Avaya 518-456-804 manual Reconnect the power cord

Page 81

Quick Reference Guide	6 Maintaining Your System

10Reconnect the power cord.

CAUTION:

The power cord should hang straight down from the connector, flush against the plastic case. Do not install the power cord at an angle to the case or with a loop in it.

11Move the carrier’s On/Off switch to the “On” position (“—”).

12Check that all green lights on the fronts of the modules are lit:

•If a single light is out, power down the control unit, reseat the module, and power up the control unit.

•If multiple lights are out, power down the control unit, reseat the leftmost module that has a light out, and power up the control unit.

•If the lights are still out, call for support as instructed on the inside front cover of this guide.

13Make sure all modules are seated properly. (The cover will not fit if the modules are not seated properly.)

14Perform the following steps to replace the cover:

aPosition the carrier cover over the modules so that the openings on the top of the carrier cover align correctly with the tabs at the top of the installed 5-slot carrier and modules.

bRotate the carrier cover into position so that it aligns correctly with the thumb screw opening on the bottom of the carrier.

cTighten the thumb screw. To ensure proper alignment and safe operation, tighten the thumb screw securely.

Replacing Modules 81

Image 81

Contents Partner Copyright Document Avaya Inc Important Safety Instructions Page Contents Programming Telephone Features System Overview WelcomeSystem Configurations System Components System CapacitySystem Components Description Opre Auxiliary EquipmentGetting Acquainted Overview Installing Your SystemEvaluating the Environment Installing the Control UnitGo to the next procedure, Labeling Jacks, on Wall-Mounting a 5-Slot Carrier and Modules Quick Reference Guide Labeling Jacks Inserting Batteries in the Processor Module Grounding the SystemInstalling Your System Initializing the System Checking the LEDs Connecting Lines and Extensions Installing Your System Connecting the Loudspeaker Paging System Installing Your System Installing Telephones Installing the CoverConnecting Auxiliary Equipment Setting Up Your System System Programming Basics Setting Up Your System Programming Overlays Button Locations Button Locations on Partner Telephones Changing Programming Type Programming ModeUsing Centralized Telephone Programming Setting the Date and Time System Date #101System Time #103 Automatic Daylight/Standard Times #126 Administering the Loudspeaker Paging SystemAssigning Lines Customizing Extensions Copy Settings #399 Changing Settings to Support PBX or Centrex Services Recall SettingDialing Restrictions Speed Dial and Auto Dial Numbers Emergency Phone Number List #406Voice Messaging Systems Programming for Voice Messaging Systems Additional Voice Messaging System Programming System Speed Dial Programming System Features5554757 Dialing Restrictions and PermissionsSecurity Alert Allowed Phone Number Lists #407Allowed List Assignments #408 Disallowed Phone Number Lists #404 Disallowed List Assignments #405 Line Access Restriction #302Current restriction appears Outgoing Call Restriction #401 Group...Description Groups of ExtensionsProgramming System Features Programming Telephone Features Automatic Line Selection Letters Numbers Extension Name DisplayLetters Numbers Line Ringing Programming Telephone Features Maintaining Your System Backup and Restore Backup Programming-Automatic #123 Backup Programming-Manual #124 Restore Programming #125 Maintaining Your System Battery Replacement Using a PC Card Power up the system Reconnect the power cord Maintaining Your System Check the LEDs Upgrading 1600 DSL and 012E Module FirmwareUpgrading T1 Module Firmware Adding New Modules Maintaining Your System Replacing Modules Maintaining Your System Replacing Modules in a 5-Slot Carrier Maintaining Your System Reconnect the power cord Changing the System Clock Changing System SettingsAdding New Lines Adding Lines, Pools, and ExtensionsPooled Extensions Adding New Pools Adding New ExtensionsSwapping Extensions Maintaining Your System Your Release Number If Something Doesn’t WorkPress f00ss#123 Clearing a Backup-Failure Alarm012E Module Power Management Problem Check this Telephone ProblemsProblem Check this Telephone Doesn’t Work on Calling ProblemsQuick Reference Guide If Something Doesn’t Work System Problems T1 Module Problems ATM DSL Module ProblemsTip/Ring Device Problems 98 Tip/Ring Device Problems System Programming Flow Chart-How to Use System Flow Chart-System Mode of Operation System Reset-Programming SavedHold Reminder Tone System Flow Chart-Lines System Flow Chart-System Speed Dial NumbersSystem Flow Chart-Extensions Pool Access Restriction Line Access ModeCopy Settings External HotlineSystem Flow Chart-Dialing Restrictions and Permissions System Flow Chart-Groups System Flow Chart-Auxiliary Equipment Remote Administration Password Music-On-Hold VolumeApplication Programming Interface API Application Programming Interface API Internal MonitorTo Program Another Feature at the Same Extension Centralized Telephone Programming Flow Chart-How to UseTo Change Setting for Another Extension To Erase a Feature or Auto Dial ButtonCentralized Telephone Programming Flow Chart Manual Signaling For voice signaling the first available extensionTouch-Tone Enable Conference DropExtension Telephone Programming Flow Chart-How to Use Auto Dial Numbers-Outside and Inside Extension Telephone Programming Flow Chart114 Voice Mailbox Transfer 116