Pelco C1300M-C (11/08) manual Azimuth Zero

Page 25

PELCO EXSITE IPSXM

LANGUAGE				ENGLISH
UNIT INVERSION				OFF
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<UNIT SETTINGS>
<POSITION CALIBRATION>
RESET CAMERA
CYCLE CAMERA POWER
REBOOT SYSTEM
EXIT


UNIT SETTINGS

<CAMERA>
<MOTION>
<POWER UP>
<LINE SYNC>
<PRESETS>
<PATTERNS>
<ZONES>
<WINDOW BLANKING>
<ALARMS>
<WIPER>
<AUX>
<CLEAR>
<PASSWORD>
BACK
EXIT


MOTION

PROPORTIONAL PAN				ON
PARK TIME (MINUTES)				0
PARK ACTION				NONE
SCAN SPEED (DEG/S)				25
PRESET FREEZE FRAME				AUTO
LIMIT STOPS				ON
<SET MANUAL STOPS>
<CLEAR MANUAL STOPS>
<SET SCAN STOPS>
<CLEAR SCAN STOPS>

<SET AZIMUTH ZERO>
<CLEAR AZIMUTH ZERO>
BACK
EXIT
REFERENCE INFORMATION
MANUAL LIMITS SET				NO
SCAN LIMITS SET				NO

AZIMUTH ZERO

Azimuth is the pan angle from 0 to 359 degrees. Azimuth zero is the pan position you specify to be the 0-degree point. Azimuth zero is normally set to magnetic north. Once set, azimuth and compass readings are based on the set Azimuth Zero point.

To program azimuth zero:

1.Use the joystick to position the cursor beside SET AZIMUTH ZERO.

2.Press Iris Open.

3.Follow the directions displayed on the monitor.

To clear azimuth zero:

1.Use the joystick to position the cursor beside CLEAR AZIMUTH ZERO.

2.Press Iris Open.

3.Follow the directions displayed on the monitor.

Quick Programming Guide

(See Page 9)

C1300M-C (11/08)

25

Image 25

Contents ExSite Series Explosionproof Positioning System Page Contents Specifications Radio and Television Interference Regulatory NoticesWelcome Configure DoneModels Getting StartedHow to Operate Your System KBD200A/KBD300A Direct Mode only Accessing Main Menu PresetKBD4000/KBD4002 Genex Multiplexer Quick Start Guide System Setup C1300M-C 11/08 Language Unit Inversion OFF default Use for normal installations refer to FigureSystem Information Display Setup Label Positions Camera Unit SettingsDark IR CUT Filter 23X DAY/NIGHT CameraShutter Speed Advanced Camera SettingsAGC Limit Auto Sharpness Auto IrisAuto White Balance GainVideo Level Backlight Compensation BLCWide Dynamic Range 23X DAY/NIGHT Camera NormalMotion There are two proportional pan modes On defaultProportional PAN Amount of zoomPark Time There are three preset freeze frame settings Preset Freeze FrameScan Speed Image is never frozenManual Limit StopsScan Limit stop is reachedAzimuth Zero Power UP Action Power UPNone Line Sync Phase settings range from 0-359 degreesSystem synchronizes to an internal clock Presets Edit Detection Areas 23X DAY/NIGHT Camera Enable Motion Detection 23X DAY/NIGHT CameraTriggers a command to AUX Activate AUX Command 23X DAY/NIGHT CameraAUX Time 23X DAY/NIGHT Camera Patterns Zones To set a window blanking area Window BlankingReverse Available OFF default No blankingClear Window Blank ALL ABOVE/BLANK ALL belowReset Delay AlarmsResume SequenceMEDIUM/LOW Normally open Wiper Wiper ModeWiper Control Wiper DwellSET Washer Sequence AUX When the dwell time is finishedReceived from the controller LatchingClear Password Position Calibration Reset Camera Reset, Cycle Power, RebootCycle Camera Power Reboot SystemUpload Icon Software/Language File UploadNTSC, PAL SpecificationsNtsc PALProduct Warranty and Return Information