Pelco C1300M-C (11/08) manual Quick Start Guide System Setup

Quick Start Guide: System Setup

PELCO EXSITE IPSXM

Quick Programming Guide

LANGUAGE

UNIT INVERSION

Access the main menu (preset 95). See the Accessing

<SYSTEM INFORMATION>

Main Menu (Preset 95) section.

<DISPLAY SETUP>

<UNIT SETTINGS>

Presets

<POSITION CALIBRATION>

Use the joystick to position the cursor beside

The following presets are reserved for special functions.

RESET CAMERA

menu selection. If your controller does not have a

CYCLE CAMERA POWER

joystick, use the up or down key.

Preset

Function

REBOOT SYSTEM

Press Iris Open; the submenu/cursor moves to the right.

33

Flip command (disabled)

EXIT

86

Wiper

87

Washer

88

IR filter IN (color)

Move the joystick up or down to view selections.

89

IR filter OUT (black-white)

If your controller does not have a joystick, use the

90-91

Manual limit stops

up or down key.

92-93

Scan limit stops

ADDITIONAL

SYSTEM INFORMATION

DISPLAY SETUP

LABEL POSITION

UNIT SETTINGS

POSITION CALIBRATION

95

Select main programming menu

FREE MEMORY

UNIT MODEL

PRESET LABEL

[ZONE LABEL- - - - - - - -]

<CAMERA>

PRESET NOT DEFINED

Press Iris Open to make selection.

96

Stop a scan

LAST RESET

POWER MODULE MEMORY

ZONE LABEL

[PRESET LABEL- - - ---]

<MOTION>

<EDIT PRESET SCENE>

97

Random scanning

AZIMUTH ZERO OFFSET

SOFTWARE VERSION

ZOOM

[ALARM 1- - - - - - -]

<POWER UP>

MOTOR ACTIVE

BIOS VERSION

AZMUTH/ELEVATION

<LINE SYNC>

98

Frame scanning

CAMERA ACTIVE

FONT VERSION

DIRECTION

SAVE AND EXIT

<PRESETS>

<CLEAR CALIBRATION PRESET>

99

Start auto scanning

FPGA VERSION

ALARM MESSAGE

CANCEL AND EXIT

<PATTERNS>

<RECAL USING CAL PRESET>

Press Iris Close to cancel selection.

VIDEO LEVEL

COMM

HELP

<ZONES>

NOTE: For American Dynamics controllers with only 32 presets, switch SW3-1

CAMERA

D ADDRESS

<LABEL POSITION>

<WINDOW BLANKING>

BACK

on the dome drive to the ON position. When SW3-1 is ON, preset

<EAB>

P ADDRESS

RESTORE FACTORY DEFAULTS

XXX/-XXX

<ALARMS>

EXIT

99 becomes 32

92 becomes 25

<PMAB>

CM9500 MODE

BACK

NE

<WIPER>

LANGUAGE 1

32 PRESET MODE

XXX.XXX

<AUX>

REFERENCE INFORMATION

98 becomes 31

91 becomes 24

PROTOCOL

EXIT

<CLEAR>

AZIMUTH

97 becomes 30

90 becomes 23

LANGUAGE 2

<PASSWORD>

ELEVATION

LANGUAGE 3

<ADDITIONAL>

96 becomes 29

89 becomes 22

LANGUAGE 4

BACK

ZOOM

95 becomes 28

88 becomes 21

LANGUAGE 5

LANGUAGE 6

BACK

EXIT

93 becomes 26

BACK

EXIT

If the limit stops are turned off, presets 23-26 can be used as regular presets.

EXIT

CAMERA

MOTION

POWER UP

LYNE SYNC

PRESETS

PATTERNS

ZONES

WINDOW BLANKING

ALARMS

WIPER**

AUX

CLEAR

PASSWORD

TYPE OF LIGHTING

PROPORTIONAL PAN

POWER UP ACTION

LINE SYNC

PRESET NUMBER

PATTERN NUMBER

ZONE NUMBER

STYLE

RESUME

WIPER CONTROL

AUX 1 MODE

CLEAR ALL ZONES

ENABLE PASSWORD

AUTO FOCUS

PARK TIME (MINUTES)

LINE SYNC PHASE

PRESET NOT DEFINED

<PROGRAM PATTERN>

ZONE NOT DEFINED

BLANK ALL ABOVE

SEQUENCE (SECS)

WIPER MODE

DWELL TIME (SECS)

CLEAR ALL PRESETS

<EDIT PASSWORD>

ZOOM LIMIT

PARK ACTION

BACK

<CLEAR PATTERN>

RESET DELAY (SECS)

WIPER DWELL (SECS)

CLEAR ALL PATTERNS

ZOOM SPEED

SCAN SPEED (DEG/S)

EXIT

BACK

<EDIT PRESET LABEL>

<EDIT ZONE LABEL>

BLANK ALL BELOW

WIPER TIME (MIN)

AUX 2 MODE

CLEAR ALL WINDOW BLANKING

BACK

LOW LIGHT LEVEL

PRESET FREEZE FRAME

EXIT

BACK

<ALARM SETTINGS>

DWELL TIME (SECS)

EXIT

IR CUT FILTER*

LIMIT STOPS

<EDIT PRESET SCENE>

EXIT

<EDIT ZONE>

<SET WINDOWS>

<SET WASHER SEQUENCE>

RESTORE FACTORY DEFAULTS

AUTO IR LEVEL*

<SET MANUAL STOPS>

<EDIT CAMERA SETTINGS>

ZONE ENABLED

BACK

BACK

BACK

BACK

<CLEAR MANUAL STOPS>

<MOTION DETECTION>*

REFERENCE INFORMATION

ZONE BLANKING

EXIT

BACK

EXIT

<ADVANCED SETTINGS>

<SET SCAN STOPS>

<CLEAR PRESETS>

PATTERN USAGE

EXIT

EXIT

EXIT

<CLEAR SCAN STOPS>

REMAINING

<CLEAR ZONE>

BACK

<SET AZIMUTH ZERO>

<CLEAR CAMERA SETTINGS>

EXIT

<CLEAR AZIMUTH ZERO>

BACK

BACK

EXIT

BACK

EXIT

EXIT

ADVANCED SETTINGS

MOTION DETECTION*

SET WINDOWS

ALARM SETTINGS

SET WASHER SEQUENCE

SHUTTER SPEED

MOTION DETECTION ENABLED

WINDOW NUMBER

ALARM NUMBER

PRESET NOT DEFINED

EDIT THE PASSWORD

AGC LIMIT

<EDIT DETECTION AREA>

<EDIT WINDOW LOCATION>

ALARM PRIORITY

- - - - - - - - - - - - - - - - -

AUTO IRIS

ACTIVATE AUX

<EDIT PRESET LABEL>

1234567890

OK

AUTO IRIS LEVEL

<EDIT WINDOW ZOOM>

ALARM ACTION

<EDIT PRESET SCENE>

ABCDEFGHIJ

CANCEL

AUTO IRIS PEAK

AUX TIME

ENABLE WINDOW

ACTIVATE AUX

<EDIT CAMERA SETTINGS>

KLMNOPQRST

AUTO SHARPNESS

BACK

ALARM CONTACT

UZWXYZ.,-/

SPACE

SHARPNESS LEVEL

REVERSE

WASHER TIME (SECS)

abcdefghij

BACKSPACE

AUTO WHITE BALANCE

EXIT

CLEAR WINDOW

BACK

WIPER DELAY (SECS)

klmnopqrst

R GAIN

BACK

EXIT

AUTO RETURN

uvwxyz*;:

B GAIN

BACKLIGHT COMP

EXIT

<CLEAR PRESET>

VIDEO LEVEL

<CLEAR CAMERA SETTINGS>

WIDE DYNAMIC RANGE*

BACK

BACK

EXIT

EXIT

EDIT DETECTION AREA*

DETECTION AREA 1

LOCATION

SENSITIVITY

DETECTION AREA 2

LOCATION

SENSITIVITY

DETECTION AREA 3

LOCATION

SENSITIVITY

DETECTION AREA 4

LOCATION

SENSITIVITY

* Available only with the 23X day/night camera.	BACK
** Available only with wiper models.	EXIT

C1300M-C (11/08) 9