Pelco C1300M-C (11/08) manual Welcome, Models, Getting Started, SET the Calibration Point

Page 6

Welcome

Thank you for purchasing Pelco’s ExSite™ IPSXM Series explosionproof positioning system. Your new system features a high resolution, camera/optics package with programmable software.

This manual is designed to be a reference tool for the operation and programming of your system. Inside you will find information about the features and commands of your IPSXM system, as well as a detailed menu tree.

MODELS

IPSXM30C22-2 Pan and tilt system with color camera, 60 Hz, 24 VAC

IPSXM30C22-2X Pan and tilt system with color camera, 50 Hz, 24 VAC

IPSXM31C22-2 Same as IPSXM30C22-2, except supplied with window wiper

IPSXM31C22-2X Same as IPSXM30C22-2X, except supplied with window wiper

IPSXM30CBW23-2 Pan and tilt system with day/night camera, 60 Hz, 24 VAC

IPSXM30CBW23-2X Pan and tilt system with day/night camera, 50 Hz, 24 VAC

IPSXM31CBW23-2 Same as IPSXM30CBW23-2, except supplied with window wiper

IPSXM31CBW23-2X Same as IPSXM30CBW23-2X, except supplied with window wiper

IPSXM30C22-7 Pan and tilt system with color camera, 60 Hz, 90-264 VAC

IPSXM30C22-7X Pan and tilt system with color camera, 50 Hz, 90-264 VAC

IPSXM31C22-7 Same as IPSXM30C22-7, except supplied with window wiper

IPSXM31C22-7X Same as IPSXM30C22-7X, except supplied with window wiper

IPSXM30CBW23-7 Pan and tilt system with day/night camera, 60 Hz, 90-264 VAC

IPSXM30CBW23-7X Pan and tilt system with day/night camera, 50 Hz, 90-264 VAC

IPSXM31CBW23-7 Same as IPSXM30CBW23-7, except supplied with window wiper

IPSXM31CBW23-7X Same as IPSXM30CBW23-7X, except supplied with window wiper

GETTING STARTED

You will need to install your system before using this manual. Refer to the installation manuals for instructions. Once installed apply power to the system. The system will begin a configuration sequence that starts with a limited back and forth pan motion (wiggling) for 2.5 minutes. The limited pan motion is a built-in safety feature to warn anyone at the installation site that the unit is on and to avoid contact with the unit during start up. To stop the limited pan motion press Iris Close. The system will continue its configuration sequence. When the system is done, the following information is displayed:

Pelco ExSite IPSXM

Version X.XX

D Address: 1

P Address: 2

Comm 2400, N, 8, 1

CONFIGURE DONE

This information will remain on the monitor until system operation begins. Refer to the following pages to learn how to operate and program your IPSXM Series positioning system.

DANGER: Do not connect the power module to a supply circuit unless all ExSite system components (pan and tilt, camera module and power module) are installed.

SET THE CALIBRATION POINT

Before programming presets, patterns, zones, labels, and window blanking, program and document the position calibration point (refer to Position Calibration). The purpose of the calibration point is to restore all programmed settings quickly in the event the unit is replaced or refurbished.

6

C1300M-C (11/08)

Image 6
Contents ExSite Series Explosionproof Positioning System Page Contents Specifications Regulatory Notices Radio and Television InterferenceModels Configure DoneWelcome Getting StartedHow to Operate Your System Accessing Main Menu Preset KBD200A/KBD300A Direct Mode onlyKBD4000/KBD4002 Genex Multiplexer Quick Start Guide System Setup C1300M-C 11/08 Language OFF default Use for normal installations refer to Figure Unit InversionSystem Information Display Setup Label Positions Unit Settings CameraIR CUT Filter 23X DAY/NIGHT Camera DarkAdvanced Camera Settings Shutter SpeedAGC Limit Auto White Balance Auto IrisAuto Sharpness GainWide Dynamic Range 23X DAY/NIGHT Camera Backlight Compensation BLCVideo Level NormalProportional PAN There are two proportional pan modes On defaultMotion Amount of zoomPark Time Scan Speed Preset Freeze FrameThere are three preset freeze frame settings Image is never frozenScan Limit StopsManual Limit stop is reachedAzimuth Zero Power UP Power UP ActionNone Phase settings range from 0-359 degrees Line SyncSystem synchronizes to an internal clock Presets Enable Motion Detection 23X DAY/NIGHT Camera Edit Detection Areas 23X DAY/NIGHT CameraActivate AUX Command 23X DAY/NIGHT Camera Triggers a command to AUXAUX Time 23X DAY/NIGHT Camera Patterns Zones Window Blanking To set a window blanking areaClear Window Available OFF default No blankingReverse Blank ALL ABOVE/BLANK ALL belowResume AlarmsReset Delay SequenceMEDIUM/LOW Normally open Wiper Control Wiper ModeWiper Wiper DwellSET Washer Sequence Received from the controller When the dwell time is finishedAUX LatchingClear Password Position Calibration Cycle Camera Power Reset, Cycle Power, RebootReset Camera Reboot SystemSoftware/Language File Upload Upload IconNtsc SpecificationsNTSC, PAL PALProduct Warranty and Return Information