Graco ti18526c, ti18524d, ti18496b Technical Data, Pumpline Wall Mounting Bracket Dimensions

Page 83

Technical Data

Pumpline Wall Mounting Bracket Dimensions

The pumpline bolts directly to this mounting plate.

WLD

Four 0.60 in. (15 mm) mounting holes

3.52in.

(89.4 mm)

10.1in. (257 mm)

Technical Data

System Technical Data

Maximum fluid working pressure	13:1 Systems: 1300 psi (9 MPa, 90 bar)
	17:1 Systems: 1700 psi (11.9 MPa, 119 bar)
Maximum air inlet pressure	100 psi (0.7 MPa, 7.0 bar)
Maximum air inlet pressure to ASME solvent pressure pots . . .	100 psi (0.7 MPa, 7.0 bar)
Typical flow rate of pattern guns	Refer to RS Gun manual. See Related Manuals, page 3.
Maximum fluid temperature (Models with RS Gun)	100°F (38°C)*
Maximum fluid temperature (Models without RS Gun)	160°F (71°C)*
A component (catalyst) inlet size	3/8 in. tube
B component (resin) inlet size	1 5/16-12 UN-2A male
Wetted parts	Stainless steel, carbide, UHMWPE, PTFE, and acetal.
Resin wetted parts	See Pumpline Technical Data, page 84
Catalyst wetted parts	See Catalyst Pump Technical Data, page 84

*Maximum fluid temperature rating determined by lowest rated component in system.

3A2012J

83

Image 83

Contents FRP Proportioner Important Safety InstructionsContents Manual Description Related ManualsAgency Approvals Length Ratio ModelsNo Cart Cart, Mast, and Boom HoseAccessories Skin Injection Hazard Toxic Fluid or Fumes Hazard 3A2012J Keep Resin and Catalyst Components Separate Important Two-Component Material InformationMaterial Self-ignition Changing MaterialsTypical Applications OverviewKey Component IdentificationAir Control Panel Pressurized fluid outlet on filter R connect fluid Air Motor and Resin Displacement PumpPressure relief/recirculation valve P relieves pres Pressure relief/recirculation fluid outlet P1 placeCatalyst Pump Components Catalyst PumpSolvent Flush Asme and CE-Approved Pressure Pot Solvent Flush SystemsSolvent Flush Diaphragm Pump System Mounting Wall Mount Systems Only SetupBefore Installation Location RequirementsFor systems bolting directly to wall not using a pole For cart and boom systems only, install legs System AssemblySpring Chain Roving Guides Deflector Plates Grounding Ground WireAir Connections Connect Fluid and Air LinesCatalyst Pump Pressure Relief Valve Gun Connections Flush Before First UseFill Supply Tanks Solvent Flush Connections if applicableBoom Operation Pressure Relief Procedure and ShutdownOperation Trigger LockOperation For internal mix proportioners only, check solvent line StartupPrime Follow Pressure Relief Procedure and Shut- down onOperation 3A2012J Flush External mix systems 30-40 psi 0.21-0.28 MPa, 2.1-2.8 bar SprayFollow Pressure Relief Procedure and Shutdown on AAC Air AdjustmentDataTrak Operation Run ModeSetup Mode Operation Solenoid Release Button Runaway MonitorDisplay DiagnosticsPrime/Flush Counter/TotalizerDiagnostic Codes Symbol Code Name Diagnosis Cause Disconnect DataTrak Replace DataTrak Battery or FuseTask Schedule Inspect pump wetcup Daily MaintenanceComponents Resin Pump TroubleshootingSpray pattern Mendations Fluid is too thin or too thick General Information Disconnect the Displacement PumpRepair Align cylinder and adapter plate Reconnect the Displacement PumpReconnect the Air Motor Disconnect the Air MotorTi18456c Replace Pumpline Repair Throat and Piston Seals Repair Catalyst PumpRemove Catalyst Pump from System Disassemble Catalyst PumpAssemble Catalyst Pump Repair Foot ValveCatalyst Pump Details Systems System Parts152 24M692 SPACER, ball joint Wall or Pole Mount KIT Wall or Pole Mount KIT Wall or Pole Mount KIT Quantity CartsSystem Parts Part Description Qty Wall or Pole Mount Kit, 16N918Boom, 16N761 Air Panel Slave Pump Linkage, 16P125 Part Description 131 171 Resin PumplinesCoupling Collars Connecting KitAir Motor and Pump for Resin Pumpline GunMesh Pack Resin Filter24F620 16M736 Resin Supply Hose3A2012J 922 930 940 Catalyst Slave PumpsCatalyst Pumps Installation Tools not shown16P425 Catalyst ReservoirCart not included in kit, shown for reference only Hose Bundles Quantity 16N0169, 16N017, 16N018, and 16N019 Kits Accessory Parts Heater Kits16N014 and 16N015 Kits Nipple Asme Pressure Pots, 2-gallon 16M893 and 5-gallon 16M894 Solvent Pressure Pot KitsTube Asme and CE-Approved Pressure Pots, 16M874 and 16M875Gallon 16M560 and 5-gallon 16M561 Solvent Diaphragm Pumps16M881 DataTrak Upgrade KitCarts for 55 Gallon Barrel, 16M896 16M961 Roving Box BracketFor external gel Extension HosesGel Hose Chop HoseTop View DimensionsCart and Boom Wall/Pole Mount Cart OnlyPumpline Wall Mounting Bracket Dimensions Technical DataPumpline Technical Data 3A2012J Graco Information Graco Standard Warranty