Invacare Top End Terminator Jr manual Adjustable Tension Straps, Back Upholstery Cover

Page 14

PROCEDURE 4

BACK

B A C K

REPLACING CUSTOM MANUAL ADJUSTABLE TENSION BACK UPHOLSTERY (FIGURE 5)

The Adjustable Tension Straps

The straps can be adjusted at various levels of tension to accommodate individual end-users. The bottom two (2) straps can be adjusted tightly to support and/or assist the extensor muscles.

The Back Upholstery Cover

The back upholstery cover is designed for three (3) reasons:

1.The first is as a modesty cover.

2.The second is to keep the cushion from sliding out of the back of the wheelchair.

3.The third is a sacral support depending upon how far or tight the flap is pulled under the seat cushion.

WARNING

After the adjustable tension back upholstery has been positioned to the end-users individual needs, the fastening straps MUST be securely fastened BEFORE applying the back upholstery cover. The adjustable back should be checked whenever entering the wheelchair to ensure that the fastening straps are securely fastened.

9.Secure the back upholstery cover (fastening strap) to the back of the adjustable back upholstery (fas- tening strap).

10.Flip the back upholstery cover over the adjustable back upholstery and secure the fastening straps to the front of the adjustable back upholstery.

11.Lay the front portion of the back upholstery cover on the seat pan.

12.Adjust the slack in the back upholstery cover and then secure to the seat pan fastening straps.

Replacing Adjustable Tension Back Upholstery

1.Remove the back height adjustment screws that se- cure the back canes to the back uprights.

2.Slide the back canes out of the back uprights.

3.Remove the two (2) screws and washers that secure the EXISTING back upholstery to the back canes.

4.Slide the EXISTING back upholstery down and off the back canes.

5.Stand behind the wheelchair and perform the following:

A.Slide anchor loop section of adjustable tension back upholstery up onto the LEFT back cane with the up- per grommet hole facing the rear of the wheelchair.

B.Slideadjusterstrapsectionofadjustabletensionback upholstery up onto the RIGHT back cane with the uppergrommetholefacingtherearofthewheelchair.

6.Align the mounting hole in each back cane with the desired mounting hole in each back upright.

NOTE: Both back canes should be adjusted to the same height.

7.Install the two (2) back height adjustment screws through the back upright mounting holes determined in STEP 6 and the back cane mounting holes.

8.Slip adjuster straps through corresponding anchor loops and adjust the back upholstery. Secure with the fastening straps.

Back Cane

Back

Upright

Back Height

Adjustment

Screw

Fastening Strap

Back Upholstery Cover

Fastening Straps

Adjuster Strap

Anchor Back

Loop Cane

Upper

Grommet

Back UpholsteryHole

Anchor Loop Section

Mounting Screw

Back Upholstery Adjuster Strap Section

FIGURE 5 - REPLACING CUSTOM MANUAL ADJUSTABLE TENSION BACK UPHOLSTERY

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Terminator Junior JR Special Notes Table of Contents Specifications General Guidelines SAFETY/HANDLING Wheelchairs ProcedureCoping with Everyday Obstacles Percentage of Weight DistributionStability and Balance Reaching, Leaning Backwards Functional Reach From a WheelchairReaching, Leaning and Bending Forward TiltingStairways Transferring to and From Other SeatsSafety Inspection Checklist Initially Inspect Adjust Weekly Monthly PeriodicallyMaintenance Safety Precautions TroubleshootingMaintenance Suggested Maintenance ProceduresFolding the Back FOLDING/UNFOLDING the Back FigureChanging the Back Angle Figure Unfolding the BackBack Back Upholstery Cover Adjustable Tension StrapsReplacing Adjustable Tension Back Upholstery Slide the back canes out of the back uprightsReplacing the Locking Mechanism in the Back Cane Figure Back in this procedure of the manualReplacing the Spreader BAR Figure CaneInstalling the Stroller Handles Figure Installing the Stroller HandlesInstalling Using Cantilever Arms FigureINSTALLING/REMOVING Cantilever Arms Figure RemovingAdjusting Cantilever ARM Height Figure Adjusting Cantilever ARM Angle Figures 2Armrest Pad Replacement Armrest PAD ADJUSTMENT/ Replacement FigureArmrest Pad Adjustment Adjusting the T-ARMS Installing T-ARM Sockets FigureINSTALLING/REMOVING T-ARMS Figure Adjusting T-Arm Sockets Figure Adjusting T-Arm Depth FigureAdjusting T-Arm Width Figure Adjusting T-ARM Sockets Replacing the T-ARM Locking Lever FigureReplacing Seat PAN Figure Adjusting Rear Seat Height FigureAdjusting Seat Depth Figures 2 PerformSTEPS1-2 ofREPLACINGTHESEATPANA T Determining Frame Height Figure Adjusting Seat Width FigureAdjusting Front SEAT-TO-FLOOR Height Front Seat-to-floor Height Adjustment Ensure wheel locks engage properly. Refer toREMOVING/INSTALLING Rear Wheels Figure Adjusting QUICK-RELEASE Axles FigureHandrim Replacement Figure Adjusting QUAD-RELEASE Handles FigureInstalling QUAD-RELEASE Axles Figure Removing Play From Rear WheelsCamber Clamps REPAIRING/REPLACING Rear WHEEL, TIRE/TUBEOPENING/CLOSING Clamps Figure Receiver Tube ClampsAdjusting Rear Wheel Camber Figure Closed PositionDetermining Toe In/Toe Out Figures 8 DETERMINING/ADJUSTING TOE IN/TOE OUTAdjusting Toe In/Toe Out Figure Adjusting Wheelbase Length Figure ING TOE IN/TOE OUT inthisprocedureofthemanualAdjusting Wheelbase Width Figure Replacing Axle Tube FigureRepositioning the Axle Tube Figures 14 E E L S Replacing Front Casters Adjusting Front Caster Height FigureREPOSITIONING/REPLACING Front Casters Figure Repositioning Front CastersRepeat Steps 2-5 on the opposite front caster Wheel Lock ADJUSTMENT/ Replacement FigureRepeat this procedure for the opposite wheel lock Engage the wheel lockReplacing Flip-Up Footboard ADJUSTING/REPLACING FLIP-UP Footboard FigureAdjusting Flip-Up Footboard Tubular Footrest Figure ADJUSTING/REPLACING RigidANTI-TIPPER REPLACEMENT/ Adjustment Figure Elastomers and Suspension Replacing Front Elastomers FigurePage Page Limited Warranty One Invacare Way Chedworth Way

Top End Terminator Jr specifications

The Invacare Top End Terminator Jr is a premier wheelchair designed specifically for young athletes, providing both performance and versatility. It caters to the needs of competitive youth athletes, ensuring superior functionality and comfort during sports activities. The Terminator Jr blends advanced technology with thoughtful design, allowing young users to experience the thrill of competitive racing.

One of the standout features of the Terminator Jr is its lightweight aluminum frame. This construction not only enhances portability but also ensures that the wheelchair is robust enough to withstand the rigors of competitive sports. The frame is designed to provide optimal rigidity and stability, which translates into improved performance during races.

The Terminator Jr boasts an adjustable camber. This feature allows users to modify the angle of the wheels for increased speed and maneuverability. By altering the camber, athletes can optimize their performance based on personal preference and training requirements, making it an adaptable choice for different racing conditions and environments.

Another significant aspect of the Terminator Jr is its high-quality wheels and tires. The wheelchair is equipped with specialized racing wheels that offer excellent traction and control on various surfaces. The tires are designed for speed while ensuring stability, contributing to a superior racing experience.

The seat and backrests of the Terminator Jr are designed with comfort and support in mind. The seating system is adjustable, allowing for customization according to the athlete’s size and needs. This level of personalization helps to prevent discomfort during long periods of use, enabling young athletes to focus entirely on their performance.

Additionally, the Terminator Jr includes a variety of accessory options, such as footrests and backrest supports, which can be tailored to the athlete's preferences. This adaptability is key in ensuring that the wheelchair meets the specific requirements of different sports and individual users.

Safety and durability are paramount in the design of the Invacare Top End Terminator Jr. Its superior construction ensures that it can handle the physical demands of competitive racing, providing athletes with peace of mind as they focus on their performance.

In summary, the Invacare Top End Terminator Jr is a cutting-edge racing wheelchair that emphasizes performance, comfort, and customization. With its lightweight aluminum frame, adjustable camber, high-quality wheels, and customizable seating, it stands out as an excellent choice for young athletes committed to excelling in their chosen sports.
Top Page Image Contents