Emerson 4500 manual Appendix a Reference Data, Performance Specifications

Page 55

Reference Manual

00809-0100-4027, Rev AA December 2005

Rosemount 4500

Appendix A

Reference Data

SPECIFICATIONS

Performance Specifications

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page A-1 Dimensional Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . page A-5 Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page A-8

For zero-based spans, reference conditions, Neobee M-20 oil fill, SST materials, 11/2 in. tri-clamp process connections, digital trim values set to equal range points.

Conformance to specification (±3 Sigma)

Technology leadership, advanced manufacturing techniques and statistical process control ensure specification conformance to at least ±3 sigma.

Reference Accuracy

Includes the effects of terminal based linearity, hysteresis, and repeatability.

±0.15% of calibrated span (CS) from 1:1 to 15:1 rangedown

±0.01 --------------URL% of calibrated span from 15:1 to 50:1 rangedown on Range 1 GP

Span

Long Term Stability

0.1% of Upper Range Limit (URL) for 3 years under normal operating conditions

Batch to Batch Repeatability

One batch is an exposure to a Clean in Place / Steam in Place (CIP/SIP) process with maximum temperature of 400°F (204°C) for 2 hours.

±0.025 psi (0.0017 bar) for 100 batches

Vibration Effect

Less than ±0.1% of URL when tested per the requirements of IEC 60770 control room level

RFI Effects

±0.15% of span from 20 MHz to 1000 MHz for field strength up to 10 V/m.

www.rosemount.com

Image 55
Contents Reference Manual Page Rosemount 4500 Hygienic Pressure Transmitter Page Table of Contents Section Operation MaintenanceSection Introduction Using this ManualService Support Overview Safety Messages Section InstallationGeneral ConsiderationsEnvironmental Hart Installation Flowchart Mount the Transmitter Installation ProceduresLCD Switches LOI Switches Set SwitchesAMS Configure Alarm DirectionHart Terminal Blocks Connect Wiring and Power UpGrounding Installing the LCD MeterSection Configuration Commissioning on the Bench with Hart Setting the Loop to ManualWiring Diagrams Menu Tree Hart CommunicatorFunction Hart Fast Key Sequence Fast Key SequenceReview Configuration Data Check Output Sensor TemperatureProcess Variables Set Process Variable Units Basic SetupRerange Fast Keys 3, 1 LCD Display DampingFailure Mode Alarm and Saturation Detailed SetupAlarm and Saturation Level Configuration Alarm and Saturation Values for Multidrop Mode Alarm and Saturation Levels for Burst ModeAlarm Level Verification Process Alerts Scaled Variable Configuration Rosemount Re-mapping Diagnostics Service Sensor Temperature UnitTransmitter Test Loop Test Advanced Functions for Hart Protocol Saving, Recalling, Cloning Configuration DataRosemount Burst Mode Multidrop Communication Communicating with a Multidropped Transmitter Changing a Transmitter AddressPolling a Multidropped Transmitter Overview Calibration for Hart Protocol Operation and MaintenanceCalibration Overview Transmitter Data Flow with Calibration Options Determining Calibration Frequency Calculate total probable error TPEChoosing a Trim Procedure Sensor Trim Full Trim Zero TrimRecall Factory Trim Recall Factory Trim- Sensor Trim Analog Output Trim Digital-to-Analog Trim Recall Factory Trim- Analog OutputDigital-to-Analog Trim Using Other Scale Fail Module Diagnostic MessagesNonpv Limit Stuck KEY Troubleshooting Symptom Corrective Actions Performance Specifications SpecificationsAppendix a Reference Data 00809-0100-4027, Rev AA December Range and Sensor Limits Functional SpecificationsRosemount Physical Specifications 11/2 inch Tri-Clamp Module Dimensional DrawingsInch Tri-Clamp Module Fractional Line Fitting Module Code Process Connection Style Ordering InformationAppendix B Product Certificates North American Certifications Hazardous Locations CertificationsRosemount Rosemount Index Index-2 Page ¢00809-0100-4027 ¤