Teledyne 3000ZA-3X operating instructions Menu/Screen Structure, Analyze Screen, System Menu

Page 42

Operation

3000ZA-3X

 

 

 

4.2.2.4SPECIAL FUNCTION KEYS

Pressing any of the 7 Function keys (ANALYZE / SYSTEM / SPAN / ZERO / ALARMS /RANGE / STANDBY) Cause the display to show the top level menu for the respective function. If another menu operation was being performed, any modified parameters (that had not yet been accepted by using the ENTER key) will be discarded and replaced by the original values.

4.3 Menu/Screen Structure

The 3000 screen setup consists of several classes of screens and items. No item occupies more than 1 line. It is important to read and understand the NAVIGATION AND DATA ENTRY section to fully understand the menu structure.

4.3.1 Analyze Screen

The ANALYSIS SCREEN displays the following:

Line 1:

-The O2 concentration in ppm or '%' (percent)

-If in Span calibration the message "SPAN".

-If in Zero calibration the message "ZERO".

-Otherwise, the message "ANLZ".

Line 2 (display mode 1):

-If Alarm 1 is alarming, the message "AL-1".

-If Alarm 2 is alarming, the message "AL-2".

-If in Range 1 the message "R1: 0-nnnn.nnppm".

-If in Range 2 the message "R2: 0-nnnn.nnppm".

-If in Range 3 the message "R3: 0-nnnn.nnppm".

-or, if range is in percent, "Rx: 0-nnn.nn%".

4.3.2System Menu

The SYSTEM screen can be accessed by pressing the SYSTEM key and it has the following functions:

Teledyne Analytical Instruments

30

Image 42
Contents Model 3000ZA-3X 3000ZA-3X Specific Model Information Important Notice Safety Messages 3000ZA-3X Vii Table of Contents Testing the System Maintenance AppendixModel 3000ZA Front Panel Model 3000ZA Rear PanelList of Tables XiiOverview Main Features of the AnalyzerIntroduction Typical ApplicationsModel Designations Introduction 3000ZA-3XFront Panel Operator Interface Model 3000ZA Front PanelDigital Meter Display Function KeysData Entry Keys Alphanumeric Interface ScreenAccess Door Rear Panel Equipment InterfaceStandby Button ∙ 50-Pin Equipment Interface Port OptionalZrO2 Sensor Operational TheoryIntroduction Principles of OperationSample System Operational Theory 3000ZA-3XElectronics and Signal Processing Zirconium Oxide Sensor Application NotesOperational Theory 3000ZA-3X Component Location Electronic Block Diagram Installation Unpacking the AnalyzerMounting the Analyzer Installation 3000ZA-3X Rear Panel Connections Gas ConnectionsInstallation3000ZA-3X Zero in and Span in Optional Electrical ConnectionsEquipment Interface Connector Pin Arrangement Threshold Alarm Analog Output ConnectionsSystem Alarm Alarm Relay Contact PinsRemote Calibration Connections Range ID Relay Connections Remote Probe Connections FET Series Resistance 2.3 RS-232 PortCommands via RS-232 Input Installing the Zirconium Oxide Sensors Testing the SystemOperation Using the Data Entry and Function Buttons Style ConventionsKeys Description Enter EscapeMenu/Screen Structure Analyze ScreenSystem Menu Hierarchy of Available Functions Change Password Password routineEnter Password T a Enter New Password T aLogout Routine Model RoutineAnalog-Out Adjust Routine Self-Test RoutineFilter Routine 20mA Gain 20mA Limit False Track in Cal Yes Auto-Calibration Timer Span MenuChange Stream Span Timer Span SensorSpan Value Span Begin Span FinishSpan Auto Finish Span Begin Begin Span?Zero Menu Zero FinishZero Value Zero Begin Zero TimerZero Timer 7 min Zero Begin Begin Zero?Alarm Polarity Alarms MenuAlarm Active AL-1 NON-LATCHING AL-1 20.00 ppm AL-2 ActiveAlarm Setpoint Alarm FailsafeAlarm Latching AL-1 80.00 ppmRange Menu Range SelectRange Select Auto Manual Range Select Range SetpointsSensor Replacement MaintenanceRoutine Maintenance Removing the SensorMaintenance 3000ZA-3X Fuse Replacement Sensor Block with Middle Sensor InstalledSystem Self Diagnostic Test Self-Test Result DisplayMajor Internal Components Rear Panel Removal Remove only those screws marked with anCleaning TroubleshootingTrace Oxygen Analyzer Maintenance Maintenance 3000ZA-3X Teledyne Analytical Instruments Specifications AppendixOperating Temperature 5-35 C Recommended 2-Year Spare Parts List Qty Part Number DescriptionDrawing List 19-inch Relay Rack Panel MountApplication Notes Flow Rate RecommendationsRestriction Devices BY-PASS Conversions