Invacare Top End Terminator Jr manual ADJUSTING/REPLACING FLIP-UP Footboard Figure

Page 38

PROCEDURE 8

FOOTREST/ANTI-TIPPER

F O O T R E S T

A N T I

T

I

P P E R

This Procedure includes the following:

Adjusting/Replacing Flip-Up Footboard

Adjusting/Replacing Rigid Tubular Footrest

Anti-Tipper Replacement/Adjustment

WARNING

After ANY adjustments, repair or service and BEFORE use, make sure all attaching hardware is tightened securely - otherwise injury or dam- age may result.

ALWAYS perform this procedure in the presence of an assistant. The position of the footrest, cam- ber tube, back angle, the tautness of the back upholstery as well as the user's condition are di- rectly related to the wheelchairs stability. Any change to one (1) or any combination of the five (5) may cause the wheelchair to decrease in stability. Use EXTREME caution when using a new seating position.

Check ALL Allen Screws that secure the foot- rest/raised footrest system to the wheelchair frame to make sure they are securely tight- ened BEFORE using the wheelchair. ESPECIALLY if engaging in ANY vigorous activity.

The footrest assembly MUST be at least 1-3/4- inches above the ground/floor to avoid hitting protruding objects when using this wheelchair.

ADJUSTING/REPLACING FLIP-UP FOOTBOARD (FIGURE 1)

Adjusting Flip-Up Footboard

DEPTH.

1.Loosen the two (2) hex screws on each clamp securing the footboard to the wheelchair.

2.Slide the footboard mounting bar to the desired position.

3.Securely tighten the two (2) hex screws on each clamp secureing the footboard to the wheelchair.

HEIGHT.

1.Remove the hex bolts, locknuts, and coved washers seucring the footboard to the footboard mounting bar.

2.Reposition the footboard to the desired height.

3.Install the hex bolts, locknuts and coved washers through the footboard and footboard mounting bar as shown in FIGURE 1.

ANGLE.

1.Flip the footboard up.

2.Torque the angle adjustment screws:

IN (COUNTERCLOCKWISE) - to angle the footboard downward.

OUT (CLOCKWISE) - to angle the footboard upward.

NOTE: Ensure that both angle adjustment screws have the same number of threads showing.

3. Flip the footboard down.

Replacing Flip-Up Footboard

1.Loosen the two (2) hex screws on each clamp securing the footboard to the wheelchair.

2.Slide the EXISTING footboard mounting bars out of the clamps.

3.Slide the NEW footboard mounting bars into the clamps on the wheelchair frame.

4.Tighten the two (2) hex screws on the clamps to secure the footboard mounting bars to the wheel- chair frame.

ADJUSTING DEPTH AND HEIGHT/REPLACING

Clamp

Hex Screws

 

Wheelchair

Footboard

Frame

Mounting

 

 

Bar

 

Mounting

 

Holes

 

Locknut

 

Hex Screw

Footboard

Coved Washers

ADJUSTING ANGLE

Footboard

Angle Adjustment Screws

FIGURE 1 - ADJUSTING/REPLACING FLIP-UP

FOOTBOARD

38

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Terminator Junior JR Special Notes Table of Contents Specifications General Guidelines SAFETY/HANDLING Wheelchairs ProcedureCoping with Everyday Obstacles Percentage of Weight DistributionStability and Balance Reaching, Leaning Backwards Functional Reach From a WheelchairReaching, Leaning and Bending Forward TiltingStairways Transferring to and From Other SeatsSafety Inspection Checklist Initially Inspect Adjust Weekly Monthly PeriodicallyMaintenance Safety Precautions TroubleshootingMaintenance Suggested Maintenance ProceduresFolding the Back FOLDING/UNFOLDING the Back FigureChanging the Back Angle Figure Unfolding the BackBack Back Upholstery Cover Adjustable Tension StrapsReplacing Adjustable Tension Back Upholstery Slide the back canes out of the back uprightsReplacing the Locking Mechanism in the Back Cane Figure Back in this procedure of the manualReplacing the Spreader BAR Figure CaneInstalling the Stroller Handles Figure Installing the Stroller HandlesInstalling Using Cantilever Arms FigureINSTALLING/REMOVING Cantilever Arms Figure RemovingAdjusting Cantilever ARM Height Figure Adjusting Cantilever ARM Angle Figures 2Armrest Pad Replacement Armrest PAD ADJUSTMENT/ Replacement FigureArmrest Pad Adjustment Adjusting the T-ARMS Installing T-ARM Sockets FigureINSTALLING/REMOVING T-ARMS Figure Adjusting T-Arm Sockets Figure Adjusting T-Arm Depth FigureAdjusting T-Arm Width Figure Adjusting T-ARM Sockets Replacing the T-ARM Locking Lever FigureReplacing Seat PAN Figure Adjusting Rear Seat Height FigureAdjusting Seat Depth Figures 2 PerformSTEPS1-2 ofREPLACINGTHESEATPANA T Determining Frame Height Figure Adjusting Seat Width FigureAdjusting Front SEAT-TO-FLOOR Height Front Seat-to-floor Height Adjustment Ensure wheel locks engage properly. Refer toREMOVING/INSTALLING Rear Wheels Figure Adjusting QUICK-RELEASE Axles FigureHandrim Replacement Figure Adjusting QUAD-RELEASE Handles FigureInstalling QUAD-RELEASE Axles Figure Removing Play From Rear WheelsCamber Clamps REPAIRING/REPLACING Rear WHEEL, TIRE/TUBEOPENING/CLOSING Clamps Figure Receiver Tube ClampsAdjusting Rear Wheel Camber Figure Closed PositionDetermining Toe In/Toe Out Figures 8 DETERMINING/ADJUSTING TOE IN/TOE OUTAdjusting Toe In/Toe Out Figure Adjusting Wheelbase Length Figure ING TOE IN/TOE OUT inthisprocedureofthemanualAdjusting Wheelbase Width Figure Replacing Axle Tube FigureRepositioning the Axle Tube Figures 14 E E L S Replacing Front Casters Adjusting Front Caster Height FigureREPOSITIONING/REPLACING Front Casters Figure Repositioning Front CastersRepeat Steps 2-5 on the opposite front caster Wheel Lock ADJUSTMENT/ Replacement FigureRepeat this procedure for the opposite wheel lock Engage the wheel lockReplacing Flip-Up Footboard ADJUSTING/REPLACING FLIP-UP Footboard FigureAdjusting Flip-Up Footboard Tubular Footrest Figure ADJUSTING/REPLACING RigidANTI-TIPPER REPLACEMENT/ Adjustment Figure Elastomers and Suspension Replacing Front Elastomers FigurePage Page Limited Warranty One Invacare Way Chedworth Way

Top End Terminator Jr specifications

The Invacare Top End Terminator Jr is a premier wheelchair designed specifically for young athletes, providing both performance and versatility. It caters to the needs of competitive youth athletes, ensuring superior functionality and comfort during sports activities. The Terminator Jr blends advanced technology with thoughtful design, allowing young users to experience the thrill of competitive racing.

One of the standout features of the Terminator Jr is its lightweight aluminum frame. This construction not only enhances portability but also ensures that the wheelchair is robust enough to withstand the rigors of competitive sports. The frame is designed to provide optimal rigidity and stability, which translates into improved performance during races.

The Terminator Jr boasts an adjustable camber. This feature allows users to modify the angle of the wheels for increased speed and maneuverability. By altering the camber, athletes can optimize their performance based on personal preference and training requirements, making it an adaptable choice for different racing conditions and environments.

Another significant aspect of the Terminator Jr is its high-quality wheels and tires. The wheelchair is equipped with specialized racing wheels that offer excellent traction and control on various surfaces. The tires are designed for speed while ensuring stability, contributing to a superior racing experience.

The seat and backrests of the Terminator Jr are designed with comfort and support in mind. The seating system is adjustable, allowing for customization according to the athlete’s size and needs. This level of personalization helps to prevent discomfort during long periods of use, enabling young athletes to focus entirely on their performance.

Additionally, the Terminator Jr includes a variety of accessory options, such as footrests and backrest supports, which can be tailored to the athlete's preferences. This adaptability is key in ensuring that the wheelchair meets the specific requirements of different sports and individual users.

Safety and durability are paramount in the design of the Invacare Top End Terminator Jr. Its superior construction ensures that it can handle the physical demands of competitive racing, providing athletes with peace of mind as they focus on their performance.

In summary, the Invacare Top End Terminator Jr is a cutting-edge racing wheelchair that emphasizes performance, comfort, and customization. With its lightweight aluminum frame, adjustable camber, high-quality wheels, and customizable seating, it stands out as an excellent choice for young athletes committed to excelling in their chosen sports.
Top Page Image Contents