Invacare Top End Terminator Jr Armrest PAD ADJUSTMENT/ Replacement Figure, Armrest Pad Adjustment

Page 19

ARMS

PROCEDURE 5

REPLACING/REPOSITIONING THE CANTILEVER ARM LOCKING MECHANISM (FIGURE 4)

CAUTION

The locking mechanism is spring loaded. Place your free hand over the end of the cantilever arm to prevent the locking mechanism from springing out of the arm.

1.Flip the cantilever arm up and out of the way.

2.Unscrew the actuator from the locking mechanism.

3.Remove the locking mechanism and spring from the cantilever arm.

NOTE: Inspect the spring and replace if necessary.

4.Slide the NEW spring and locking mechanism into the cantilever arm.

5.Position the angled portion of the locking mecha- nism in one (1) of two (2) ways:

A.ANGLED PORTION FACING UP - Arm will flip UP.

B.ANGLED PORTION FACING DOWN - Arm will flip DOWN.

6.Push and hold the locking mechanism into the cantilever arm.

7.Screw the actuator into the locking mechanism mounting hole.

8.Flip the cantilever arm up/down to lock in place.

9.Pull down/up on the cantilever arm to ensure it has locked in place.

Angled Portion of

Locking Mechanism

Spring

Cantilever Arm

Locking

Mechanism

Actuator

FIGURE 4 - REPOSITIONING/REPLACING THE

LOCKING MECHANISM IN THE

CANTILEVER ARM

ARMREST PAD ADJUSTMENT/ REPLACEMENT (FIGURE 5)

Armrest Pad Adjustment

1.Remove the phillips screw from the rear of the armrest pad.

2.Reposition the cantilever slide tube to one (1) of five (5) positions.

3.Align the mounting hole in the cantilever slide tube with the desired mounting hole from STEP 2.

4.Install the phillips screw UP through the desired mounting hole in the armrest tube and the cantile- ver slide tube mounting hole to secure the arm- rest pad to the armrest tube.

5.Repeat STEPS 1-4 for opposite armrest pad if necessary.

Armrest Pad Replacement

1.Remove the phillips screw from the rear of the armrest pad.

2.Remove the phillips screw from the front of the armrest pad.

3.Remove the EXISTING armrest pad from the arm- rest tube.

4.Position the NEW armrest pad onto the armrest tube and cantilever slide tube.

5.Secure the NEW armrest pad to the armrest tube and cantilever slide tube with the two (2) phillips screws.

Armrest

Tube

REAR Phillips Screw

Cantilever Slide Tube

FRONT Phillips Screw

FIGURE 5 - ARMREST PAD ADJUSTMENT/

REPLACEMENT

A R M S

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Terminator Junior JR Special Notes Table of Contents Specifications General Guidelines Procedure SAFETY/HANDLING WheelchairsStability and Balance Percentage of Weight DistributionCoping with Everyday Obstacles Tilting Functional Reach From a WheelchairReaching, Leaning and Bending Forward Reaching, Leaning BackwardsTransferring to and From Other Seats StairwaysInitially Inspect Adjust Weekly Monthly Periodically Safety Inspection ChecklistSuggested Maintenance Procedures TroubleshootingMaintenance Maintenance Safety PrecautionsUnfolding the Back FOLDING/UNFOLDING the Back FigureChanging the Back Angle Figure Folding the BackBack Slide the back canes out of the back uprights Adjustable Tension StrapsReplacing Adjustable Tension Back Upholstery Back Upholstery CoverCane Back in this procedure of the manualReplacing the Spreader BAR Figure Replacing the Locking Mechanism in the Back Cane FigureInstalling the Stroller Handles Installing the Stroller Handles FigureRemoving Using Cantilever Arms FigureINSTALLING/REMOVING Cantilever Arms Figure InstallingAdjusting Cantilever ARM Angle Figures 2 Adjusting Cantilever ARM Height FigureArmrest Pad Adjustment Armrest PAD ADJUSTMENT/ Replacement FigureArmrest Pad Replacement INSTALLING/REMOVING T-ARMS Figure Installing T-ARM Sockets FigureAdjusting the T-ARMS Adjusting T-Arm Width Figure Adjusting T-Arm Depth FigureAdjusting T-Arm Sockets Figure Replacing the T-ARM Locking Lever Figure Adjusting T-ARM SocketsPerformSTEPS1-2 ofREPLACINGTHESEATPAN Adjusting Rear Seat Height FigureAdjusting Seat Depth Figures 2 Replacing Seat PAN FigureA T Adjusting Front SEAT-TO-FLOOR Height Adjusting Seat Width FigureDetermining Frame Height Figure Ensure wheel locks engage properly. Refer to Front Seat-to-floor Height AdjustmentAdjusting QUICK-RELEASE Axles Figure REMOVING/INSTALLING Rear Wheels FigureRemoving Play From Rear Wheels Adjusting QUAD-RELEASE Handles FigureInstalling QUAD-RELEASE Axles Figure Handrim Replacement FigureReceiver Tube Clamps REPAIRING/REPLACING Rear WHEEL, TIRE/TUBEOPENING/CLOSING Clamps Figure Camber ClampsClosed Position Adjusting Rear Wheel Camber FigureAdjusting Toe In/Toe Out Figure DETERMINING/ADJUSTING TOE IN/TOE OUTDetermining Toe In/Toe Out Figures 8 ING TOE IN/TOE OUT inthisprocedureofthemanual Adjusting Wheelbase Length FigureReplacing Axle Tube Figure Adjusting Wheelbase Width FigureRepositioning the Axle Tube Figures 14 E E L S Repositioning Front Casters Adjusting Front Caster Height FigureREPOSITIONING/REPLACING Front Casters Figure Replacing Front CastersEngage the wheel lock Wheel Lock ADJUSTMENT/ Replacement FigureRepeat this procedure for the opposite wheel lock Repeat Steps 2-5 on the opposite front casterAdjusting Flip-Up Footboard ADJUSTING/REPLACING FLIP-UP Footboard FigureReplacing Flip-Up Footboard ANTI-TIPPER REPLACEMENT/ Adjustment Figure ADJUSTING/REPLACING RigidTubular Footrest Figure Replacing Front Elastomers Figure Elastomers and SuspensionPage Page Limited Warranty One Invacare Way Chedworth Way

Top End Terminator Jr specifications

The Invacare Top End Terminator Jr is a premier wheelchair designed specifically for young athletes, providing both performance and versatility. It caters to the needs of competitive youth athletes, ensuring superior functionality and comfort during sports activities. The Terminator Jr blends advanced technology with thoughtful design, allowing young users to experience the thrill of competitive racing.

One of the standout features of the Terminator Jr is its lightweight aluminum frame. This construction not only enhances portability but also ensures that the wheelchair is robust enough to withstand the rigors of competitive sports. The frame is designed to provide optimal rigidity and stability, which translates into improved performance during races.

The Terminator Jr boasts an adjustable camber. This feature allows users to modify the angle of the wheels for increased speed and maneuverability. By altering the camber, athletes can optimize their performance based on personal preference and training requirements, making it an adaptable choice for different racing conditions and environments.

Another significant aspect of the Terminator Jr is its high-quality wheels and tires. The wheelchair is equipped with specialized racing wheels that offer excellent traction and control on various surfaces. The tires are designed for speed while ensuring stability, contributing to a superior racing experience.

The seat and backrests of the Terminator Jr are designed with comfort and support in mind. The seating system is adjustable, allowing for customization according to the athlete’s size and needs. This level of personalization helps to prevent discomfort during long periods of use, enabling young athletes to focus entirely on their performance.

Additionally, the Terminator Jr includes a variety of accessory options, such as footrests and backrest supports, which can be tailored to the athlete's preferences. This adaptability is key in ensuring that the wheelchair meets the specific requirements of different sports and individual users.

Safety and durability are paramount in the design of the Invacare Top End Terminator Jr. Its superior construction ensures that it can handle the physical demands of competitive racing, providing athletes with peace of mind as they focus on their performance.

In summary, the Invacare Top End Terminator Jr is a cutting-edge racing wheelchair that emphasizes performance, comfort, and customization. With its lightweight aluminum frame, adjustable camber, high-quality wheels, and customizable seating, it stands out as an excellent choice for young athletes committed to excelling in their chosen sports.
Top Page Image Contents