Dynacord PowerMate 600 owner manual Master, Status Indicator

Page 34

MASTER

38. STATUS INDICATOR

These indicators are to inform you about the momentary operational status of the PowerMate’s internal power amplifier.

The PROTECT indicator lights when one of the power amplifier’s extensive protection functions – against thermal overload, HF-induction, DC at the outputs, and SOAR-protection – is activated. When the PowerMate is in protect mode, the speaker outputs are muted and the inputs of the power amplifier are short-circuited to prevent the amplifier from being damaged. In this case you should first check if the frontal and/or rear ventila- tion louvres are blocked. Another cause could be, that you have connected more than three 8ohms speaker systems per power output. Please also disconnect the SPEAKON connectors and check the speaker cables for short circuits.During the power-on operation, the PRO- TECT LED always lights for about two seconds. This

is normal. It indicates that the PowerMate’s protection circuitry is operational.

The LIMIT indicator signals that your operating the PowerMate at the internal amplifier’s limit. Frequent blinking of the LED is acceptable, since the amplifier’s incorporated limiter prevents the occurrence of distorti- on. Continuous lighting indicates that a degradation in the outputted sound is likely to happen. In that case, the master level should be reduced.

The POWER ON indicator is always lit when the PowerMate is in operational mode - i. e. it is switched on. If, after switching on the power, the LED is not lit, please make sure that the PowerMate’s mains cord is plugged in correctly. If this is the case and the LED is still not lit, please contact your dealer.

39. 7-BAND STEREO GRAPHIC EQUALIZER

The PM600’s integrated 7-band stereo graphic equalizer is located in the L/R master channel section. The seven frequency bands - each providing ±10dB amplification/ attenuation - offer the possibility to optimally match the overall sound to the acoustic conditions of different loca- tions or shape it according to your personal taste.

+20

 

 

 

 

 

 

 

 

 

+15

 

 

 

 

 

 

 

 

 

+10

 

 

 

 

 

 

 

 

 

+5

 

 

 

 

 

 

 

 

 

+0

 

 

 

 

 

 

 

 

 

-5

 

 

 

 

 

 

 

 

 

-10

 

 

 

 

 

 

 

 

 

-15

 

 

 

 

 

 

 

 

 

-20

 

 

 

 

 

 

 

 

 

20

50

100

200

500

1k

2k

5k

10k

20k

 

 

 

 

 

Hz

 

 

 

 

34

Image 34
Contents PowerMate Inhalt ContentsTable DES Matières Wichtige Sicherheitshinweise Auspacken und Garantie BeschreibungAufstellen und Anschließen MIC Input MonoLine Einstellhinweis GainKlangregelung AUX Signal / PEAK- AnzeigeVolume PANStereo Input L / Mono R Input StereoLine Trim 13. FX Signal / PeakBAL FX1/FX2 FX1/FX2Umstellung der Effekt-Startprogramme DisplayPeak LED 19. UP/DOWNFX on EinstellhinweiseAUX/MONO Effekt 1/2 Status Anzeige MasterBand Stereo Graphic Equalizer Master LED-DISPLAY Master L + RRückseite PowerSpeaker Outputs Right / Left Symmetrisch Unsymmetrisch Aufbau Einer STANDARD-PAUnsymmetrisch SymmetrischAufbau Soundcheck Monitormix OWNER‘S Manual Contents Important Safety Instructions Installation and Connections DescriptionInput Mono EQ Section Signal / Peak indicator Stereo Input L/MONO R Tone Control SectionSIGNAL/PEAK 13. FX AUX BALChanging FX Start Programs Setting Instructions 19 . UP/DOWNGenerally, the AUX channel is used as monitor bus Effect 1/2 PhonesStatus Indicator Master LED-DISPLAY Rear Panel Speaker Cables STANDARD-PACabling LF-CABLES Balanced or UNBALANCED?Setting up Sound Check Main MIXMonitor MIX Mode D‘EMPLOI Table DES Matières Instructions DE Sécurité Importantes Dynacord Installation et BranchementsIntroduction Déballage et garantieEntrée Mono Line LigneConseils de réglage Section EQ ÉgaliseurIndicateur SIGNAL/PEAK FX EffetsEntrée Stereo Section DE Contrôle DU SON ToneSIGNAL/PEAK Lire le paragraphe «Changer les effets de démarrage» Changer les effets de démarrageInstructions de réglage AfficheurTemoin Peak Effect Return Retour D’EFFETMaster Track Return L/R Retour 2 Pistes Power AMP Inputs Entrées AmplificateurPhones Sortie casques Track Return38. Témoins Indicateurs D‘ÉTAT 39. Égaliseur Graphique Stéréo 7 Bandes40. Échelle DE LED Master Master L+RPanneau Arrière Speaker Outputs RIGHT/LEFT Sorties HP gauche/ droiteCâbles de haut-parleur Installation D‘UN Système DE Sonorisation StandardCâblage Câbles basse fréquence Symétrisés ou non symétrisés ?Installation Sound Check Mixage PrincipalMixage DU Circuit Moniteur Specifications Block Diagram Dimensions Bosch Communications Systems
Related manuals
Manual 64 pages 54.56 Kb