Teledyne 3000ZA-3X operating instructions Manual Range Select, Range Setpoints

Page 56

Operation	3000ZA-3X

4.7.2Manual Range Select

-----------------------

Man Rng: R1

-----------------------

Pressing ENTER causes the range R1 or R2 or R3 to start flashing. Then pressing UP or DOWN cycles through the 3 ranges. The selected range is the effective range if the Range Select (above) is set to Man(ual).

4.7.3Range Setpoints

-----------------------

R1: 0-1000.00 ppm

-----------------------

Pressing ENTER causes the value to the right of Rn: to start flashing. Then pressing UP or DOWN adjusts the value. These are the range setpoints for R1, R2, and R3. They may be set to a value in the range of 1.00 ppm to 100% with the stipulation that the each range must have a setpoint equal to or greater than the setpoint of the range below it plus 1ppm.

Teledyne Analytical Instruments

44

Image 56

Contents Model 3000ZA-3X 3000ZA-3X Specific Model Information Important Notice Safety Messages 3000ZA-3X Vii Table of Contents Testing the System Maintenance AppendixModel 3000ZA Front Panel Model 3000ZA Rear PanelList of Tables XiiMain Features of the Analyzer IntroductionOverview Typical ApplicationsModel Designations Introduction 3000ZA-3XFront Panel Operator Interface Model 3000ZA Front PanelFunction Keys Data Entry KeysDigital Meter Display Alphanumeric Interface ScreenStandby Button Access DoorRear Panel Equipment Interface ∙ 50-Pin Equipment Interface Port OptionalOperational Theory IntroductionZrO2 Sensor Principles of OperationSample System Operational Theory 3000ZA-3XElectronics and Signal Processing Zirconium Oxide Sensor Application NotesOperational Theory 3000ZA-3X Component Location Electronic Block Diagram Mounting the Analyzer InstallationUnpacking the Analyzer Installation 3000ZA-3X Rear Panel Connections Gas ConnectionsInstallation3000ZA-3X Zero in and Span in Optional Electrical ConnectionsEquipment Interface Connector Pin Arrangement Threshold Alarm Analog Output ConnectionsSystem Alarm Alarm Relay Contact PinsRemote Calibration Connections Range ID Relay Connections Remote Probe Connections FET Series Resistance 2.3 RS-232 PortCommands via RS-232 Input Installing the Zirconium Oxide Sensors Testing the SystemOperation Keys Description Using the Data Entry and Function ButtonsStyle Conventions Enter EscapeSystem Menu Menu/Screen StructureAnalyze Screen Hierarchy of Available Functions Password routine Enter Password T aChange Password Enter New Password T aLogout Routine Model RoutineFilter Routine Analog-Out Adjust RoutineSelf-Test Routine 20mA Gain 20mA Limit False Track in Cal Yes Change Stream Auto-Calibration TimerSpan Menu Span Value Span TimerSpan Sensor Span Finish Span Auto FinishSpan Begin Span Begin Begin Span?Zero Value Zero MenuZero Finish Zero Timer Zero Timer 7 minZero Begin Zero Begin Begin Zero?Alarms Menu Alarm ActiveAlarm Polarity AL-1 NON-LATCHING AL-1 20.00 ppm AL-2 ActiveAlarm Failsafe Alarm LatchingAlarm Setpoint AL-1 80.00 ppmRange Select Auto Range MenuRange Select Manual Range Select Range SetpointsMaintenance Routine MaintenanceSensor Replacement Removing the SensorMaintenance 3000ZA-3X Fuse Replacement Sensor Block with Middle Sensor InstalledSystem Self Diagnostic Test Self-Test Result DisplayMajor Internal Components Rear Panel Removal Remove only those screws marked with anCleaning TroubleshootingTrace Oxygen Analyzer Maintenance Maintenance 3000ZA-3X Teledyne Analytical Instruments Specifications AppendixOperating Temperature 5-35 C Recommended 2-Year Spare Parts List Qty Part Number DescriptionDrawing List 19-inch Relay Rack Panel MountApplication Notes Flow Rate RecommendationsRestriction Devices BY-PASS Conversions