Pelco C1300M-C (11/08) manual Normally open

Page 37

PELCO EXSITE IPSXM

LANGUAGE

ENGLISH

 

UNIT INVERSION

OFF

 

<SYSTEM INFORMATION>

 

 

<DISPLAY SETUP>

 

 

<UNIT SETTINGS>

 

 

<POSITION CALIBRATION>

 

 

RESET CAMERA

 

 

CYCLE CAMERA POWER

 

 

REBOOT SYSTEM

 

 

EXIT

 

 

 

 

 

 

 

 

 

 

 

 

 

UNIT SETTINGS

 

 

 

 

 

<CAMERA>

 

 

<MOTION>

 

 

<POWER UP>

 

 

<LINE SYNC>

 

 

<PRESETS>

 

 

<PATTERNS>

 

 

<ZONES>

 

 

<WINDOW BLANKING>

 

 

<ALARMS>

 

 

<WIPER>

 

 

<AUX>

 

 

<CLEAR>

 

 

<PASSWORD>

 

 

BACK

 

 

EXIT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ALARMS

 

 

 

 

 

 

 

 

 

 

 

RESUME

OFF

 

SEQUENCE (SECS)

5

 

RESET DELAY (SECS)

 

 

<ALARM SETTINGS>

 

 

BACK

 

 

EXIT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ALARM SETTINGS

ALARM NUMBER

1

ALARM PRIORITY

LOW

ALARM ACTION

NONE

ACTIVATE AUX

NO

ALARM CONTACT

OFF

BACK

 

EXIT

 

5.Set the auxiliary to activate:

a.Use the joystick to position the cursor beside ACTIVATE AUX.

b.Press Iris Open. The cursor moves to the right.

c.Move the joystick up or down to view the following available selections.

NO (default)

Not activated.

1

An alarm action will activate AUX 1.

2

An alarm action will activate AUX 2.

d.Press Iris Open to enter selection.

NOTE: The AUX 1/AUX2 will stop when all the alarms assigned to it have cleared. If the AUX1/AUX is set up as momentary, then it will be activated each time a new alarm is activated.

6.Set the alarm contact:

a.Use the joystick to position the cursor beside ALARM CONTACT.

b.Press Iris Open. The cursor moves to the right.

c.Move the joystick up or down to view the following available selections.

OFF (default)

Disabled

N/O

Normally open

N/C

Normally closed

d.Press Iris Open to enter selection.

Quick Programming Guide

(See Page 9)

C1300M-C (11/08)

37

Image 37
Contents ExSite Series Explosionproof Positioning System Page Contents Specifications Radio and Television Interference Regulatory NoticesWelcome Configure DoneModels Getting StartedHow to Operate Your System KBD200A/KBD300A Direct Mode only Accessing Main Menu PresetKBD4000/KBD4002 Genex Multiplexer Quick Start Guide System Setup C1300M-C 11/08 Language Unit Inversion OFF default Use for normal installations refer to FigureSystem Information Display Setup Label Positions Camera Unit SettingsDark IR CUT Filter 23X DAY/NIGHT CameraShutter Speed Advanced Camera SettingsAGC Limit Auto Sharpness Auto IrisAuto White Balance GainVideo Level Backlight Compensation BLCWide Dynamic Range 23X DAY/NIGHT Camera NormalMotion There are two proportional pan modes On defaultProportional PAN Amount of zoomPark Time There are three preset freeze frame settings Preset Freeze FrameScan Speed Image is never frozenManual Limit StopsScan Limit stop is reachedAzimuth Zero Power UP Action Power UPNone Line Sync Phase settings range from 0-359 degreesSystem synchronizes to an internal clock Presets Edit Detection Areas 23X DAY/NIGHT Camera Enable Motion Detection 23X DAY/NIGHT CameraTriggers a command to AUX Activate AUX Command 23X DAY/NIGHT CameraAUX Time 23X DAY/NIGHT Camera Patterns Zones To set a window blanking area Window BlankingReverse Available OFF default No blankingClear Window Blank ALL ABOVE/BLANK ALL belowReset Delay AlarmsResume SequenceMEDIUM/LOW Normally open Wiper Wiper ModeWiper Control Wiper DwellSET Washer Sequence AUX When the dwell time is finishedReceived from the controller LatchingClear Password Position Calibration Reset Camera Reset, Cycle Power, RebootCycle Camera Power Reboot SystemUpload Icon Software/Language File UploadNTSC, PAL SpecificationsNtsc PALProduct Warranty and Return Information