Invacare Top End Terminator Jr manual Troubleshooting, Maintenance Safety Precautions

Page 11

TROUBLESHOOTING/MAINTENANCE

PROCEDURE 3

This Procedure includes the following:

Troubleshooting

Maintenance

TROUBLESHOOTING

CHAIR

CHAIR

SLUGGISH

CASTER

SQUEAKS

LOOSENESS

SOLUTIONS

VEERS

VEERS

TURN OR

FLUTTERS

AND

IN CHAIR

 

RIGHT

LEFT

PERFORMANCE

 

RATTLES

 

 

 

 

 

 

 

 

 

X

X

X

X

 

 

Check tires for correct

 

 

 

 

 

 

and equal pressure.

 

 

 

 

 

 

 

 

 

X

X

X

X

Check for loose stem nuts.

 

 

 

 

 

 

 

 

 

 

 

X

X

Check spokes and nipples.

 

 

 

 

 

 

 

X

X

 

X

 

 

Check that both casters

 

 

 

 

 

 

contact the ground at the

 

 

 

 

 

 

same time.

 

 

 

 

 

 

 

T R O U B L E S H O O T I N G

MAINTENANCE

Maintenance Safety Precautions

WARNING

AfterANYadjustments,repairorserviceandBEFORE use, make sure all attaching hardware is tightened securely - otherwise injury or damage may result.

CAUTION

DO NOT overtighten hardware attaching to the frame. This could cause damage to the frame tubing.

Suggested Maintenance Procedures

1.Before using your wheelchair, make sure all nuts and bolts are tight. Check all parts for damage or wear and replace. Check all parts for proper adjustment.

2.Keep quick/quad-release axles free of dirt and lint to ensure positive locking and proper operation. Refer to ADJUSTING QUICK-RELEASE AXLES or AD- JUSTING QUAD-RELEASE HANDLES in PROCE- DURE 7 of this manual.

3.Oil quick-release axles at least once (1) a month (3- in-1 oil® or equivalent).

WARNING

DO NOT use your wheelchair unless it has the proper tire pressure (p.s.i.). DO NOT overinflate the tires. Failure to follow these suggestions may cause the tire to explode and cause bodily harm.

4.Recommended tire pressure is listed on the sidewall of the tire.

CAUTION

As with any vehicle, the wheel s and tires should be checked periodically for cracks and wear, and should be replaced.

5.Check the wheels and tires periodically for cracks and wear. If damaged, have them replaced by a quali- fied technician.

6.Regularly check for loose spokes in the rear wheels. If loose, have them adjusted by a qualified technician.

7.Periodically check handrims to ensure they are se- cured to the rear wheels. Refer to HANDRIM RE- PLACEMENT in PROCEDURE 7 of this manual.

8.Periodically adjust wheel locks in correlation to tire wear. Refer to WHEEL LOCK ADJUSTMENT/RE- PLACEMENT in PROCEDURE 7 of this manual.

9.Periodically check caster wheel bearings to make

sure they are clean and free from moisture. Use a Teflon® lubricant if necessary.

10.FRONT SUSPENSION FORKS (if equipped) - Peri- odically lubricate the the inside of the elastomers and the shaft of the hex bolt that secures the elastomers to the suspension tube with a silicone based lubricant.

11.Check upholstery for sagging, rips or tears.

M A I N T E N A N C E

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Terminator Junior JR Special Notes Table of Contents Specifications General Guidelines Procedure SAFETY/HANDLING WheelchairsCoping with Everyday Obstacles Percentage of Weight DistributionStability and Balance Tilting Functional Reach From a WheelchairReaching, Leaning and Bending Forward Reaching, Leaning BackwardsTransferring to and From Other Seats StairwaysInitially Inspect Adjust Weekly Monthly Periodically Safety Inspection ChecklistSuggested Maintenance Procedures TroubleshootingMaintenance Maintenance Safety PrecautionsUnfolding the Back FOLDING/UNFOLDING the Back FigureChanging the Back Angle Figure Folding the BackBack Slide the back canes out of the back uprights Adjustable Tension StrapsReplacing Adjustable Tension Back Upholstery Back Upholstery CoverCane Back in this procedure of the manualReplacing the Spreader BAR Figure Replacing the Locking Mechanism in the Back Cane FigureInstalling the Stroller Handles Installing the Stroller Handles FigureRemoving Using Cantilever Arms FigureINSTALLING/REMOVING Cantilever Arms Figure InstallingAdjusting Cantilever ARM Angle Figures 2 Adjusting Cantilever ARM Height FigureArmrest Pad Replacement Armrest PAD ADJUSTMENT/ Replacement FigureArmrest Pad Adjustment Adjusting the T-ARMS Installing T-ARM Sockets FigureINSTALLING/REMOVING T-ARMS Figure Adjusting T-Arm Sockets Figure Adjusting T-Arm Depth FigureAdjusting T-Arm Width Figure Replacing the T-ARM Locking Lever Figure Adjusting T-ARM SocketsPerformSTEPS1-2 ofREPLACINGTHESEATPAN Adjusting Rear Seat Height FigureAdjusting Seat Depth Figures 2 Replacing Seat PAN FigureA T Determining Frame Height Figure Adjusting Seat Width FigureAdjusting Front SEAT-TO-FLOOR Height Ensure wheel locks engage properly. Refer to Front Seat-to-floor Height AdjustmentAdjusting QUICK-RELEASE Axles Figure REMOVING/INSTALLING Rear Wheels FigureRemoving Play From Rear Wheels Adjusting QUAD-RELEASE Handles FigureInstalling QUAD-RELEASE Axles Figure Handrim Replacement FigureReceiver Tube Clamps REPAIRING/REPLACING Rear WHEEL, TIRE/TUBEOPENING/CLOSING Clamps Figure Camber ClampsClosed Position Adjusting Rear Wheel Camber FigureDetermining Toe In/Toe Out Figures 8 DETERMINING/ADJUSTING TOE IN/TOE OUTAdjusting Toe In/Toe Out Figure ING TOE IN/TOE OUT inthisprocedureofthemanual Adjusting Wheelbase Length FigureReplacing Axle Tube Figure Adjusting Wheelbase Width FigureRepositioning the Axle Tube Figures 14 E E L S Repositioning Front Casters Adjusting Front Caster Height FigureREPOSITIONING/REPLACING Front Casters Figure Replacing Front CastersEngage the wheel lock Wheel Lock ADJUSTMENT/ Replacement FigureRepeat this procedure for the opposite wheel lock Repeat Steps 2-5 on the opposite front casterReplacing Flip-Up Footboard ADJUSTING/REPLACING FLIP-UP Footboard FigureAdjusting Flip-Up Footboard Tubular Footrest Figure ADJUSTING/REPLACING RigidANTI-TIPPER REPLACEMENT/ Adjustment Figure Replacing Front Elastomers Figure Elastomers and SuspensionPage Page Limited Warranty One Invacare Way Chedworth Way

Top End Terminator Jr specifications

The Invacare Top End Terminator Jr is a premier wheelchair designed specifically for young athletes, providing both performance and versatility. It caters to the needs of competitive youth athletes, ensuring superior functionality and comfort during sports activities. The Terminator Jr blends advanced technology with thoughtful design, allowing young users to experience the thrill of competitive racing.

One of the standout features of the Terminator Jr is its lightweight aluminum frame. This construction not only enhances portability but also ensures that the wheelchair is robust enough to withstand the rigors of competitive sports. The frame is designed to provide optimal rigidity and stability, which translates into improved performance during races.

The Terminator Jr boasts an adjustable camber. This feature allows users to modify the angle of the wheels for increased speed and maneuverability. By altering the camber, athletes can optimize their performance based on personal preference and training requirements, making it an adaptable choice for different racing conditions and environments.

Another significant aspect of the Terminator Jr is its high-quality wheels and tires. The wheelchair is equipped with specialized racing wheels that offer excellent traction and control on various surfaces. The tires are designed for speed while ensuring stability, contributing to a superior racing experience.

The seat and backrests of the Terminator Jr are designed with comfort and support in mind. The seating system is adjustable, allowing for customization according to the athlete’s size and needs. This level of personalization helps to prevent discomfort during long periods of use, enabling young athletes to focus entirely on their performance.

Additionally, the Terminator Jr includes a variety of accessory options, such as footrests and backrest supports, which can be tailored to the athlete's preferences. This adaptability is key in ensuring that the wheelchair meets the specific requirements of different sports and individual users.

Safety and durability are paramount in the design of the Invacare Top End Terminator Jr. Its superior construction ensures that it can handle the physical demands of competitive racing, providing athletes with peace of mind as they focus on their performance.

In summary, the Invacare Top End Terminator Jr is a cutting-edge racing wheelchair that emphasizes performance, comfort, and customization. With its lightweight aluminum frame, adjustable camber, high-quality wheels, and customizable seating, it stands out as an excellent choice for young athletes committed to excelling in their chosen sports.
Top Page Image Contents