Graco ti18526c Solvent Pressure Pot Kits, Asme Pressure Pots, 2-gallon 16M893 and 5-gallon 16M894

Page 74

System Parts

Solvent Pressure Pot Kits

ASME Pressure Pots, 2-gallon 16M893 and 5-gallon 16M894

2 1307	1311 3
1306	1304 2
2 1310	1305 2
	1305 2
2 1309
2 1303	1302 2
2 1303
	1301 1

1	To assemble strainer (1311), remove the dip tube from tank (1301). Slide
	strainer onto bottom end of dip tube. Hold strainer in place while
	positioning dip tube. Strainer should be secure on ube and pressed to
	bottom of tank. Tighten dip tube in place. Strainer not shown.
2	Apply pipe sealant.
3	Clamp ground cable (1311) to handle on tank (1101). Ground cable not
	shown.

Ref	Part	Description	Qty
1301	20324-00	TANK, solvent, 2 gallon	1
		(assembly 16M893 only)
	20324-01	TANK, solvent, 5 gallon	1
		(assembly 16M894 only)
1302	16D939	FITTING, nipple, reducing	1
1303	11021-23	PLUG, pipe, 1/4	1
1304	18470-05	VALVE, ball, 2-way, 1/4nptf	1
1305	RM-856-04	FITTING, elbow, 1/4 nptm x	1
		1/4 nptm
1306	20655-04	FITTING, elbow, 3/8 nptm x	1
		3/8 tube
1307	103347	VALVE, safety, 100 psi	1
1308	21035-00	STRAINER, pick-up, material	1
1309	21462-01	FITTING, adapter, 1/4 nptm x	1
		3/8 nptf
1310	3165	VALVE, ball, 2-way,	1
		3/8 female, 3/8 male
1311	17440-00	CLAMP, grounding	1

74

3A2012J

Image 74

Contents Important Safety Instructions FRP ProportionerContents Manual Description Related ManualsAgency Approvals Hose ModelsNo Cart Cart, Mast, and Boom Length RatioAccessories Skin Injection Hazard Toxic Fluid or Fumes Hazard 3A2012J Changing Materials Important Two-Component Material InformationMaterial Self-ignition Keep Resin and Catalyst Components SeparateOverview Typical ApplicationsComponent Identification KeyAir Control Panel Pressure relief/recirculation fluid outlet P1 place Air Motor and Resin Displacement PumpPressure relief/recirculation valve P relieves pres Pressurized fluid outlet on filter R connect fluidCatalyst Pump Catalyst Pump ComponentsSolvent Flush Asme and CE-Approved Pressure Pot Solvent Flush SystemsSolvent Flush Diaphragm Pump Location Requirements SetupBefore Installation System Mounting Wall Mount Systems OnlyFor systems bolting directly to wall not using a pole System Assembly For cart and boom systems only, install legsSpring Chain Roving Guides Deflector Plates Ground Wire GroundingConnect Fluid and Air Lines Air ConnectionsCatalyst Pump Pressure Relief Valve Solvent Flush Connections if applicable Flush Before First UseFill Supply Tanks Gun ConnectionsTrigger Lock Pressure Relief Procedure and ShutdownOperation Boom OperationOperation Startup For internal mix proportioners only, check solvent lineFollow Pressure Relief Procedure and Shut- down on PrimeOperation 3A2012J Flush Spray External mix systems 30-40 psi 0.21-0.28 MPa, 2.1-2.8 barAAC Air Adjustment Follow Pressure Relief Procedure and Shutdown onDataTrak Operation Run ModeSetup Mode Operation Runaway Monitor Solenoid Release ButtonCounter/Totalizer DiagnosticsPrime/Flush DisplayDiagnostic Codes Symbol Code Name Diagnosis Cause Replace DataTrak Battery or Fuse Disconnect DataTrakTask Schedule Inspect pump wetcup Daily MaintenanceComponents Troubleshooting Resin PumpSpray pattern Mendations Fluid is too thin or too thick General Information Disconnect the Displacement PumpRepair Reconnect the Displacement Pump Align cylinder and adapter plateDisconnect the Air Motor Reconnect the Air MotorTi18456c Replace Pumpline Disassemble Catalyst Pump Repair Catalyst PumpRemove Catalyst Pump from System Repair Throat and Piston SealsRepair Foot Valve Assemble Catalyst PumpCatalyst Pump Details System Parts Systems152 24M692 SPACER, ball joint Wall or Pole Mount KIT Wall or Pole Mount KIT Wall or Pole Mount KIT Carts QuantitySystem Parts Wall or Pole Mount Kit, 16N918 Part Description QtyBoom, 16N761 Air Panel Slave Pump Linkage, 16P125 Resin Pumplines Part Description 131 171Gun Connecting KitAir Motor and Pump for Resin Pumpline Coupling CollarsMesh Pack Resin Filter24F620 Resin Supply Hose 16M7363A2012J Catalyst Slave Pumps 922 930 940Installation Tools not shown Catalyst PumpsCatalyst Reservoir 16P425Cart not included in kit, shown for reference only Hose Bundles Quantity 16N0169, 16N017, 16N018, and 16N019 Kits Accessory Parts Heater Kits16N014 and 16N015 Kits Nipple Solvent Pressure Pot Kits Asme Pressure Pots, 2-gallon 16M893 and 5-gallon 16M894Asme and CE-Approved Pressure Pots, 16M874 and 16M875 TubeSolvent Diaphragm Pumps Gallon 16M560 and 5-gallon 16M561DataTrak Upgrade Kit 16M881Carts for 55 Gallon Barrel, 16M896 Roving Box Bracket 16M961Chop Hose Extension HosesGel Hose For external gelTop View DimensionsCart and Boom Cart Only Wall/Pole MountTechnical Data Pumpline Wall Mounting Bracket DimensionsPumpline Technical Data 3A2012J Graco Standard Warranty Graco Information