Graco ti18524d, ti18496b, ti18526c Prime/Flush, Counter/Totalizer, Display, Diagnostics

Page 36

Operation

Prime/Flush

1.See FIG. 31. To enter Prime/Flush mode, press any

key to wake up the display, then press . The Prime/Flush symbol will appear in the display and

the LED will flash		.

2.While in Prime/Flush mode, runaway protection is disabled and the batch totalizer (BT) will not count. The grand totalizer (GT) continues to count.

1.To exit Prime/Flush mode, press any key to wake

up the display, then press . The Prime/Flush symbol will disappear from the display and the LED will stop flashing.

Counter/Totalizer

See FIG. 31. The last digit of the batch totalizer (BT) rep- resents tenths of gallons or liters. To reset the totalizer, press any key to wake up the display, then press and

hold for 3 seconds.

•If AC is set to gallons or ounces, BT and GT dis- play gallons.

•If AC is set to liters or cc, BT and GT display liters.

•If AC is set to cycles, BT and GT display cycles.

Press to toggle between flow rate units and cycles. A letter under the BT display indicates that both BT and GT are displaying gallons (g) or liters (l). No letter means both BT and GT are displaying cycles.

Display

See FIG. 31. The display (CF) will turn off after 1 minute of inactivity in Run mode or 3 minutes in Setup mode. Press any key to wake up the display.

NOTE: DataTrak will continue to count cycles when dis- play is off.

NOTE: The display (CF) may turn off if a high-level static discharge is applied to the DataTrak. Press any key to wake up the display.

Diagnostics

DataTrak can diagnose several problems with the pump. When the monitor detects a problem, the LED (CD, See FIG. 31) will flash and a diagnostic code will appear on the display. See Table 1.

To acknowledge the diagnosis and return to the normal

operating screen, press once to wake up the dis- play, and once more to clear the diagnostic code screen

36

3A2012J

Image 36

Contents Important Safety Instructions FRP ProportionerContents Related Manuals Agency ApprovalsManual Description Models No Cart Cart, Mast, and BoomHose Length RatioAccessories Skin Injection Hazard Toxic Fluid or Fumes Hazard 3A2012J Important Two-Component Material Information Material Self-ignitionChanging Materials Keep Resin and Catalyst Components SeparateOverview Typical ApplicationsComponent Identification KeyAir Control Panel Air Motor and Resin Displacement Pump Pressure relief/recirculation valve P relieves presPressure relief/recirculation fluid outlet P1 place Pressurized fluid outlet on filter R connect fluidCatalyst Pump Catalyst Pump ComponentsSolvent Flush Systems Solvent Flush Diaphragm PumpSolvent Flush Asme and CE-Approved Pressure Pot Setup Before InstallationLocation Requirements System Mounting Wall Mount Systems OnlyFor systems bolting directly to wall not using a pole System Assembly For cart and boom systems only, install legsSpring Chain Roving Guides Deflector Plates Ground Wire GroundingConnect Fluid and Air Lines Air ConnectionsCatalyst Pump Pressure Relief Valve Flush Before First Use Fill Supply TanksSolvent Flush Connections if applicable Gun ConnectionsPressure Relief Procedure and Shutdown OperationTrigger Lock Boom OperationOperation Startup For internal mix proportioners only, check solvent lineFollow Pressure Relief Procedure and Shut- down on PrimeOperation 3A2012J Flush Spray External mix systems 30-40 psi 0.21-0.28 MPa, 2.1-2.8 barAAC Air Adjustment Follow Pressure Relief Procedure and Shutdown onRun Mode Setup ModeDataTrak Operation Operation Runaway Monitor Solenoid Release ButtonDiagnostics Prime/FlushCounter/Totalizer DisplayDiagnostic Codes Symbol Code Name Diagnosis Cause Replace DataTrak Battery or Fuse Disconnect DataTrakMaintenance ComponentsTask Schedule Inspect pump wetcup Daily Troubleshooting Resin PumpSpray pattern Mendations Fluid is too thin or too thick Disconnect the Displacement Pump RepairGeneral Information Reconnect the Displacement Pump Align cylinder and adapter plateDisconnect the Air Motor Reconnect the Air MotorTi18456c Replace Pumpline Repair Catalyst Pump Remove Catalyst Pump from SystemDisassemble Catalyst Pump Repair Throat and Piston SealsRepair Foot Valve Assemble Catalyst PumpCatalyst Pump Details System Parts Systems152 24M692 SPACER, ball joint Wall or Pole Mount KIT Wall or Pole Mount KIT Wall or Pole Mount KIT Carts QuantitySystem Parts Wall or Pole Mount Kit, 16N918 Part Description QtyBoom, 16N761 Air Panel Slave Pump Linkage, 16P125 Resin Pumplines Part Description 131 171Connecting Kit Air Motor and Pump for Resin PumplineGun Coupling CollarsResin Filter 24F620Mesh Pack Resin Supply Hose 16M7363A2012J Catalyst Slave Pumps 922 930 940Installation Tools not shown Catalyst PumpsCatalyst Reservoir 16P425Cart not included in kit, shown for reference only Hose Bundles Quantity Accessory Parts Heater Kits 16N014 and 16N015 Kits16N0169, 16N017, 16N018, and 16N019 Kits Nipple Solvent Pressure Pot Kits Asme Pressure Pots, 2-gallon 16M893 and 5-gallon 16M894Asme and CE-Approved Pressure Pots, 16M874 and 16M875 TubeSolvent Diaphragm Pumps Gallon 16M560 and 5-gallon 16M561DataTrak Upgrade Kit 16M881Carts for 55 Gallon Barrel, 16M896 Roving Box Bracket 16M961Extension Hoses Gel HoseChop Hose For external gelDimensions Cart and BoomTop View Cart Only Wall/Pole MountTechnical Data Pumpline Wall Mounting Bracket DimensionsPumpline Technical Data 3A2012J Graco Standard Warranty Graco Information