Invacare Top End Terminator Jr manual REPAIRING/REPLACING Rear WHEEL, TIRE/TUBE, Camber Clamps

Page 29

WHEELS

PROCEDURE 7

WARNING

Tire MUST be FULLY deflated BEFORE any disas- sembly procedures are performed. Otherwise injury or damage may result.

2.Remove all air from the tube by pressing down on the pin in the center of the valve stem.

3.While carefully holding the tire, tube and rim strip to one side, hold the allen screws and remove the lock- nuts that secure the handrim to the rear wheel.

4.Remove the EXISTING handrim.

5.Install NEW handrim by reversing STEPS 2-4.

WARNING

DO NOT inflate tire untilitiscompletelyassembled. Otherwise injury or damage may result.

6.Inflate tire to correct psi rating on the sidewall of tire.

7.Reinstall rear wheel to the wheelchair. Refer to RE- MOVING/INSTALLING REAR WHEELS in this pro- cedure of the manual.

8.Repeat STEPS 1-7 for opposite rear wheel if necessary.

Allen

Screw

Handrim

Locknut

FIGURE 5 - HANDRIM REPLACEMENT

REPAIRING/REPLACING REAR WHEEL, TIRE/TUBE

WARNING

Replacement of the tire or tube MUST be per- formed by a qualified technician.

CAUTION

Changing the size of the rear wheels can affect the performance of the wheelchair. Contact In- vacare at the numbers on the back cover BE- FORE performing this procedure.

NOTE: If replacing rear wheels with a different size than whatwasoriginallyonthe wheelchair,thefrontcasterheight must also be changed to keep the wheelchair frame parallel to the floor. Refer to ADJUSTING FRONT CASTER HEIGHT in this procedure of the manual ONLY after con- tacting Invacare. Anti-tipper height (if applicable) must also be adjusted to maintain 1-1/2 to 2-inch clearance between bottom of the anti-tipper wheels and the floor. Refer toANTI- TIPPER REPLACEMENT/ADJUSTMENT in PROCE- DURE 8 of this manual.

OPENING/CLOSING CLAMPS (FIGURE 6)

WARNING

QUICK RELEASE LEVERS - Make sure the quick re- lease levers are in the CLOSED position BEFORE using the wheelchair, otherwise personal injury or damage to the wheelchair may result.

STANDARD CAMBER OR RECEIVER TUBE CLAMPS - Make sure the hex screws and locknuts are se- curely tightened BEFORE using the wheelchair, otherwise personal injury or damage to the wheelchair may result.

CAUTION

DONOTclosethequick-releaseleversortightenthe hex screws and locknuts without camber inserts in the axle tube. Damage to the axle tube will occur.

Camber Clamps

1.Performone(1)ofthefollowingtoopenacamberclamp:

A.QUICK RELEASE LEVERS - Pull the quick re- lease lever to the open position.

B.STANDARD CAMBER CLAMPS - Loosen, but do not remove the hex screw and locknut on the camber clamp.

2.Performone(1)ofthefollowingtocloseacamberclamp:

A.QUICK RELEASE LEVERS - Push the quick release lever on the camber clamps to the closed position.

B.STANDARDCAMBERCLAMPS-Securelytighten the hex screw and locknut to secure the axle tube.

Receiver Tube Clamps

NOTE: The receiver tube clamps are used ONLY to adjust wheelbase length.

1.Perform one (1) of the following to open a receiver tube clamp:

A.QUICK RELEASE LEVERS - Pull the quick re- lease levers on the receiver tube clamps to the open position.

B.STANDARD RECEIVER TUBE CLAMPS - Loosen, but do not remove the hex screws and locknuts on the receiver tube clamps.

2.Perfrom one (1) of the following to close a receiver tube clamp:

A.QUICK RELEASE LEVERS - Push the quick release lever on the receiver tube clamps to the closed position.

B.STANDARD RECEIVER TUBE CLAMPS - Tighten the hex screw and locknut on the receiver tube clamp.

W

H

E

E

L

S

29

Image 29
Contents Terminator Junior JR Special Notes Table of Contents Specifications General Guidelines Procedure SAFETY/HANDLING WheelchairsCoping with Everyday Obstacles Percentage of Weight DistributionStability and Balance Reaching, Leaning and Bending Forward Functional Reach From a WheelchairReaching, Leaning Backwards TiltingTransferring to and From Other Seats StairwaysInitially Inspect Adjust Weekly Monthly Periodically Safety Inspection ChecklistMaintenance TroubleshootingMaintenance Safety Precautions Suggested Maintenance ProceduresChanging the Back Angle Figure FOLDING/UNFOLDING the Back FigureFolding the Back Unfolding the BackBack Replacing Adjustable Tension Back Upholstery Adjustable Tension StrapsBack Upholstery Cover Slide the back canes out of the back uprightsReplacing the Spreader BAR Figure Back in this procedure of the manualReplacing the Locking Mechanism in the Back Cane Figure CaneInstalling the Stroller Handles Installing the Stroller Handles FigureINSTALLING/REMOVING Cantilever Arms Figure Using Cantilever Arms FigureInstalling RemovingAdjusting Cantilever ARM Angle Figures 2 Adjusting Cantilever ARM Height FigureArmrest Pad Replacement Armrest PAD ADJUSTMENT/ Replacement FigureArmrest Pad Adjustment Adjusting the T-ARMS Installing T-ARM Sockets FigureINSTALLING/REMOVING T-ARMS Figure Adjusting T-Arm Sockets Figure Adjusting T-Arm Depth FigureAdjusting T-Arm Width Figure Replacing the T-ARM Locking Lever Figure Adjusting T-ARM SocketsAdjusting Seat Depth Figures 2 Adjusting Rear Seat Height FigureReplacing Seat PAN Figure PerformSTEPS1-2 ofREPLACINGTHESEATPANA T Determining Frame Height Figure Adjusting Seat Width FigureAdjusting Front SEAT-TO-FLOOR Height Ensure wheel locks engage properly. Refer to Front Seat-to-floor Height AdjustmentAdjusting QUICK-RELEASE Axles Figure REMOVING/INSTALLING Rear Wheels FigureInstalling QUAD-RELEASE Axles Figure Adjusting QUAD-RELEASE Handles FigureHandrim Replacement Figure Removing Play From Rear WheelsOPENING/CLOSING Clamps Figure REPAIRING/REPLACING Rear WHEEL, TIRE/TUBECamber Clamps Receiver Tube ClampsClosed Position Adjusting Rear Wheel Camber FigureDetermining Toe In/Toe Out Figures 8 DETERMINING/ADJUSTING TOE IN/TOE OUTAdjusting Toe In/Toe Out Figure ING TOE IN/TOE OUT inthisprocedureofthemanual Adjusting Wheelbase Length FigureReplacing Axle Tube Figure Adjusting Wheelbase Width FigureRepositioning the Axle Tube Figures 14 E E L S REPOSITIONING/REPLACING Front Casters Figure Adjusting Front Caster Height FigureReplacing Front Casters Repositioning Front CastersRepeat this procedure for the opposite wheel lock Wheel Lock ADJUSTMENT/ Replacement FigureRepeat Steps 2-5 on the opposite front caster Engage the wheel lockReplacing Flip-Up Footboard ADJUSTING/REPLACING FLIP-UP Footboard FigureAdjusting Flip-Up Footboard Tubular Footrest Figure ADJUSTING/REPLACING RigidANTI-TIPPER REPLACEMENT/ Adjustment Figure Replacing Front Elastomers Figure Elastomers and SuspensionPage Page Limited Warranty One Invacare Way Chedworth Way

Top End Terminator Jr specifications

The Invacare Top End Terminator Jr is a premier wheelchair designed specifically for young athletes, providing both performance and versatility. It caters to the needs of competitive youth athletes, ensuring superior functionality and comfort during sports activities. The Terminator Jr blends advanced technology with thoughtful design, allowing young users to experience the thrill of competitive racing.

One of the standout features of the Terminator Jr is its lightweight aluminum frame. This construction not only enhances portability but also ensures that the wheelchair is robust enough to withstand the rigors of competitive sports. The frame is designed to provide optimal rigidity and stability, which translates into improved performance during races.

The Terminator Jr boasts an adjustable camber. This feature allows users to modify the angle of the wheels for increased speed and maneuverability. By altering the camber, athletes can optimize their performance based on personal preference and training requirements, making it an adaptable choice for different racing conditions and environments.

Another significant aspect of the Terminator Jr is its high-quality wheels and tires. The wheelchair is equipped with specialized racing wheels that offer excellent traction and control on various surfaces. The tires are designed for speed while ensuring stability, contributing to a superior racing experience.

The seat and backrests of the Terminator Jr are designed with comfort and support in mind. The seating system is adjustable, allowing for customization according to the athlete’s size and needs. This level of personalization helps to prevent discomfort during long periods of use, enabling young athletes to focus entirely on their performance.

Additionally, the Terminator Jr includes a variety of accessory options, such as footrests and backrest supports, which can be tailored to the athlete's preferences. This adaptability is key in ensuring that the wheelchair meets the specific requirements of different sports and individual users.

Safety and durability are paramount in the design of the Invacare Top End Terminator Jr. Its superior construction ensures that it can handle the physical demands of competitive racing, providing athletes with peace of mind as they focus on their performance.

In summary, the Invacare Top End Terminator Jr is a cutting-edge racing wheelchair that emphasizes performance, comfort, and customization. With its lightweight aluminum frame, adjustable camber, high-quality wheels, and customizable seating, it stands out as an excellent choice for young athletes committed to excelling in their chosen sports.