Invacare Top End Terminator Jr FOLDING/UNFOLDING the Back Figure, Changing the Back Angle Figure

Page 12

PROCEDURE 4

BACK

B A C K

This Procedure includes the following:

Folding/Unfolding the Back

Changing the Back Angle

Adjusting the Back Height

Replacing Standard Back Upholstery

Replacing Custom Manual Adjustable Tension Back Upholstery

Replacing the Spreader Bar

Replacing the Locking Mechanism in the Back Cane Installing the Stroller Handles

WARNING

ALWAYS perform this procedure in the presence of an assistant. The position of the footrest, camber tube, back angle, the tautness of the back uphol- stery as well as the user's condition are directly re- lated to the wheelchairs stability. Any change to one(1)oranycombinationofthefive(5)maycause thewheelchairtodecreaseinstability.UseEXTREME caution when using a new seating position.

AfterANYadjustments,repairorserviceandBEFORE use,makesure all attaching hardware is tightened securely - otherwise injury or damage may result.

FOLDING/UNFOLDING THE BACK (FIGURE 1)

WARNING

Back MUST be locked securely in place and all at- tachinghardwaretightBEFOREusingthewheelchair.

Folding the Back

1.Pull BOTH back release levers UP.

2.While holding BOTH back release levers, push the back canes DOWN.

Unfolding the Back

1.Pull the back canes UP towards the rear of the wheelchair there is an audible "click".

2.Push the back canes FORWARD to ensure they are locked in place.

3.If the back canes are not locked in place, repeat STEPS 1-2 until the back canes lock.

Back Cane

Back

Release

Lever

FIGURE 1 - FOLDING/UNFOLDING THE BACK

CHANGING THE BACK ANGLE (FIGURE 2)

WARNING

The following procedure MUST be performed by a qualified technician.

1.Remove the seat pan. Refer to REPLACING SEAT PAN in PROCEDURE 6 of this manual.

2.Loosen, but do not remove the rear hex screw that secures the back angle plate to the wheel- chair frame.

3.Remove the front hex screw, washers, coved washer and locknut that secure the back angle plate to the wheelchair frame.

4.Position the back angle plate to one (1) of six (6) back angles shown in FIGURE 2.

5.Reinstall the front hex screw, washers and coved washer and securely tighten with locknut. Refer to FIGURE 2 for correct hardware orientation.

6.Securely tighten the rear hex screw that secures the back adjustment plate to the wheelchair frame.

7.If wheelchair is equipped with cantilever arms, adjust the angle of the cantilever arm so they re- main parallel to the ground/floor. Refer to ADJUST- ING CANTILEVER ARM ANGLE in PROCEDURE 5 of this manual.

Wheelchair

Seat Pan

 

Frame

 

Rear Hex

Coved Washer

Screw

(Loosen,

Locknut

but do not

 

Remove)

Washer

 

Back

 

Angle

 

Plate

 

Washer

BACK

Front

ANGLES

86°

Hex

90°

Screw

94°

 

 

98°

 

102°

 

106°

FIGURE 2 - CHANGING THE BACK ANGLE

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Terminator Junior JR Special Notes Table of Contents Specifications General Guidelines SAFETY/HANDLING Wheelchairs ProcedurePercentage of Weight Distribution Stability and BalanceCoping with Everyday Obstacles Functional Reach From a Wheelchair Reaching, Leaning and Bending ForwardReaching, Leaning Backwards TiltingStairways Transferring to and From Other SeatsSafety Inspection Checklist Initially Inspect Adjust Weekly Monthly PeriodicallyTroubleshooting MaintenanceMaintenance Safety Precautions Suggested Maintenance ProceduresFOLDING/UNFOLDING the Back Figure Changing the Back Angle FigureFolding the Back Unfolding the BackBack Adjustable Tension Straps Replacing Adjustable Tension Back UpholsteryBack Upholstery Cover Slide the back canes out of the back uprightsBack in this procedure of the manual Replacing the Spreader BAR FigureReplacing the Locking Mechanism in the Back Cane Figure CaneInstalling the Stroller Handles Figure Installing the Stroller HandlesUsing Cantilever Arms Figure INSTALLING/REMOVING Cantilever Arms FigureInstalling RemovingAdjusting Cantilever ARM Height Figure Adjusting Cantilever ARM Angle Figures 2Armrest PAD ADJUSTMENT/ Replacement Figure Armrest Pad AdjustmentArmrest Pad Replacement Installing T-ARM Sockets Figure INSTALLING/REMOVING T-ARMS FigureAdjusting the T-ARMS Adjusting T-Arm Depth Figure Adjusting T-Arm Width FigureAdjusting T-Arm Sockets Figure Adjusting T-ARM Sockets Replacing the T-ARM Locking Lever FigureAdjusting Rear Seat Height Figure Adjusting Seat Depth Figures 2Replacing Seat PAN Figure PerformSTEPS1-2 ofREPLACINGTHESEATPANA T Adjusting Seat Width Figure Adjusting Front SEAT-TO-FLOOR HeightDetermining Frame Height Figure Front Seat-to-floor Height Adjustment Ensure wheel locks engage properly. Refer toREMOVING/INSTALLING Rear Wheels Figure Adjusting QUICK-RELEASE Axles FigureAdjusting QUAD-RELEASE Handles Figure Installing QUAD-RELEASE Axles FigureHandrim Replacement Figure Removing Play From Rear WheelsREPAIRING/REPLACING Rear WHEEL, TIRE/TUBE OPENING/CLOSING Clamps FigureCamber Clamps Receiver Tube ClampsAdjusting Rear Wheel Camber Figure Closed PositionDETERMINING/ADJUSTING TOE IN/TOE OUT Adjusting Toe In/Toe Out FigureDetermining Toe In/Toe Out Figures 8 Adjusting Wheelbase Length Figure ING TOE IN/TOE OUT inthisprocedureofthemanualAdjusting Wheelbase Width Figure Replacing Axle Tube FigureRepositioning the Axle Tube Figures 14 E E L S Adjusting Front Caster Height Figure REPOSITIONING/REPLACING Front Casters FigureReplacing Front Casters Repositioning Front CastersWheel Lock ADJUSTMENT/ Replacement Figure Repeat this procedure for the opposite wheel lockRepeat Steps 2-5 on the opposite front caster Engage the wheel lockADJUSTING/REPLACING FLIP-UP Footboard Figure Adjusting Flip-Up FootboardReplacing Flip-Up Footboard ADJUSTING/REPLACING Rigid ANTI-TIPPER REPLACEMENT/ Adjustment FigureTubular Footrest Figure Elastomers and Suspension Replacing Front Elastomers FigurePage Page Limited Warranty One Invacare Way Chedworth Way

Top End Terminator Jr specifications

The Invacare Top End Terminator Jr is a premier wheelchair designed specifically for young athletes, providing both performance and versatility. It caters to the needs of competitive youth athletes, ensuring superior functionality and comfort during sports activities. The Terminator Jr blends advanced technology with thoughtful design, allowing young users to experience the thrill of competitive racing.

One of the standout features of the Terminator Jr is its lightweight aluminum frame. This construction not only enhances portability but also ensures that the wheelchair is robust enough to withstand the rigors of competitive sports. The frame is designed to provide optimal rigidity and stability, which translates into improved performance during races.

The Terminator Jr boasts an adjustable camber. This feature allows users to modify the angle of the wheels for increased speed and maneuverability. By altering the camber, athletes can optimize their performance based on personal preference and training requirements, making it an adaptable choice for different racing conditions and environments.

Another significant aspect of the Terminator Jr is its high-quality wheels and tires. The wheelchair is equipped with specialized racing wheels that offer excellent traction and control on various surfaces. The tires are designed for speed while ensuring stability, contributing to a superior racing experience.

The seat and backrests of the Terminator Jr are designed with comfort and support in mind. The seating system is adjustable, allowing for customization according to the athlete’s size and needs. This level of personalization helps to prevent discomfort during long periods of use, enabling young athletes to focus entirely on their performance.

Additionally, the Terminator Jr includes a variety of accessory options, such as footrests and backrest supports, which can be tailored to the athlete's preferences. This adaptability is key in ensuring that the wheelchair meets the specific requirements of different sports and individual users.

Safety and durability are paramount in the design of the Invacare Top End Terminator Jr. Its superior construction ensures that it can handle the physical demands of competitive racing, providing athletes with peace of mind as they focus on their performance.

In summary, the Invacare Top End Terminator Jr is a cutting-edge racing wheelchair that emphasizes performance, comfort, and customization. With its lightweight aluminum frame, adjustable camber, high-quality wheels, and customizable seating, it stands out as an excellent choice for young athletes committed to excelling in their chosen sports.
Top Page Image Contents