Graco ti18526c Flush Before First Use, Fill Supply Tanks, Solvent Flush Connections if applicable

Page 23

Setup

Solvent Flush Connections (if applicable)

NOTE: See Solvent Flush Systems component identi- fication on page 15 for connection locations.

13.Connect solvent air line from air control panel to dia- phragm pump or pressure pot air inlet.

14.Connect solvent suction tube from solvent supply tank to solvent pump fluid inlet.

15.Connect solvent line from gun hose bundle to sol- vent fluid outlet.

Gun Connections

16.For 25 ft and 35 ft hose bundles only: Place the coil of resin hose in the hose bundle on the hook sup- port located on the pole. Secure with the supplied rubber straps. The hook support should be inserted through the center of the hose coil.

17.Secure all connections on the whip-end of the hose bundle to the gun. See the gun manual listed on page 3 for detailed instructions.

Flush Before First Use

Oil left in the system at the factory can react with cata- lyst and create a fire or explosion.

Flush before first use.

Do not add catalyst to the catalyst reservoir until the system has been flushed.

Flush the system before first use to prevent contaminat- ing the resin or catalyst. See page 30.

Fill Supply Tanks

Add fluid to the solvent flush supply tank (if applicable), the catalyst supply reservoir, and the resin supply con- tainer.

3A2012J

23

Image 23
Contents FRP Proportioner Important Safety InstructionsContents Manual Description Related ManualsAgency Approvals Length Ratio ModelsNo Cart Cart, Mast, and Boom HoseAccessories Skin Injection Hazard Toxic Fluid or Fumes Hazard 3A2012J Keep Resin and Catalyst Components Separate Important Two-Component Material InformationMaterial Self-ignition Changing MaterialsTypical Applications OverviewKey Component IdentificationAir Control Panel Pressurized fluid outlet on filter R connect fluid Air Motor and Resin Displacement PumpPressure relief/recirculation valve P relieves pres Pressure relief/recirculation fluid outlet P1 placeCatalyst Pump Components Catalyst PumpSolvent Flush Asme and CE-Approved Pressure Pot Solvent Flush SystemsSolvent Flush Diaphragm Pump System Mounting Wall Mount Systems Only SetupBefore Installation Location RequirementsFor systems bolting directly to wall not using a pole For cart and boom systems only, install legs System AssemblySpring Chain Roving Guides Deflector Plates Grounding Ground WireAir Connections Connect Fluid and Air LinesCatalyst Pump Pressure Relief Valve Gun Connections Flush Before First UseFill Supply Tanks Solvent Flush Connections if applicableBoom Operation Pressure Relief Procedure and ShutdownOperation Trigger LockOperation For internal mix proportioners only, check solvent line StartupPrime Follow Pressure Relief Procedure and Shut- down onOperation 3A2012J Flush External mix systems 30-40 psi 0.21-0.28 MPa, 2.1-2.8 bar SprayFollow Pressure Relief Procedure and Shutdown on AAC Air AdjustmentDataTrak Operation Run ModeSetup Mode Operation Solenoid Release Button Runaway MonitorDisplay DiagnosticsPrime/Flush Counter/TotalizerDiagnostic Codes Symbol Code Name Diagnosis Cause Disconnect DataTrak Replace DataTrak Battery or FuseTask Schedule Inspect pump wetcup Daily MaintenanceComponents Resin Pump TroubleshootingSpray pattern Mendations Fluid is too thin or too thick General Information Disconnect the Displacement PumpRepair Align cylinder and adapter plate Reconnect the Displacement PumpReconnect the Air Motor Disconnect the Air MotorTi18456c Replace Pumpline Repair Throat and Piston Seals Repair Catalyst PumpRemove Catalyst Pump from System Disassemble Catalyst PumpAssemble Catalyst Pump Repair Foot ValveCatalyst Pump Details Systems System Parts152 24M692 SPACER, ball joint Wall or Pole Mount KIT Wall or Pole Mount KIT Wall or Pole Mount KIT Quantity CartsSystem Parts Part Description Qty Wall or Pole Mount Kit, 16N918Boom, 16N761 Air Panel Slave Pump Linkage, 16P125 Part Description 131 171 Resin PumplinesCoupling Collars Connecting KitAir Motor and Pump for Resin Pumpline GunMesh Pack Resin Filter24F620 16M736 Resin Supply Hose3A2012J 922 930 940 Catalyst Slave PumpsCatalyst Pumps Installation Tools not shown16P425 Catalyst ReservoirCart not included in kit, shown for reference only Hose Bundles Quantity 16N0169, 16N017, 16N018, and 16N019 Kits Accessory Parts Heater Kits16N014 and 16N015 Kits Nipple Asme Pressure Pots, 2-gallon 16M893 and 5-gallon 16M894 Solvent Pressure Pot KitsTube Asme and CE-Approved Pressure Pots, 16M874 and 16M875Gallon 16M560 and 5-gallon 16M561 Solvent Diaphragm Pumps16M881 DataTrak Upgrade KitCarts for 55 Gallon Barrel, 16M896 16M961 Roving Box BracketFor external gel Extension HosesGel Hose Chop HoseTop View DimensionsCart and Boom Wall/Pole Mount Cart OnlyPumpline Wall Mounting Bracket Dimensions Technical DataPumpline Technical Data 3A2012J Graco Information Graco Standard Warranty