Graco ti18526c, ti18524d, ti18496b specifications Runaway Monitor, Solenoid Release Button

Page 35

Setup Mode

1.See FIG. 31. Press and hold for 5 seconds until Setup menu appears.

2.To enter settings for runaway, lower size, and flow rate units, and to enable runaway, E1, E2, and E5

error options, press to change the value, then

to save the value and move the cursor to the next data field. See page for a description of E1, E2, and E5 error codes.

Operation

NOTE: When runaway, E1, E2, and E5 error options are enabled, a will appear on the setup screen. See FIG. 31.

3.Move the cursor to the E5 error enable option field,

then press once more to exit Setup mode.

Run Mode

Runaway Monitor

1.See FIG. 31. If pump runaway occurs, the runaway solenoid will actuate, stopping the pump. The LED (CD) will flash and the display (CF) will indicate a runaway condition (see Table 1). The display will cycle through six instruction screens.

2.Runaway Screens 1 and 2: To reset the runaway solenoid, close the master air valve (AP). Wait for air to completely bleed off the air motor.

AP

3.Runaway Screens 3 and 4: After the air is bled off, push the solenoid release button (J) down to reset the air valve. The button will pop back up when the air valve is repressurized.

J

ti11902a

FIG. 32. Solenoid Release Button

4.Runaway Screens 5 and 6: Press to clear the diagnostic code and reset the runaway solenoid.

5. Open master air valve (AP) to restart pump.

NOTE: To disable runaway monitoring, go to setup mode and set runaway value (CA) to 0 (zero) or disable

(RT)

(see FIG. 31).

3A2012J

35

Image 35
Contents FRP Proportioner Important Safety InstructionsContents Manual Description Related ManualsAgency Approvals Length Ratio ModelsNo Cart Cart, Mast, and Boom HoseAccessories Skin Injection Hazard Toxic Fluid or Fumes Hazard 3A2012J Keep Resin and Catalyst Components Separate Important Two-Component Material InformationMaterial Self-ignition Changing MaterialsTypical Applications OverviewKey Component IdentificationAir Control Panel Pressurized fluid outlet on filter R connect fluid Air Motor and Resin Displacement PumpPressure relief/recirculation valve P relieves pres Pressure relief/recirculation fluid outlet P1 placeCatalyst Pump Components Catalyst PumpSolvent Flush Asme and CE-Approved Pressure Pot Solvent Flush SystemsSolvent Flush Diaphragm Pump System Mounting Wall Mount Systems Only SetupBefore Installation Location RequirementsFor systems bolting directly to wall not using a pole For cart and boom systems only, install legs System AssemblySpring Chain Roving Guides Deflector Plates Grounding Ground WireAir Connections Connect Fluid and Air LinesCatalyst Pump Pressure Relief Valve Gun Connections Flush Before First UseFill Supply Tanks Solvent Flush Connections if applicableBoom Operation Pressure Relief Procedure and ShutdownOperation Trigger LockOperation For internal mix proportioners only, check solvent line StartupPrime Follow Pressure Relief Procedure and Shut- down onOperation 3A2012J Flush External mix systems 30-40 psi 0.21-0.28 MPa, 2.1-2.8 bar SprayFollow Pressure Relief Procedure and Shutdown on AAC Air AdjustmentDataTrak Operation Run ModeSetup Mode Operation Solenoid Release Button Runaway MonitorDisplay DiagnosticsPrime/Flush Counter/TotalizerDiagnostic Codes Symbol Code Name Diagnosis Cause Disconnect DataTrak Replace DataTrak Battery or FuseTask Schedule Inspect pump wetcup Daily MaintenanceComponents Resin Pump TroubleshootingSpray pattern Mendations Fluid is too thin or too thick General Information Disconnect the Displacement PumpRepair Align cylinder and adapter plate Reconnect the Displacement PumpReconnect the Air Motor Disconnect the Air MotorTi18456c Replace Pumpline Repair Throat and Piston Seals Repair Catalyst PumpRemove Catalyst Pump from System Disassemble Catalyst PumpAssemble Catalyst Pump Repair Foot ValveCatalyst Pump Details Systems System Parts152 24M692 SPACER, ball joint Wall or Pole Mount KIT Wall or Pole Mount KIT Wall or Pole Mount KIT Quantity CartsSystem Parts Part Description Qty Wall or Pole Mount Kit, 16N918Boom, 16N761 Air Panel Slave Pump Linkage, 16P125 Part Description 131 171 Resin PumplinesCoupling Collars Connecting KitAir Motor and Pump for Resin Pumpline GunMesh Pack Resin Filter24F620 16M736 Resin Supply Hose3A2012J 922 930 940 Catalyst Slave PumpsCatalyst Pumps Installation Tools not shown16P425 Catalyst ReservoirCart not included in kit, shown for reference only Hose Bundles Quantity 16N0169, 16N017, 16N018, and 16N019 Kits Accessory Parts Heater Kits16N014 and 16N015 Kits Nipple Asme Pressure Pots, 2-gallon 16M893 and 5-gallon 16M894 Solvent Pressure Pot KitsTube Asme and CE-Approved Pressure Pots, 16M874 and 16M875Gallon 16M560 and 5-gallon 16M561 Solvent Diaphragm Pumps16M881 DataTrak Upgrade KitCarts for 55 Gallon Barrel, 16M896 16M961 Roving Box BracketFor external gel Extension HosesGel Hose Chop HoseTop View DimensionsCart and Boom Wall/Pole Mount Cart OnlyPumpline Wall Mounting Bracket Dimensions Technical DataPumpline Technical Data 3A2012J Graco Information Graco Standard Warranty