Installation

IMPORTANT

MESSAGE

The Regency Gas Fireplace must be installed in accordance with these instructions. Carefully read all the instructions in this manual ﬁrst.

Note: Failure to follow these instructions could cause a malfunction of the heater which could result in death, serious bodily injury, and/or prop- erty damage. Failure to follow these instructions may also void your ﬁre insurance and/or warranty.

FOR YOUR SAFETY

This appliance requires air for proper combus- tion. Always provide adequate combustion and ventilation air. Follow instructions and informa- tion in the current AS5601-2004, NZS 5261 or local codes. Consult the "authority having jurisdiction" to determine the need for a permit prior to starting the installation.

MATERIALS REQUIRED

A 240 Volt AC power cord is hooked up to the unit. Plug 3 wire cord into a suitable receptacle. Do not cut the ground terminal off under any circumstances.

When connected with 240 volts, the appliance must be electrically grounded in accordance with local codes.

This unit is polarity sensitive and will not oper- ate if polarity is incorrect.

BEFORE YOU START

Installation is to be carried out ONLY by an authorised person.

1)The appliance shall be installed in accord- ance with the manufacturer's installation instructions, local gas ﬁtting regulations, municipal building codes, water supply regulations, electrical wiring regulations, with AS5601-2004. (AGA gas installation code) NZS 5261(New Zealand)

2)Installation and repair should be done ONLY by an authorised person.

3)The appliance should be inspected before use and at least annually by an authorised service person. More frequent cleaning may be required due to excessive lint from carpet- ing, bedding material, etc. It is imperative that control compartments, burners and circulating air passageways of the appliance be kept clean and free from excessive lint from carpeting.

4)See general construction and assembly instructions. This appliance may only be in- stalled in a ﬂued, non-combustible ﬁreplace. The appliance and ﬂue should be enclosed when installed or passing through a living area, where children may come in contact with it.

This appliance can also be installed into the approved Zero Clearance Kit #486-900 in a combustible situation.

5)Always connect this space heater to a chim- ney and ﬂue to the outside of the building envelope. Never ﬂue to another room. Make sure that the ﬂue is properly sized and is of adequate height to provide the proper draft.

6)Inspect the ﬂueing system annually for blockage and any signs of deterioration.

7)Any safety glass removed for servicing must be replaced prior to operating the ap- pliance.

8)To prevent injury, do not allow anyone who is unfamiliar with the operation to use the ﬁreplace.

9)Installer must mechanically attach the sup- plied label to the inside of the ﬁrebox of the ﬁreplace into which the gas ﬁreplace insert is installed.

"WARNING: This ﬁreplace has been converted for use with a gas ﬁreplace insert only and cannot be used for burning wood or solid fuels unless all original parts have been replaced, and the ﬁreplace re-approved by the authority having jurisdiction."

INSTALLATION

CHECKLIST

The Regency Gas Insert is installed as listed below.

1)Unit Location - refer to "Clearances to Combustibles" section.

2)Make the gas connections. Refer to "Gas Connections" section.

3)Install the ﬂue or liner to the ﬂue collar. Refer to "Flueing" section.

4)Slide the unit into the ﬁreplace.

5)Test gas pressure, refer to "Gas Pipe Pres- sure Testing" section. Check aeration, refer to "Aeration Settings" section.

6)Test for ﬂue spillage, refer to "Test for Flue Spillage" section.

7)Install the optional brick panels. Refer to "Optional Brick Panels" section.

8)Install the log set. Refer to "Log Set instal- lation" section.

9)Assemble and install the faceplate and trim and louvres. Refer to "Faceplate, Trim & Louvre" section.

10)Optional Premium Flush Front installation. Refer to "Premium Flush Front Installation" section.

11) Final check: Before leaving this unit with the customer, the installer must ensure that the appliance is ﬁring correctly. This includes:

a)Clocking the appliance to ensure the correct ﬁring rate.

b)Adjusting the primary air, if required, to ensure that the ﬂame does not car- bon.

c)Ensuring that the appliance is ﬂueing correctly. Refer to "Test for Flue Spillage" section.

Regency IG35 Gas Inbuilt Fireplace

IG35-LPG, IG35-ULPG, IG35-NG specifications

The Regency IG35-NG, IG35-ULPG, and IG35-LPG represent a trio of advanced heating solutions designed to cater to various fuel types while maintaining efficiency and user comfort. These units are ideal for modern residences and commercial spaces, showcasing technological advancements in the heating sector.

The IG35-NG operates on natural gas, offering an environmentally friendly solution with lower emissions compared to traditional heating methods. Its ability to provide consistent heat while being energy efficient makes it an attractive option for both new builds and retrofits. Featuring an automatic ignition system, the IG35-NG ensures quick and hassle-free operation, allowing users to enjoy immediate warmth.

For those in regions where propane is more accessible, the IG35-ULPG caters specifically to ultra-low propane gas environments. This model boasts similar performance metrics to the IG35-NG but is optimized for utilizing propane under lower pressure. The advanced burner technology employed in the IG35-ULPG tracks combustion efficiency and significantly reduces fuel consumption, making it both cost-effective and eco-friendly.

The IG35-LPG, on the other hand, is tailored for standard liquefied petroleum gas applications. Ideal for areas lacking natural gas infrastructure, this model ensures that users can still benefit from efficient heating solutions. The IG35-LPG incorporates sophisticated safety features, including flame failure detection and automatic shut-off systems. This ensures peace of mind for users by minimizing risks related to gas leaks and other potential hazards.

All three models share a sleek design, fitting seamlessly into various interior aesthetics. The compact size enhances installation flexibility, allowing these heaters to fit into spaces where traditional heating units may not suffice. Moreover, they come equipped with user-friendly controls that facilitate easy adjustments to temperature settings, ensuring optimal comfort during cold seasons.

In terms of energy efficiency, these heaters carry exceptional ratings, which may even qualify them for rebates and incentives in many regions. The advanced heat exchanger technology employed in these units allows for maximum heat transfer while minimizing waste, thus serving the dual purpose of reducing heating costs and environmental impact.

Overall, the Regency IG35 series presents a versatile and efficient lineup of heating solutions. With their modern technologies, user-centric features, and commitment to safety and efficiency, the IG35-NG, IG35-ULPG, and IG35-LPG represent the next generation of heating for both residential and commercial applications.