Avaya 518-456-804 manual Initializing the System

Page 21

Quick Reference Guide	2 Installing Your System

Initializing the System

Before you initialize the system, you may insert any of the supported PC cards: Backup/Restore card, Automatic System Answer/Direct Extension Dial (ASA/DXD) card, PARTNER Voice Messaging Basics card, and PARTNER Remote Access PC Card.

You must power down the system before you insert or remove a PC Card.

Follow these steps to initialize a system:

1If you have a PC Card, perform the following steps:

aIf your PC Card comes with a write-protect tab, verify that the write-protect tab on the PC Card is not in the write-protected position. If it is, use a paperclip or another pointed object to push the write-protect tab on the end of the PC Card upward to the nonprotected position.

bTo insert the PC Card, hold it with the label facing to the right, and slide it gently into one of the PC Card slots on the processor module. When inserted properly, the PC Card projects about 1-5/8” (4 cm) from the module.

2If you have a 5-slot carrier, make sure the carrier’s On/Off switch is at the Off (“O”) position.

3Press the power cord firmly into the power jack on the carrier or the stand-alone processor module until the cord locks into place.

4Plug the other end of the power cord into a properly grounded three-prong wall outlet that is not controlled by a switch.

5If you have a 5-slot carrier, move the On/Off switch to the On (“—”) position.

CAUTION:

The power cord should hang straight down from the connector for the entire length of the module or carrier. Do not install the power cord at an angle to the case or with a loop in it.

Installing the Control Unit 21

Image 21

Contents Partner Copyright Document Avaya Inc Important Safety Instructions Page Contents Programming Telephone Features System Overview WelcomeSystem Configurations System Components System CapacitySystem Components Description Opre Auxiliary EquipmentGetting Acquainted Overview Installing Your SystemEvaluating the Environment Installing the Control UnitGo to the next procedure, Labeling Jacks, on Wall-Mounting a 5-Slot Carrier and Modules Quick Reference Guide Labeling Jacks Inserting Batteries in the Processor Module Grounding the SystemInstalling Your System Initializing the System Checking the LEDs Connecting Lines and Extensions Installing Your System Connecting the Loudspeaker Paging System Installing Your System Installing Telephones Installing the CoverConnecting Auxiliary Equipment Setting Up Your System System Programming Basics Setting Up Your System Programming Overlays Button Locations Button Locations on Partner Telephones Changing Programming Type Programming ModeUsing Centralized Telephone Programming Setting the Date and Time System Date #101System Time #103 Automatic Daylight/Standard Times #126 Administering the Loudspeaker Paging SystemAssigning Lines Customizing Extensions Copy Settings #399 Changing Settings to Support PBX or Centrex Services Recall SettingDialing Restrictions Speed Dial and Auto Dial Numbers Emergency Phone Number List #406Voice Messaging Systems Programming for Voice Messaging Systems Additional Voice Messaging System Programming System Speed Dial Programming System Features5554757 Dialing Restrictions and PermissionsSecurity Alert Allowed Phone Number Lists #407Allowed List Assignments #408 Disallowed Phone Number Lists #404 Disallowed List Assignments #405 Line Access Restriction #302Current restriction appears Outgoing Call Restriction #401 Group...Description Groups of ExtensionsProgramming System Features Programming Telephone Features Automatic Line Selection Letters Numbers Extension Name DisplayLetters Numbers Line Ringing Programming Telephone Features Maintaining Your System Backup and Restore Backup Programming-Automatic #123 Backup Programming-Manual #124 Restore Programming #125 Maintaining Your System Battery Replacement Using a PC Card Power up the system Reconnect the power cord Maintaining Your System Check the LEDs Upgrading 1600 DSL and 012E Module FirmwareUpgrading T1 Module Firmware Adding New Modules Maintaining Your System Replacing Modules Maintaining Your System Replacing Modules in a 5-Slot Carrier Maintaining Your System Reconnect the power cord Changing the System Clock Changing System SettingsAdding New Lines Adding Lines, Pools, and ExtensionsPooled Extensions Adding New Pools Adding New ExtensionsSwapping Extensions Maintaining Your System Your Release Number If Something Doesn’t WorkPress f00ss#123 Clearing a Backup-Failure Alarm012E Module Power Management Problem Check this Telephone ProblemsProblem Check this Telephone Doesn’t Work on Calling ProblemsQuick Reference Guide If Something Doesn’t Work System Problems T1 Module Problems ATM DSL Module ProblemsTip/Ring Device Problems 98 Tip/Ring Device Problems System Programming Flow Chart-How to Use System Flow Chart-System Mode of Operation System Reset-Programming SavedHold Reminder Tone System Flow Chart-Lines System Flow Chart-System Speed Dial NumbersSystem Flow Chart-Extensions Pool Access Restriction Line Access ModeCopy Settings External HotlineSystem Flow Chart-Dialing Restrictions and Permissions System Flow Chart-Groups System Flow Chart-Auxiliary Equipment Remote Administration Password Music-On-Hold VolumeApplication Programming Interface API Application Programming Interface API Internal MonitorTo Program Another Feature at the Same Extension Centralized Telephone Programming Flow Chart-How to UseTo Change Setting for Another Extension To Erase a Feature or Auto Dial ButtonCentralized Telephone Programming Flow Chart Manual Signaling For voice signaling the first available extensionTouch-Tone Enable Conference DropExtension Telephone Programming Flow Chart-How to Use Auto Dial Numbers-Outside and Inside Extension Telephone Programming Flow Chart114 Voice Mailbox Transfer 116