Invacare Top End Terminator Jr manual Repositioning the Axle Tube Figures 14

Page 34
FIGURE 14 - REPOSITIONING THE AXLE TUBE
Telescoping Tube Mounting Plate
INSIDE OF
WHEELCHAIR
Telescoping
Tube
Locknuts
Camber Clamp Mounting Plate
Long Hex
Screw
Short Hex
Screw
Camber Clamp
OUTSIDE OF
WHEELCHAIR
17. Adjust anti-tippers. Refer to ANTI-TIPPER ADJUST- MENT/REPLACEMENT in PROCEDURE 8 of the manual.
Anti-tip
Tube
WHEELS
4. Remove the locknuts and hex bolts securing the telescoping tube mounting plate to the camber clamps mounting plate.
5. Perform one (1) of the following:
A. CLAMPPOSITIONMUSTBEREVERSED-Pro- ceed to STEP 6.
B. CLAMP POSITION REMAINS IN STANDARD POSITION - proceed to STEP 11.
6. Loosen the hex screw securing the telescoping tube clamp.
7. RemovetheRIGHTtelescopingtubewheelchairframe and set aside.
8. Remove the LEFT telescoping tube from the wheel- chair frame.
9. Insert the LEFT telescoping tube into the RIGHT side of the wheelchair frame with the mounting plate to- wards the INSIDE of the wheelchair.
10. Repeat STEP 9 for the RIGHT telesocping tube and the LEFT side of the wheelchair frame.
11. Align the camber clamp mounting plate holes with the telescoping tube mounting plate holes determined in STEP 5.
12. Install the long hex screw through the telescoping tube and the camber clamp mounting plate.
13. Installtheshorthexscrewthroughthetelescopingtube mounting plate and the camber clamp mounting plate.
14. Secure both hex screws with the two (2) locknuts.
15. Installtherearwheels.Referto REMOVING/INSTALL- ING REAR WHEELS in this procedure of the manual.
16. Ensure the caster headtubes are perpendicular to the ground. Adjust caster height if necessary. Refer to AD- JUSTING FRONT CASTER HEIGHT in this proce- dure of the manual.

W

H

E

E

L

S

PROCEDURE 7

10.SlidetheNEWaxletubethroughtheothercamberclamp untiltheendoftheaxletubeisflushwiththeoutsideofthe camber clamp.

NOTE: DO NOT close the quick release levers or tighten the hexscrewsthatsecuretheaxletubetothecamberclampsat this time.

WARNING

NEVER position the camber inserts in the axle tube with more than 3-inches (12 indexing marks show- ing) of the camber insert outside of the axle tube. The camber inserts will not be securely tightened in theaxletuberesultinginpossibleinjury totheuseror damage to the wheelchair.

11.Install the rear wheels and camber inserts into the NEW axle tube and slide the camber inserts to the position noted in STEP 1. Make sure there is no more than 3- inches(12indexingmarks)ofthecamberinsertsoutside of the axle tube.

12.Slide the indexing ring on the camber insert until it is flush with the camber clamp

NOTE: To maximize rollability: Before using the wheelchair, make sure both camber inserts are set to the same indexing notch.Thiswillmakesurethedistancebetweentherearwheel and the wheelchair is the same on both sides.

13.Adjust the toe-in/toe-out of the wheelchair. Refer to DE- TERMINING/ADJUSTING TOE-IN/TOE-OUTin this procedure of the manual.

NOTE: The performance of the wheelchair will be affected if the axle tube has not been adjusted to correct the toe in/toe out of the wheelchair.

14.Ensure the camber clamps are closed. Refer to OPEN- ING/CLOSINGCLAMPSinthisprocedureofthemanual.

REPOSITIONING THE AXLE TUBE (FIGURES 14 AND 15)

NOTE: This procedure should only be performed if changing the front seat-to-floor height. Refer to ADJUSTING FRONT SEAT-TO-FLOORHEIGHTinPROCEDURE6ofthismanual.

NOTE: Right and left are determined by standing behind the wheelchair.

1.Remove the rear wheels from the wheelchair. Refer to REMOVING/INSTALLING REAR WHEELS in this pro- cedure of the manual.

2.Positionthewheelchaironaflatsurfacewiththeunderside facing UP.

2.Refer to ADJUSTING FRONT SEAT-TO-FLOOR HEIGHT in PROCEDURE 6 of the manual to determine the proper position for the axle tube.

3.Refer to the chart in FIGURE 15 to determine the proper axle tube adjustment.

NOTE:RefertoDETAIL"B"ofFIGURE15fortelescopingtube and camber clamp mounting hole patterns.

34

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Terminator Junior JR Special Notes Table of Contents Specifications General Guidelines SAFETY/HANDLING Wheelchairs ProcedureStability and Balance Percentage of Weight DistributionCoping with Everyday Obstacles Reaching, Leaning Backwards Functional Reach From a WheelchairReaching, Leaning and Bending Forward TiltingStairways Transferring to and From Other SeatsSafety Inspection Checklist Initially Inspect Adjust Weekly Monthly PeriodicallyMaintenance Safety Precautions TroubleshootingMaintenance Suggested Maintenance ProceduresFolding the Back FOLDING/UNFOLDING the Back FigureChanging the Back Angle Figure Unfolding the BackBack Back Upholstery Cover Adjustable Tension StrapsReplacing Adjustable Tension Back Upholstery Slide the back canes out of the back uprightsReplacing the Locking Mechanism in the Back Cane Figure Back in this procedure of the manualReplacing the Spreader BAR Figure CaneInstalling the Stroller Handles Figure Installing the Stroller HandlesInstalling Using Cantilever Arms FigureINSTALLING/REMOVING Cantilever Arms Figure RemovingAdjusting Cantilever ARM Height Figure Adjusting Cantilever ARM Angle Figures 2Armrest Pad Adjustment Armrest PAD ADJUSTMENT/ Replacement FigureArmrest Pad Replacement INSTALLING/REMOVING T-ARMS Figure Installing T-ARM Sockets FigureAdjusting the T-ARMS Adjusting T-Arm Width Figure Adjusting T-Arm Depth FigureAdjusting T-Arm Sockets Figure Adjusting T-ARM Sockets Replacing the T-ARM Locking Lever FigureReplacing Seat PAN Figure Adjusting Rear Seat Height FigureAdjusting Seat Depth Figures 2 PerformSTEPS1-2 ofREPLACINGTHESEATPANA T Adjusting Front SEAT-TO-FLOOR Height Adjusting Seat Width FigureDetermining Frame Height Figure Front Seat-to-floor Height Adjustment Ensure wheel locks engage properly. Refer toREMOVING/INSTALLING Rear Wheels Figure Adjusting QUICK-RELEASE Axles FigureHandrim Replacement Figure Adjusting QUAD-RELEASE Handles FigureInstalling QUAD-RELEASE Axles Figure Removing Play From Rear WheelsCamber Clamps REPAIRING/REPLACING Rear WHEEL, TIRE/TUBEOPENING/CLOSING Clamps Figure Receiver Tube ClampsAdjusting Rear Wheel Camber Figure Closed PositionAdjusting Toe In/Toe Out Figure DETERMINING/ADJUSTING TOE IN/TOE OUTDetermining Toe In/Toe Out Figures 8 Adjusting Wheelbase Length Figure ING TOE IN/TOE OUT inthisprocedureofthemanualAdjusting Wheelbase Width Figure Replacing Axle Tube FigureRepositioning the Axle Tube Figures 14 E E L S Replacing Front Casters Adjusting Front Caster Height FigureREPOSITIONING/REPLACING Front Casters Figure Repositioning Front CastersRepeat Steps 2-5 on the opposite front caster Wheel Lock ADJUSTMENT/ Replacement FigureRepeat this procedure for the opposite wheel lock Engage the wheel lockAdjusting Flip-Up Footboard ADJUSTING/REPLACING FLIP-UP Footboard FigureReplacing Flip-Up Footboard ANTI-TIPPER REPLACEMENT/ Adjustment Figure ADJUSTING/REPLACING RigidTubular Footrest Figure Elastomers and Suspension Replacing Front Elastomers FigurePage Page Limited Warranty One Invacare Way Chedworth Way

Top End Terminator Jr specifications

The Invacare Top End Terminator Jr is a premier wheelchair designed specifically for young athletes, providing both performance and versatility. It caters to the needs of competitive youth athletes, ensuring superior functionality and comfort during sports activities. The Terminator Jr blends advanced technology with thoughtful design, allowing young users to experience the thrill of competitive racing.

One of the standout features of the Terminator Jr is its lightweight aluminum frame. This construction not only enhances portability but also ensures that the wheelchair is robust enough to withstand the rigors of competitive sports. The frame is designed to provide optimal rigidity and stability, which translates into improved performance during races.

The Terminator Jr boasts an adjustable camber. This feature allows users to modify the angle of the wheels for increased speed and maneuverability. By altering the camber, athletes can optimize their performance based on personal preference and training requirements, making it an adaptable choice for different racing conditions and environments.

Another significant aspect of the Terminator Jr is its high-quality wheels and tires. The wheelchair is equipped with specialized racing wheels that offer excellent traction and control on various surfaces. The tires are designed for speed while ensuring stability, contributing to a superior racing experience.

The seat and backrests of the Terminator Jr are designed with comfort and support in mind. The seating system is adjustable, allowing for customization according to the athlete’s size and needs. This level of personalization helps to prevent discomfort during long periods of use, enabling young athletes to focus entirely on their performance.

Additionally, the Terminator Jr includes a variety of accessory options, such as footrests and backrest supports, which can be tailored to the athlete's preferences. This adaptability is key in ensuring that the wheelchair meets the specific requirements of different sports and individual users.

Safety and durability are paramount in the design of the Invacare Top End Terminator Jr. Its superior construction ensures that it can handle the physical demands of competitive racing, providing athletes with peace of mind as they focus on their performance.

In summary, the Invacare Top End Terminator Jr is a cutting-edge racing wheelchair that emphasizes performance, comfort, and customization. With its lightweight aluminum frame, adjustable camber, high-quality wheels, and customizable seating, it stands out as an excellent choice for young athletes committed to excelling in their chosen sports.
Top Page Image Contents