Invacare Top End Terminator Jr manual Adjusting Wheelbase Width Figure, Replacing Axle Tube Figure

Page 33

WHEELS

PROCEDURE 7

ADJUSTING WHEELBASE WIDTH (FIGURE 12)

NOTE: Perform this procedure one (1) side of the wheel- chair at a time for ease of adjustment.

1.Open the camber clamps. Refer to OPENING/CLOS- ING CLAMPS in this procedure of the manual.

WARNING

NEVERpositionthecamberinsertsintheaxletube with morethan3-inches(12indexingmarksshow- ing) of the camber insert outside of the axle tube. The camber inserts will not be securely tightened in the axle tube resulting in possible injury to the user or damage to the wheelchair.

2.Position camber insert to the desired position. Make surethereisnomorethan3-inches(12indexingmarks showing)ofthecamberinsertsoutsideoftheaxletube.

3.Slide the indexing ring on the camber insert until it is flush with the camber clamp.

NOTE: Before using the wheelchair, make sure both cam- ber inserts are set at the same indexing mark. This will make sure the distance between the rear wheel and the wheelchair is the same on both sides.

WARNING

QUICK RELEASE LEVERS - Make sure the quick re- lease levers are pointing towards the rear of the wheelchair and are in the CLOSED position BE- FORE using the wheelchair, otherwise personal injury or damage to the wheelchair may result.

STANDARD - Make sure the hex screws and lock- nuts are securely tightened BEFORE using the wheelchair, otherwise personal injury or damage to the wheelchair may result.

4.Close the camber clamps. Refer toOPENING/CLOS- ING CLAMPS in this procedure of the manual.

5.Repeat STEPS 1-4 for opposite side of wheelchair. Indexing Marks

Indexing Ring

Axle

 

Tube

Camber Insert

Camber Clamp

FIGURE 12 - ADJUSTING WHEELBASE WIDTH

REPLACING AXLE TUBE (FIGURE 13)

NOTE: There is no need to remove the two (2) camber clamps when replacing the axle tube.

1.Note the position of the camber inserts so they can be installed to the original position in the NEW axle tube.

2.Open the camber clamps. Refer to OPENING/CLOS- ING CLAMPS in this procedure of the manual.

3.Remove the two (2) rear wheels and camber inserts positioned in the axle tube.

5.Pull the EXISTING axle tube through one (1) of the camber clamps.

7.Pull the EXISTING axle tube through the other cam- ber clamp and remove from the wheelchair.

8.Slide the NEW axle tube through one (1) of the cam- ber clamps. Make sure the notches in the axle tube are towards the rear of the wheelchair and the slots in the axle tube are facing up.

W

H

E

E

L

S

 

REAR OF

Slot in

 

Axle Tube

 

WHEELCHAIR

 

 

Notch in

 

Camber Insert

Axle Tube

 

Camber Clamp

Camber Insert

Indexing Ring

Axle Tube

FRONT OF WHEELCHAIR

FIGURE 13 - REPLACING AXLE TUBE

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Terminator Junior JR Special Notes Table of Contents Specifications General Guidelines Procedure SAFETY/HANDLING WheelchairsPercentage of Weight Distribution Stability and BalanceCoping with Everyday Obstacles Reaching, Leaning and Bending Forward Functional Reach From a WheelchairReaching, Leaning Backwards TiltingTransferring to and From Other Seats StairwaysInitially Inspect Adjust Weekly Monthly Periodically Safety Inspection ChecklistMaintenance TroubleshootingMaintenance Safety Precautions Suggested Maintenance ProceduresChanging the Back Angle Figure FOLDING/UNFOLDING the Back FigureFolding the Back Unfolding the BackBack Replacing Adjustable Tension Back Upholstery Adjustable Tension StrapsBack Upholstery Cover Slide the back canes out of the back uprightsReplacing the Spreader BAR Figure Back in this procedure of the manualReplacing the Locking Mechanism in the Back Cane Figure CaneInstalling the Stroller Handles Installing the Stroller Handles FigureINSTALLING/REMOVING Cantilever Arms Figure Using Cantilever Arms FigureInstalling RemovingAdjusting Cantilever ARM Angle Figures 2 Adjusting Cantilever ARM Height FigureArmrest PAD ADJUSTMENT/ Replacement Figure Armrest Pad AdjustmentArmrest Pad Replacement Installing T-ARM Sockets Figure INSTALLING/REMOVING T-ARMS FigureAdjusting the T-ARMS Adjusting T-Arm Depth Figure Adjusting T-Arm Width FigureAdjusting T-Arm Sockets Figure Replacing the T-ARM Locking Lever Figure Adjusting T-ARM SocketsAdjusting Seat Depth Figures 2 Adjusting Rear Seat Height FigureReplacing Seat PAN Figure PerformSTEPS1-2 ofREPLACINGTHESEATPANA T Adjusting Seat Width Figure Adjusting Front SEAT-TO-FLOOR HeightDetermining Frame Height Figure Ensure wheel locks engage properly. Refer to Front Seat-to-floor Height AdjustmentAdjusting QUICK-RELEASE Axles Figure REMOVING/INSTALLING Rear Wheels FigureInstalling QUAD-RELEASE Axles Figure Adjusting QUAD-RELEASE Handles FigureHandrim Replacement Figure Removing Play From Rear WheelsOPENING/CLOSING Clamps Figure REPAIRING/REPLACING Rear WHEEL, TIRE/TUBECamber Clamps Receiver Tube ClampsClosed Position Adjusting Rear Wheel Camber FigureDETERMINING/ADJUSTING TOE IN/TOE OUT Adjusting Toe In/Toe Out FigureDetermining Toe In/Toe Out Figures 8 ING TOE IN/TOE OUT inthisprocedureofthemanual Adjusting Wheelbase Length FigureReplacing Axle Tube Figure Adjusting Wheelbase Width FigureRepositioning the Axle Tube Figures 14 E E L S REPOSITIONING/REPLACING Front Casters Figure Adjusting Front Caster Height FigureReplacing Front Casters Repositioning Front CastersRepeat this procedure for the opposite wheel lock Wheel Lock ADJUSTMENT/ Replacement FigureRepeat Steps 2-5 on the opposite front caster Engage the wheel lockADJUSTING/REPLACING FLIP-UP Footboard Figure Adjusting Flip-Up FootboardReplacing Flip-Up Footboard ADJUSTING/REPLACING Rigid ANTI-TIPPER REPLACEMENT/ Adjustment FigureTubular Footrest Figure Replacing Front Elastomers Figure Elastomers and SuspensionPage Page Limited Warranty One Invacare Way Chedworth Way

Top End Terminator Jr specifications

The Invacare Top End Terminator Jr is a premier wheelchair designed specifically for young athletes, providing both performance and versatility. It caters to the needs of competitive youth athletes, ensuring superior functionality and comfort during sports activities. The Terminator Jr blends advanced technology with thoughtful design, allowing young users to experience the thrill of competitive racing.

One of the standout features of the Terminator Jr is its lightweight aluminum frame. This construction not only enhances portability but also ensures that the wheelchair is robust enough to withstand the rigors of competitive sports. The frame is designed to provide optimal rigidity and stability, which translates into improved performance during races.

The Terminator Jr boasts an adjustable camber. This feature allows users to modify the angle of the wheels for increased speed and maneuverability. By altering the camber, athletes can optimize their performance based on personal preference and training requirements, making it an adaptable choice for different racing conditions and environments.

Another significant aspect of the Terminator Jr is its high-quality wheels and tires. The wheelchair is equipped with specialized racing wheels that offer excellent traction and control on various surfaces. The tires are designed for speed while ensuring stability, contributing to a superior racing experience.

The seat and backrests of the Terminator Jr are designed with comfort and support in mind. The seating system is adjustable, allowing for customization according to the athlete’s size and needs. This level of personalization helps to prevent discomfort during long periods of use, enabling young athletes to focus entirely on their performance.

Additionally, the Terminator Jr includes a variety of accessory options, such as footrests and backrest supports, which can be tailored to the athlete's preferences. This adaptability is key in ensuring that the wheelchair meets the specific requirements of different sports and individual users.

Safety and durability are paramount in the design of the Invacare Top End Terminator Jr. Its superior construction ensures that it can handle the physical demands of competitive racing, providing athletes with peace of mind as they focus on their performance.

In summary, the Invacare Top End Terminator Jr is a cutting-edge racing wheelchair that emphasizes performance, comfort, and customization. With its lightweight aluminum frame, adjustable camber, high-quality wheels, and customizable seating, it stands out as an excellent choice for young athletes committed to excelling in their chosen sports.
Top Page Image Contents