Pelco C1300M-C (11/08) manual Accessing Main Menu Preset, KBD200A/KBD300A Direct Mode only

Page 8

ACCESSING MAIN MENU (PRESET 95)

You can call up the main menu on your monitor by programming (setting or creating) preset 95 (preset 28 if in AD32-preset mode).

Programming preset 95 for Pelco’s controllers varies according to the type of controller you are using. Instructions for programming preset 95 are given below for various Pelco controllers.

CM6700/CM6800

1.Enter the number of the IPSXM system and press the CAM key.

2.Enter 95 and hold the PRESET key for two seconds.

3.In the Edit Preset menu, arrow to SET and press the ACK key. The main menu appears.

KBD200A/KBD300A (DIRECT MODE ONLY)

1.Enter 95.

2.Hold the PRESET key (approximately five seconds) until the main menu appears on the screen.

CM9500

1.Enter the number of the IPSXM system and press the CAM key. The Main menu appears.

2.Highlight SETUP in the Main menu and press the SELECT key.

3.Highlight CAM in the Setup menu and press the SELECT key.

4.Highlight PRESET in the Camera menu and press the SELECT key.

5.Enter 95 and press the F1 key. The main menu appears.

CM9740/CM9760/CM9770/CM9780

1.Press the ESCAPE key to open the Main menu. Select DEF. The Define Submenu appears.

2.Enter your four-digit PIN if this is your first time entering this mode.

3.Enter 95 and select PRST. The main menu appears on the monitor.

4.Select the Quit icon to return to the default menu.

KBD4000/KBD4002 (GENEX MULTIPLEXER)

1.Press the SPOT MONITOR key.

2.Enter the number of the IPSXM system and press the CAM key.

3.Enter 95, then hold the PRESET key (approximately five seconds) until the main menu appears on the screen.

MPT9500

Standard Coaxitron Mode

1.Enter 95 and press the PRESET SET key.

2.Position the asterisk in the YES row and press the F1 key. The main menu appears.

Extended Coaxitron or RS-485 Mode

1.Enter 95 and press the PRESET SET key.

2.Press the F2 key. The main menu appears.

PelcoNet

1.Check the Set box.

2.Click the preset 95 button. The main menu appears.

8

C1300M-C (11/08)

Image 8
Contents ExSite Series Explosionproof Positioning System Page Contents Specifications Regulatory Notices Radio and Television InterferenceConfigure Done WelcomeModels Getting StartedHow to Operate Your System KBD4000/KBD4002 Genex Multiplexer Accessing Main Menu PresetKBD200A/KBD300A Direct Mode only Quick Start Guide System Setup C1300M-C 11/08 Language OFF default Use for normal installations refer to Figure Unit InversionSystem Information Display Setup Label Positions Unit Settings CameraIR CUT Filter 23X DAY/NIGHT Camera DarkAGC Limit Advanced Camera SettingsShutter Speed Auto Iris Auto SharpnessAuto White Balance GainBacklight Compensation BLC Video LevelWide Dynamic Range 23X DAY/NIGHT Camera NormalThere are two proportional pan modes On default MotionProportional PAN Amount of zoomPark Time Preset Freeze Frame There are three preset freeze frame settingsScan Speed Image is never frozenLimit Stops ManualScan Limit stop is reachedAzimuth Zero None Power UPPower UP Action System synchronizes to an internal clock Phase settings range from 0-359 degreesLine Sync Presets Enable Motion Detection 23X DAY/NIGHT Camera Edit Detection Areas 23X DAY/NIGHT CameraAUX Time 23X DAY/NIGHT Camera Activate AUX Command 23X DAY/NIGHT CameraTriggers a command to AUX Patterns Zones Window Blanking To set a window blanking areaAvailable OFF default No blanking ReverseClear Window Blank ALL ABOVE/BLANK ALL belowAlarms Reset DelayResume SequenceMEDIUM/LOW Normally open Wiper Mode WiperWiper Control Wiper DwellSET Washer Sequence When the dwell time is finished AUXReceived from the controller LatchingClear Password Position Calibration Reset, Cycle Power, Reboot Reset CameraCycle Camera Power Reboot SystemSoftware/Language File Upload Upload IconSpecifications NTSC, PALNtsc PALProduct Warranty and Return Information