Invacare Top End Terminator Jr manual Using Cantilever Arms Figure, Installing, Removing

Page 17

ARMS

PROCEDURE 5

This Procedure includes the following:

Using Cantilever Arms

Installing/Removing Cantilever Arms

Adjusting Cantilever Arm Height

Adjusting Cantilever Arm Angle

Replacing/Repositioning the Cantilever Arm Locking Mechanism

Arm Pad Adjustment/Replacement

Installing T-Arm Sockets

Installing/Removing T-Arms

Adjusting the T-Arms

Replacing the T-Arm Locking Lever

WARNING

Never try to lift or tip the wheelchair by the cantilever arms or T-arms, serious injury can occur.

After ANY adjustments, repair or service and BEFORE use, make sure all attachment hard- ware is tightened securely - otherwise, injury or damage may occur.

USING CANTILEVER ARMS (FIGURE 1)

1.Pull the locking mechanism actuator towards the front of the wheelchair.

2.While holding the actuator, pull UP on the cantile- ver arm.

Adjustment Plate

 

Back Cane

 

 

REAR

Coved

Locknuts

Washers

Actuator Spacer

Washers

FRONT

Top Hex Screw

and Coved Washer

Bottom Hex Screw

Cantilever Arm

 

FIGURE 1 - USING CANTILEVER ARMS - INSTALLING/

REMOVING CANTILEVER ARMS - ADJUSTING

CANTILEVER ARM HEIGHT

INSTALLING/REMOVING CANTILEVER ARMS (FIGURE 1)

Installing

1.Insert the top hex screw of the partially assembled cantilever arm assembly through the desired back cane mounting hole.

NOTE: The partially assembled cantilever arm assem- bly includes the top hex screw, coved washers and spacer, adjustment plate and cantilever arm.

NOTE: Make sure the adjustment plate is towards the inside of the wheelchair.

A R M S

NOTE: If cantilever arms rub against rear wheels when UP, increase the wheelbase width. Refer to ADJUST- ING WHEELBASE WIDTH in PROCEDURE 7 of this manual.

NOTE: If necessary, the locking mechanism in the can- tilever arm can be repositioned so the cantilever arm will flip DOWN instead of UP. Refer to REPLACING/ REPOSITIONING THE CANTILEVER ARM LOCK- ING MECHANISM in this procedure of the manual.

3.To lock the cantilever arm, push DOWN until there is an audible click.

4.Pull UP on the cantilever arm to make sure it is locked in place.

2.Insert the bottom hex screw through the bottom hole of the adjustment plate, the coved washer and the back cane.

3.Secure the cantilever arm to the wheelchair with the washers and locknuts as shown in FIGURE 1.

4.If desired, adjust the angle of the cantilever arm. Refer to ADJUSTING CANTILEVER ARM ANGLE in this procedure of the manual.

Removing

NOTE: When removing the locknuts and washers from the cantilever arm assembly, leave the hex screws, coved washers and spacer in place.

1.Remove the locknuts and washers from the top and bottom hex screws.

2.Remove the cantilever arm assembly from the wheelchair frame.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Terminator Junior JR Special Notes Table of Contents Specifications General Guidelines Procedure SAFETY/HANDLING WheelchairsCoping with Everyday Obstacles Percentage of Weight DistributionStability and Balance Reaching, Leaning and Bending Forward Functional Reach From a WheelchairReaching, Leaning Backwards TiltingTransferring to and From Other Seats StairwaysInitially Inspect Adjust Weekly Monthly Periodically Safety Inspection ChecklistMaintenance TroubleshootingMaintenance Safety Precautions Suggested Maintenance ProceduresChanging the Back Angle Figure FOLDING/UNFOLDING the Back FigureFolding the Back Unfolding the BackBack Replacing Adjustable Tension Back Upholstery Adjustable Tension StrapsBack Upholstery Cover Slide the back canes out of the back uprightsReplacing the Spreader BAR Figure Back in this procedure of the manualReplacing the Locking Mechanism in the Back Cane Figure CaneInstalling the Stroller Handles Installing the Stroller Handles FigureINSTALLING/REMOVING Cantilever Arms Figure Using Cantilever Arms FigureInstalling RemovingAdjusting Cantilever ARM Angle Figures 2 Adjusting Cantilever ARM Height FigureArmrest Pad Replacement Armrest PAD ADJUSTMENT/ Replacement FigureArmrest Pad Adjustment Adjusting the T-ARMS Installing T-ARM Sockets FigureINSTALLING/REMOVING T-ARMS Figure Adjusting T-Arm Sockets Figure Adjusting T-Arm Depth FigureAdjusting T-Arm Width Figure Replacing the T-ARM Locking Lever Figure Adjusting T-ARM SocketsAdjusting Seat Depth Figures 2 Adjusting Rear Seat Height FigureReplacing Seat PAN Figure PerformSTEPS1-2 ofREPLACINGTHESEATPANA T Determining Frame Height Figure Adjusting Seat Width FigureAdjusting Front SEAT-TO-FLOOR Height Ensure wheel locks engage properly. Refer to Front Seat-to-floor Height AdjustmentAdjusting QUICK-RELEASE Axles Figure REMOVING/INSTALLING Rear Wheels FigureInstalling QUAD-RELEASE Axles Figure Adjusting QUAD-RELEASE Handles FigureHandrim Replacement Figure Removing Play From Rear WheelsOPENING/CLOSING Clamps Figure REPAIRING/REPLACING Rear WHEEL, TIRE/TUBECamber Clamps Receiver Tube ClampsClosed Position Adjusting Rear Wheel Camber FigureDetermining Toe In/Toe Out Figures 8 DETERMINING/ADJUSTING TOE IN/TOE OUTAdjusting Toe In/Toe Out Figure ING TOE IN/TOE OUT inthisprocedureofthemanual Adjusting Wheelbase Length FigureReplacing Axle Tube Figure Adjusting Wheelbase Width FigureRepositioning the Axle Tube Figures 14 E E L S REPOSITIONING/REPLACING Front Casters Figure Adjusting Front Caster Height FigureReplacing Front Casters Repositioning Front CastersRepeat this procedure for the opposite wheel lock Wheel Lock ADJUSTMENT/ Replacement FigureRepeat Steps 2-5 on the opposite front caster Engage the wheel lockReplacing Flip-Up Footboard ADJUSTING/REPLACING FLIP-UP Footboard FigureAdjusting Flip-Up Footboard Tubular Footrest Figure ADJUSTING/REPLACING RigidANTI-TIPPER REPLACEMENT/ Adjustment Figure Replacing Front Elastomers Figure Elastomers and SuspensionPage Page Limited Warranty One Invacare Way Chedworth Way

Top End Terminator Jr specifications

The Invacare Top End Terminator Jr is a premier wheelchair designed specifically for young athletes, providing both performance and versatility. It caters to the needs of competitive youth athletes, ensuring superior functionality and comfort during sports activities. The Terminator Jr blends advanced technology with thoughtful design, allowing young users to experience the thrill of competitive racing.

One of the standout features of the Terminator Jr is its lightweight aluminum frame. This construction not only enhances portability but also ensures that the wheelchair is robust enough to withstand the rigors of competitive sports. The frame is designed to provide optimal rigidity and stability, which translates into improved performance during races.

The Terminator Jr boasts an adjustable camber. This feature allows users to modify the angle of the wheels for increased speed and maneuverability. By altering the camber, athletes can optimize their performance based on personal preference and training requirements, making it an adaptable choice for different racing conditions and environments.

Another significant aspect of the Terminator Jr is its high-quality wheels and tires. The wheelchair is equipped with specialized racing wheels that offer excellent traction and control on various surfaces. The tires are designed for speed while ensuring stability, contributing to a superior racing experience.

The seat and backrests of the Terminator Jr are designed with comfort and support in mind. The seating system is adjustable, allowing for customization according to the athlete’s size and needs. This level of personalization helps to prevent discomfort during long periods of use, enabling young athletes to focus entirely on their performance.

Additionally, the Terminator Jr includes a variety of accessory options, such as footrests and backrest supports, which can be tailored to the athlete's preferences. This adaptability is key in ensuring that the wheelchair meets the specific requirements of different sports and individual users.

Safety and durability are paramount in the design of the Invacare Top End Terminator Jr. Its superior construction ensures that it can handle the physical demands of competitive racing, providing athletes with peace of mind as they focus on their performance.

In summary, the Invacare Top End Terminator Jr is a cutting-edge racing wheelchair that emphasizes performance, comfort, and customization. With its lightweight aluminum frame, adjustable camber, high-quality wheels, and customizable seating, it stands out as an excellent choice for young athletes committed to excelling in their chosen sports.
Top Page Image Contents