device Problems System Programming Flow Chart-How to Use System Flow Chart-System System Reset-Programming Saved Mode of OperationHold Reminder Tone System Flow Chart-Lines System Flow Chart-System Speed Dial NumbersSystem Flow Chart-Extensions External Hotline Line Access ModePool Access Restriction Copy SettingsSystem Flow Chart-Dialing Restrictions and Permissions System Flow Chart-Groups System Flow Chart-Auxiliary Equipment Application Programming Interface API Internal Monitor Music-On-Hold VolumeRemote Administration Password Application Programming Interface APITo Erase a Feature or Auto Dial Button Centralized Telephone Programming Flow Chart-How to UseTo Program Another Feature at the Same Extension To Change Setting for Another ExtensionCentralized Telephone Programming Flow Chart Conference Drop For voice signaling the first available extensionManual Signaling Touch-Tone EnableExtension Telephone Programming Flow Chart-How to Use Auto Dial Numbers-Outside and Inside Extension Telephone Programming Flow Chart114 Voice Mailbox Transfer 116