Invacare Top End Terminator Jr Adjusting QUAD-RELEASE Handles Figure, Handrim Replacement Figure

Page 28

PROCEDURE 7

WHEELS

W

H

E

E

L

S

INSTALLING QUAD-RELEASE AXLES (FIGURE 3)

1.Remove rear wheel and the EXISTING quick-release axle from the wheelchair. Refer to REMOVING/IN- STALLING REAR WHEELS in this procedure of the manual.

2.Remove EXISTING quick-release axle from rear wheel.

3.Insert NEW quad-release axle through rear wheel hub.

4.Slidelockingcollarontoquad-releaseaxleuntilitissnug againstrearwheelandtightensecurelywithallenscrew.

5.Reinstall rear wheel and the quad-release axle onto the wheelchair. Refer to REMOVING/INSTALLING REAR WHEELS in this procedure of the manual.

6.Flip the handle of the quad-release axle down to re- lease the detent pin ensuring that the locking pins are fully released.

7.Ifdetentpindoesnotfullyrelease,proceedto ADJUST- ING QUAD-RELEASE HANDLE IN AND/OR OUTin this procedure of the manual.

8.Repeat STEPS 1-7 for the opposite rear wheel.

3.Make the following adjustments:

If the quad-release handle is not releasing the lock- ingpinscompletely,rotatethequad-release handle approximately one-quarter (1/4) turn CLOCKWISE.

If the quad-release handle hits the spokes of the rear wheel when assembled, rotate the quad-release handle approximately one-quarter (1/4) turn COUN-

TERCLOCKWISE.

4.Tighten the locking screw.

5.Reinstall the rear wheel and quad-release axle onto the wheelchair. Refer to REMOVING/INSTALLING REAR WHEELS in this procedure of the manual.

6.Flip the handle of the quad-release axle down to re- lease the detent pin ensuring that the locking pins are fully released.

7.Repeat the above procedures until the quad-release axle locks correctly.

Removing Play From Rear Wheels

NOTE: The adjusting locknut on the quick-release axles originally performed this function.

1. Withtherearwheelandquad-releaseaxlestillmounted

onto the wheelchair, make the following adjustment:

Quad

Release

Axle

Rear Wheel

Hub

Allen

Screw

Locking

Collar

Adjustable Axle

Position

Camber Bar

NOTE: End of Quad Release axle shown for reference only. It is not visible when inserted into camber bar

Tighten the length adjusting screw until there is no

in and out movement of the quad-release axle and

rear wheel.

Quad Release

Locking Pins

Handle

 

Locking

Camber Bar

Screw

 

ADJUSTING QUAD-

 

RELEASE HANDLE IN/

 

FIGURE 3 - INSTALLING QUAD-RELEASE AXLES

ADJUSTING QUAD-RELEASE HANDLES (FIGURE 4)

In and/or Out

1.Remove rear wheel and the quad-release axle from the wheelchair. Refer to REMOVING/INSTALLING REAR WHEELS in this procedure of the manual.

2.Loosen the locking screw.

AND OR OUT

 

REMOVING PLAY

Adjusting

 

Locknut (On

Length

FROM REAR

Quick-Release

Adjustment

WHEELS

Axle)

Screw

 

FIGURE 4 - ADJUSTING QUAD-RELEASE HANDLES

HANDRIM REPLACEMENT (FIGURE 5)

1.Remove the rear wheel from the wheelchair. Refer to REMOVING/INSTALLING REAR WHEELS in this procedure of the manual.

28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Terminator Junior JR Special Notes Table of Contents Specifications General Guidelines SAFETY/HANDLING Wheelchairs ProcedureStability and Balance Percentage of Weight DistributionCoping with Everyday Obstacles Functional Reach From a Wheelchair Reaching, Leaning and Bending ForwardReaching, Leaning Backwards TiltingStairways Transferring to and From Other SeatsSafety Inspection Checklist Initially Inspect Adjust Weekly Monthly PeriodicallyTroubleshooting MaintenanceMaintenance Safety Precautions Suggested Maintenance ProceduresFOLDING/UNFOLDING the Back Figure Changing the Back Angle FigureFolding the Back Unfolding the BackBack Adjustable Tension Straps Replacing Adjustable Tension Back UpholsteryBack Upholstery Cover Slide the back canes out of the back uprightsBack in this procedure of the manual Replacing the Spreader BAR FigureReplacing the Locking Mechanism in the Back Cane Figure CaneInstalling the Stroller Handles Figure Installing the Stroller HandlesUsing Cantilever Arms Figure INSTALLING/REMOVING Cantilever Arms FigureInstalling RemovingAdjusting Cantilever ARM Height Figure Adjusting Cantilever ARM Angle Figures 2Armrest Pad Adjustment Armrest PAD ADJUSTMENT/ Replacement FigureArmrest Pad Replacement INSTALLING/REMOVING T-ARMS Figure Installing T-ARM Sockets FigureAdjusting the T-ARMS Adjusting T-Arm Width Figure Adjusting T-Arm Depth FigureAdjusting T-Arm Sockets Figure Adjusting T-ARM Sockets Replacing the T-ARM Locking Lever FigureAdjusting Rear Seat Height Figure Adjusting Seat Depth Figures 2Replacing Seat PAN Figure PerformSTEPS1-2 ofREPLACINGTHESEATPANA T Adjusting Front SEAT-TO-FLOOR Height Adjusting Seat Width FigureDetermining Frame Height Figure Front Seat-to-floor Height Adjustment Ensure wheel locks engage properly. Refer toREMOVING/INSTALLING Rear Wheels Figure Adjusting QUICK-RELEASE Axles FigureAdjusting QUAD-RELEASE Handles Figure Installing QUAD-RELEASE Axles FigureHandrim Replacement Figure Removing Play From Rear WheelsREPAIRING/REPLACING Rear WHEEL, TIRE/TUBE OPENING/CLOSING Clamps FigureCamber Clamps Receiver Tube ClampsAdjusting Rear Wheel Camber Figure Closed PositionAdjusting Toe In/Toe Out Figure DETERMINING/ADJUSTING TOE IN/TOE OUTDetermining Toe In/Toe Out Figures 8 Adjusting Wheelbase Length Figure ING TOE IN/TOE OUT inthisprocedureofthemanualAdjusting Wheelbase Width Figure Replacing Axle Tube FigureRepositioning the Axle Tube Figures 14 E E L S Adjusting Front Caster Height Figure REPOSITIONING/REPLACING Front Casters FigureReplacing Front Casters Repositioning Front CastersWheel Lock ADJUSTMENT/ Replacement Figure Repeat this procedure for the opposite wheel lockRepeat Steps 2-5 on the opposite front caster Engage the wheel lockAdjusting Flip-Up Footboard ADJUSTING/REPLACING FLIP-UP Footboard FigureReplacing Flip-Up Footboard ANTI-TIPPER REPLACEMENT/ Adjustment Figure ADJUSTING/REPLACING RigidTubular Footrest Figure Elastomers and Suspension Replacing Front Elastomers FigurePage Page Limited Warranty One Invacare Way Chedworth Way

Top End Terminator Jr specifications

The Invacare Top End Terminator Jr is a premier wheelchair designed specifically for young athletes, providing both performance and versatility. It caters to the needs of competitive youth athletes, ensuring superior functionality and comfort during sports activities. The Terminator Jr blends advanced technology with thoughtful design, allowing young users to experience the thrill of competitive racing.

One of the standout features of the Terminator Jr is its lightweight aluminum frame. This construction not only enhances portability but also ensures that the wheelchair is robust enough to withstand the rigors of competitive sports. The frame is designed to provide optimal rigidity and stability, which translates into improved performance during races.

The Terminator Jr boasts an adjustable camber. This feature allows users to modify the angle of the wheels for increased speed and maneuverability. By altering the camber, athletes can optimize their performance based on personal preference and training requirements, making it an adaptable choice for different racing conditions and environments.

Another significant aspect of the Terminator Jr is its high-quality wheels and tires. The wheelchair is equipped with specialized racing wheels that offer excellent traction and control on various surfaces. The tires are designed for speed while ensuring stability, contributing to a superior racing experience.

The seat and backrests of the Terminator Jr are designed with comfort and support in mind. The seating system is adjustable, allowing for customization according to the athlete’s size and needs. This level of personalization helps to prevent discomfort during long periods of use, enabling young athletes to focus entirely on their performance.

Additionally, the Terminator Jr includes a variety of accessory options, such as footrests and backrest supports, which can be tailored to the athlete's preferences. This adaptability is key in ensuring that the wheelchair meets the specific requirements of different sports and individual users.

Safety and durability are paramount in the design of the Invacare Top End Terminator Jr. Its superior construction ensures that it can handle the physical demands of competitive racing, providing athletes with peace of mind as they focus on their performance.

In summary, the Invacare Top End Terminator Jr is a cutting-edge racing wheelchair that emphasizes performance, comfort, and customization. With its lightweight aluminum frame, adjustable camber, high-quality wheels, and customizable seating, it stands out as an excellent choice for young athletes committed to excelling in their chosen sports.
Top Page Image Contents