Invacare Top End Terminator Jr manual REPOSITIONING/REPLACING Front Casters Figure

Page 36

PROCEDURE 7

WHEELS

W

H

E

E

L

S

REPOSITIONING/REPLACING FRONT CASTERS (FIGURE 14)

CAUTION

Replacing/repositioning the front casters can af- fect the performance of the wheelchair. Contact Invacare at the telephone numbers on the back of this manualBEFOREperformingthisprocedure.

Replacing Front Casters

NOTE: Both casters should be the same size.

1.Removetheboltandlocknutthatsecurethefrontcaster to the fork.

2.Remove front caster and axle spacers from fork.

3.Install NEW front caster and spacers onto the fork and securely tighten with the bolt and locknut.

4.RepeatSTEPS1-3foroppositefrontcasterifnecessary.

NOTE: WHEELCHAIRS WITH STANDARD FORKS: If replacing front casters with a different size than what was originallyonthewheelchair,thefrontcasterheightMUSTbe adjusted to keep the wheelchair frame parallel to the floor. Refer to ADJUSTING FRONT CASTER HEIGHT in this procedure of the manual ONLY after contacting Invacare.

NOTE: WHEELCHAIRS WITH SUSPENSION FORKS: If replacing front casters with a different size than what was originally on the wheelchair, the front caster height MUST be adjusted to keep the wheelchair frame parallel to the floor. Proceed to REPOSITIONING FRONT CASTERS in this procedure of the manual.

STANDARD FORKS

Fork

Locknut

 

Bolt

 

 

Spacer

Spacer

Caster

 

SUSPENSION FORKS

Fork

Locknut

Bolt

 

 

Axle

 

Spacer

Axle

Caster

Spacer

FIGURE 14 - REPOSITIONING/REPLACING FRONT

 

CASTERS

Repositioning Front Casters

NOTE: This procedure is for wheelchairs with suspension forks ONLY.

1.Remove the bolt and locknut that secure the caster and axle spacers to the fork.

2.Install the caster, bolt, locknut and axle spacers onto the fork in the desired mounting position. Tighten securely.

3.Repeat STEPS 1-2 for the opposite caster if neces- sary.

NOTE: If the casters have been repositioned and the wheelchair frame is not parallel to the floor, the caster height MUST be adjusted. Refer to ADJUSTING FRONT CASTER HEIGHT in this procedure of the manual.

ADJUSTING FRONT CASTER HEIGHT (FIGURE 15)

CAUTION

Changing the height of the front casters can af- fect the performance of the wheelchair. Contact Invacare at the telephone numbers on the back of this manual BEFORE performing this procedure.

NOTE: When changing the seat-to-floor height, the rear wheel/front caster size and/or the original degree of cam- ber of the wheelchair, it becomes necessary to adjust the front caster height so the wheelchair frame will remain par- allel to the floor.

1.Place the wheelchair on a flat surface.

2.Loosen the locknut securing the caster headtube.

3.Position a large right triangle or "L" square on the flat surface and against the caster headtube.

4.Adjust the height of the front caster by sliding the fork stem up or down until the caster headtube is flush against the right triangle or "L" square.

36

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Terminator Junior JR Special Notes Table of Contents Specifications General Guidelines SAFETY/HANDLING Wheelchairs ProcedurePercentage of Weight Distribution Stability and BalanceCoping with Everyday Obstacles Functional Reach From a Wheelchair Reaching, Leaning and Bending ForwardReaching, Leaning Backwards TiltingStairways Transferring to and From Other SeatsSafety Inspection Checklist Initially Inspect Adjust Weekly Monthly PeriodicallyTroubleshooting MaintenanceMaintenance Safety Precautions Suggested Maintenance ProceduresFOLDING/UNFOLDING the Back Figure Changing the Back Angle FigureFolding the Back Unfolding the BackBack Adjustable Tension Straps Replacing Adjustable Tension Back UpholsteryBack Upholstery Cover Slide the back canes out of the back uprightsBack in this procedure of the manual Replacing the Spreader BAR FigureReplacing the Locking Mechanism in the Back Cane Figure CaneInstalling the Stroller Handles Figure Installing the Stroller HandlesUsing Cantilever Arms Figure INSTALLING/REMOVING Cantilever Arms FigureInstalling RemovingAdjusting Cantilever ARM Height Figure Adjusting Cantilever ARM Angle Figures 2Armrest PAD ADJUSTMENT/ Replacement Figure Armrest Pad AdjustmentArmrest Pad Replacement Installing T-ARM Sockets Figure INSTALLING/REMOVING T-ARMS FigureAdjusting the T-ARMS Adjusting T-Arm Depth Figure Adjusting T-Arm Width FigureAdjusting T-Arm Sockets Figure Adjusting T-ARM Sockets Replacing the T-ARM Locking Lever FigureAdjusting Rear Seat Height Figure Adjusting Seat Depth Figures 2Replacing Seat PAN Figure PerformSTEPS1-2 ofREPLACINGTHESEATPANA T Adjusting Seat Width Figure Adjusting Front SEAT-TO-FLOOR HeightDetermining Frame Height Figure Front Seat-to-floor Height Adjustment Ensure wheel locks engage properly. Refer toREMOVING/INSTALLING Rear Wheels Figure Adjusting QUICK-RELEASE Axles FigureAdjusting QUAD-RELEASE Handles Figure Installing QUAD-RELEASE Axles FigureHandrim Replacement Figure Removing Play From Rear WheelsREPAIRING/REPLACING Rear WHEEL, TIRE/TUBE OPENING/CLOSING Clamps FigureCamber Clamps Receiver Tube ClampsAdjusting Rear Wheel Camber Figure Closed PositionDETERMINING/ADJUSTING TOE IN/TOE OUT Adjusting Toe In/Toe Out FigureDetermining Toe In/Toe Out Figures 8 Adjusting Wheelbase Length Figure ING TOE IN/TOE OUT inthisprocedureofthemanualAdjusting Wheelbase Width Figure Replacing Axle Tube FigureRepositioning the Axle Tube Figures 14 E E L S Adjusting Front Caster Height Figure REPOSITIONING/REPLACING Front Casters FigureReplacing Front Casters Repositioning Front CastersWheel Lock ADJUSTMENT/ Replacement Figure Repeat this procedure for the opposite wheel lockRepeat Steps 2-5 on the opposite front caster Engage the wheel lockADJUSTING/REPLACING FLIP-UP Footboard Figure Adjusting Flip-Up FootboardReplacing Flip-Up Footboard ADJUSTING/REPLACING Rigid ANTI-TIPPER REPLACEMENT/ Adjustment FigureTubular Footrest Figure Elastomers and Suspension Replacing Front Elastomers FigurePage Page Limited Warranty One Invacare Way Chedworth Way

Top End Terminator Jr specifications

The Invacare Top End Terminator Jr is a premier wheelchair designed specifically for young athletes, providing both performance and versatility. It caters to the needs of competitive youth athletes, ensuring superior functionality and comfort during sports activities. The Terminator Jr blends advanced technology with thoughtful design, allowing young users to experience the thrill of competitive racing.

One of the standout features of the Terminator Jr is its lightweight aluminum frame. This construction not only enhances portability but also ensures that the wheelchair is robust enough to withstand the rigors of competitive sports. The frame is designed to provide optimal rigidity and stability, which translates into improved performance during races.

The Terminator Jr boasts an adjustable camber. This feature allows users to modify the angle of the wheels for increased speed and maneuverability. By altering the camber, athletes can optimize their performance based on personal preference and training requirements, making it an adaptable choice for different racing conditions and environments.

Another significant aspect of the Terminator Jr is its high-quality wheels and tires. The wheelchair is equipped with specialized racing wheels that offer excellent traction and control on various surfaces. The tires are designed for speed while ensuring stability, contributing to a superior racing experience.

The seat and backrests of the Terminator Jr are designed with comfort and support in mind. The seating system is adjustable, allowing for customization according to the athlete’s size and needs. This level of personalization helps to prevent discomfort during long periods of use, enabling young athletes to focus entirely on their performance.

Additionally, the Terminator Jr includes a variety of accessory options, such as footrests and backrest supports, which can be tailored to the athlete's preferences. This adaptability is key in ensuring that the wheelchair meets the specific requirements of different sports and individual users.

Safety and durability are paramount in the design of the Invacare Top End Terminator Jr. Its superior construction ensures that it can handle the physical demands of competitive racing, providing athletes with peace of mind as they focus on their performance.

In summary, the Invacare Top End Terminator Jr is a cutting-edge racing wheelchair that emphasizes performance, comfort, and customization. With its lightweight aluminum frame, adjustable camber, high-quality wheels, and customizable seating, it stands out as an excellent choice for young athletes committed to excelling in their chosen sports.
Top Page Image Contents