Regency IG35-ULPG, IG35-LPG, IG35-NG Aeration Settings, Max. Input, Min. Input, Supply Pressure

Page 8

INSTALLATION

System Data

IG35

TEST FOR FLUE

OPTIONAL

SPILLAGE

BRICK PANEL

IG35-NG: For 0 to 610 meters altitude

IG35-LPG: For 0 to 610 meters altitude

IG35-ULPG: For 0 to 610 meters altitude

Burner Inlet Orifice Sizes:

 

NG

LPG

ULPG

Burner #33

#51

#53

 

 

 

Max. Input

 

 

NG

33.5 mj

 

LPG

34 mj

 

ULPG

28 mj

 

 

 

 

Min. Input

 

 

NG

19.6 mj

 

LPG

18.5 mj

 

ULPG

14 mj

 

 

 

 

Supply Pressure

 

 

NG

1.13 kPa

 

LPG

2.75 kPa

 

ULPG

2.75 kPa

 

 

 

 

Manifold Pressure

 

 

NG

0.87 kPa

 

LPG

2.61 kPa

 

ULPG

2.61 kPa

 

Electrical: 240 V. 50Hz.

Circulation: High/Off/LO speed fan, 150/89 CFM.

Log Set: Ceramic fiber, 7 per set.

Aeration Setting

NG

15mm fully open

LPG

15mm fully open

ULPG

15mm fully open

A " spillage" test must be made before the installed unit is left with the customer. Follow the procedure below:

1)Start all exhaust fans in the home and then close all external doors and windows in the house.

2)Light the unit and set controls to maximum. Turn fan off.

3)After five minutes, test that there is a “pull” on the flue by placing a smoke match, cigarette or similar device which gives off smoke, in both sides of the unit. See diagram 1.

Diagram 1

1)Unwrap the brick panels from the protective wrapping.

2)Remove the glass front and log set if already installed.

3)Place the rear brick panel flat against the back of the unit, by carefully slipping it be- tween the back wall of the firebox and the rear log tray.

4)Remove the screw on the inside top left and right side of the firebox.

LeftSide

ofFirebox

Rem ove screw

5)Slide the left and right side brick panels in place and secure using the brick retaining clips provided and the screws removed in step 4 as shown in the diagram below.

AERATION SETTINGS

The burner aeration is factory set but may need adjusting due to either the local gas supply, air supply or altitude. This adjustment is performed by the installer. (Close the aeration for a more yellow flame, or open it to make the flame bluer).

NG:

15mm fully open

LPG:

15mm fully open

ULPG:

15mm fully open

Note: Any damage due to carboning result- ing from improperly setting the aera- tion controls is NOT covered under warranty.

The smoke should be drawn into the unit. If the smoke is still not drawn into the spill tube, turn the unit off and check for the cause of the lack of draft. If necessary, rectify.

For wind turbulent sites, a wind cap may rem- edy the problem. These caps are not included with the standard flue kit and will need to be purchased separately.

Screw

 

Brick

 

R etaining

 

C lip

Back

 

brick

 

panel

Side

 

 

brick

 

panel

8

Regency IG35 Gas Inbuilt Fireplace

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Manual Please Keep These Instructions For Future ReferenceRegency IG35 Gas Inbuilt Fireplace Unit DimensionsRegency GAS Inbuilt Fireplace Table of Contents Data Badge Installation Minimum Fireplace Dimensions Minimum Clearances to CombustiblesGAS Connection Premium Flush Front FramingGAS Pipe Pressure Testing FlueingAeration Settings Aeration SettingMax. Input Min. InputAntenna Control Box Cover Jumper Location Heat ShieldAdjusting the Outlet Pressure Cable Electric ModulatorConversion Kit #486-967 for NG to Ulpg Installation EmbersEmbers LOG SET InstallationLava Rock With care do not force into position Notch CutoutExample NotchScreen Bracket Slots Faceplate Trim & Louver InstallationDiagram Side Premium Flush Front Installation Faceplate CAT5 CableHeat Defl ector Wire HarnessTab into Tab Bracket Ignition Module Wire Harness RemovedBracket Diagram Regency IG35 Gas Inbuilt Fireplace Hinge Bracket Bottom LouverFinal Check Remote ControlWiring Wiring with Premium Flush Front Option Operating Instructions Copy of Lighting Instruction Plate Normal Operating Sounds GAS AppliancesMaintenance Maintenance InstructionsDoor Glass Replacement LOG ReplacementBack Clip FAN MaintenanceTo Remove Fan Removing Valve Tray 910-084 Parts ListElectronic Components Parts List Description Main AssemblyBurner Assembly & LOG SET Faceplate Assembly Premium Flush Front AssemblyWarranty Warranty LifetimeConditions Exclusions

IG35-LPG, IG35-ULPG, IG35-NG specifications

The Regency IG35-NG, IG35-ULPG, and IG35-LPG represent a trio of advanced heating solutions designed to cater to various fuel types while maintaining efficiency and user comfort. These units are ideal for modern residences and commercial spaces, showcasing technological advancements in the heating sector.

The IG35-NG operates on natural gas, offering an environmentally friendly solution with lower emissions compared to traditional heating methods. Its ability to provide consistent heat while being energy efficient makes it an attractive option for both new builds and retrofits. Featuring an automatic ignition system, the IG35-NG ensures quick and hassle-free operation, allowing users to enjoy immediate warmth.

For those in regions where propane is more accessible, the IG35-ULPG caters specifically to ultra-low propane gas environments. This model boasts similar performance metrics to the IG35-NG but is optimized for utilizing propane under lower pressure. The advanced burner technology employed in the IG35-ULPG tracks combustion efficiency and significantly reduces fuel consumption, making it both cost-effective and eco-friendly.

The IG35-LPG, on the other hand, is tailored for standard liquefied petroleum gas applications. Ideal for areas lacking natural gas infrastructure, this model ensures that users can still benefit from efficient heating solutions. The IG35-LPG incorporates sophisticated safety features, including flame failure detection and automatic shut-off systems. This ensures peace of mind for users by minimizing risks related to gas leaks and other potential hazards.

All three models share a sleek design, fitting seamlessly into various interior aesthetics. The compact size enhances installation flexibility, allowing these heaters to fit into spaces where traditional heating units may not suffice. Moreover, they come equipped with user-friendly controls that facilitate easy adjustments to temperature settings, ensuring optimal comfort during cold seasons.

In terms of energy efficiency, these heaters carry exceptional ratings, which may even qualify them for rebates and incentives in many regions. The advanced heat exchanger technology employed in these units allows for maximum heat transfer while minimizing waste, thus serving the dual purpose of reducing heating costs and environmental impact.

Overall, the Regency IG35 series presents a versatile and efficient lineup of heating solutions. With their modern technologies, user-centric features, and commitment to safety and efficiency, the IG35-NG, IG35-ULPG, and IG35-LPG represent the next generation of heating for both residential and commercial applications.
Top Page Image Contents