Invacare Top End Terminator Jr Adjusting Seat Width Figure, Adjusting Front SEAT-TO-FLOOR Height

Page 25

SEAT

PROCEDURE 6

ADJUSTING SEAT WIDTH (FIGURE 4)

WARNING

The following procedure should only be per- formed by a qualified technician.

1.Remove the EXISTING footplate from the wheel- chair. Refer to PROCEDURE 8 of this manual.

2.Remove the EXISTING back upholstery from the wheelchair. Refer to PROCEDURE 4 of this manual.

3.Remove the EXISTING spreader bar from the wheelchair. Refer to REPLACING THE SPREADER BAR in PROCEDURE 4 of this manual.

4.Remove the EXISTING seat pan from the wheel- chair. Refer to REPLACING SEAT PAN in this pro- cedure of the manual.

NOTE: Retain the attachment hardware for installa- tion of the NEW seat pan.

5.Remove the axle tube from the wheelchair. Refer to REPLACING AXLE TUBE in PROCEDURE 7 of this manual.

6.Remove the four (4) hex screws and eight (8) coved washers that secure the two (2) EXISTING crossmembers to the wheelchair frame.

7.Remove the four (4) frame clamps from the EX- ISTING two (2) crossmembers.

8.Install the four (4) frame clamps onto the NEW (2) crossmembers.

9.Secure the two (2) NEW crossmembers to the front and rear mounting holes in the wheelchair frame with the hex screws and coved washers removed in STEP 5.

10.Install the NEW axle tube. Refer to REPLACING AXLE TUBE in PROCEDURE 7 of this manual.

11.Install the NEW seat pan using the EXISTING hardware. Refer to REPLACING SEAT PAN in this procedure of the manual.

12.Install the NEW back upholstery onto the wheel- chair. Refer to PROCEDURE 4 of this manual.

13.Install the NEW spreader bar onto the wheelchair. Refer to REPLACING THE SPREADER BAR in PROCEDURE 4 of this manual.

14.Install the NEW footplate onto the wheelchair. Re- fer to PROCEDURE 8 of this manual.

Hex Screws

 

Coved

Crossmember

Washers

 

 

Rear

 

Mounting

 

Hole

Crossmember

Wheelchair

 

 

Frame

 

Front Mounting Hole

FIGURE 4 - ADJUSTING SEAT WIDTH

ADJUSTING FRONT

SEAT-TO-FLOOR HEIGHT

WARNING

The position of the footrest, seat angle, back angle, seating system/upholstery, caster size and position, rear wheel size and position, anti-tippers, as well as the user condition directly relate to the stability of the wheelchair. Any change to one

(1)or any combination of the ten (10) may cause the wheelchair to decrease in stability. EXTREME care MUST be taken when changing the stability of the wheelchair. Refer tothe chart in STABILITY in PROCEDURE 1 of this manual.

Determining Frame Height (FIGURE 5)

Terminator Jr. Frames come in Short and Tall.

1.To determine frame height, measure from the bot- tom of the caster headtube to the top of the seat rail.

2.Refer to the chart to determine the frame size.

HEIGHT (INCHES)

FRAME SIZE

7-3/4

SHORT

10-1/2

TALL

Seat Rail

HEIGHT

(INCHES)Bottom of

Caster

Headtube

S E A T

FIGURE 5 - DETERMINING FRAME HEIGHT

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Terminator Junior JR Special Notes Table of Contents Specifications General Guidelines Procedure SAFETY/HANDLING WheelchairsStability and Balance Percentage of Weight DistributionCoping with Everyday Obstacles Reaching, Leaning and Bending Forward Functional Reach From a WheelchairReaching, Leaning Backwards TiltingTransferring to and From Other Seats StairwaysInitially Inspect Adjust Weekly Monthly Periodically Safety Inspection ChecklistMaintenance TroubleshootingMaintenance Safety Precautions Suggested Maintenance ProceduresChanging the Back Angle Figure FOLDING/UNFOLDING the Back FigureFolding the Back Unfolding the BackBack Replacing Adjustable Tension Back Upholstery Adjustable Tension StrapsBack Upholstery Cover Slide the back canes out of the back uprightsReplacing the Spreader BAR Figure Back in this procedure of the manualReplacing the Locking Mechanism in the Back Cane Figure CaneInstalling the Stroller Handles Installing the Stroller Handles FigureINSTALLING/REMOVING Cantilever Arms Figure Using Cantilever Arms FigureInstalling RemovingAdjusting Cantilever ARM Angle Figures 2 Adjusting Cantilever ARM Height FigureArmrest Pad Adjustment Armrest PAD ADJUSTMENT/ Replacement FigureArmrest Pad Replacement INSTALLING/REMOVING T-ARMS Figure Installing T-ARM Sockets FigureAdjusting the T-ARMS Adjusting T-Arm Width Figure Adjusting T-Arm Depth FigureAdjusting T-Arm Sockets Figure Replacing the T-ARM Locking Lever Figure Adjusting T-ARM SocketsAdjusting Seat Depth Figures 2 Adjusting Rear Seat Height FigureReplacing Seat PAN Figure PerformSTEPS1-2 ofREPLACINGTHESEATPANA T Adjusting Front SEAT-TO-FLOOR Height Adjusting Seat Width FigureDetermining Frame Height Figure Ensure wheel locks engage properly. Refer to Front Seat-to-floor Height AdjustmentAdjusting QUICK-RELEASE Axles Figure REMOVING/INSTALLING Rear Wheels FigureInstalling QUAD-RELEASE Axles Figure Adjusting QUAD-RELEASE Handles FigureHandrim Replacement Figure Removing Play From Rear WheelsOPENING/CLOSING Clamps Figure REPAIRING/REPLACING Rear WHEEL, TIRE/TUBECamber Clamps Receiver Tube ClampsClosed Position Adjusting Rear Wheel Camber FigureAdjusting Toe In/Toe Out Figure DETERMINING/ADJUSTING TOE IN/TOE OUTDetermining Toe In/Toe Out Figures 8 ING TOE IN/TOE OUT inthisprocedureofthemanual Adjusting Wheelbase Length FigureReplacing Axle Tube Figure Adjusting Wheelbase Width FigureRepositioning the Axle Tube Figures 14 E E L S REPOSITIONING/REPLACING Front Casters Figure Adjusting Front Caster Height FigureReplacing Front Casters Repositioning Front CastersRepeat this procedure for the opposite wheel lock Wheel Lock ADJUSTMENT/ Replacement FigureRepeat Steps 2-5 on the opposite front caster Engage the wheel lockAdjusting Flip-Up Footboard ADJUSTING/REPLACING FLIP-UP Footboard FigureReplacing Flip-Up Footboard ANTI-TIPPER REPLACEMENT/ Adjustment Figure ADJUSTING/REPLACING RigidTubular Footrest Figure Replacing Front Elastomers Figure Elastomers and SuspensionPage Page Limited Warranty One Invacare Way Chedworth Way

Top End Terminator Jr specifications

The Invacare Top End Terminator Jr is a premier wheelchair designed specifically for young athletes, providing both performance and versatility. It caters to the needs of competitive youth athletes, ensuring superior functionality and comfort during sports activities. The Terminator Jr blends advanced technology with thoughtful design, allowing young users to experience the thrill of competitive racing.

One of the standout features of the Terminator Jr is its lightweight aluminum frame. This construction not only enhances portability but also ensures that the wheelchair is robust enough to withstand the rigors of competitive sports. The frame is designed to provide optimal rigidity and stability, which translates into improved performance during races.

The Terminator Jr boasts an adjustable camber. This feature allows users to modify the angle of the wheels for increased speed and maneuverability. By altering the camber, athletes can optimize their performance based on personal preference and training requirements, making it an adaptable choice for different racing conditions and environments.

Another significant aspect of the Terminator Jr is its high-quality wheels and tires. The wheelchair is equipped with specialized racing wheels that offer excellent traction and control on various surfaces. The tires are designed for speed while ensuring stability, contributing to a superior racing experience.

The seat and backrests of the Terminator Jr are designed with comfort and support in mind. The seating system is adjustable, allowing for customization according to the athlete’s size and needs. This level of personalization helps to prevent discomfort during long periods of use, enabling young athletes to focus entirely on their performance.

Additionally, the Terminator Jr includes a variety of accessory options, such as footrests and backrest supports, which can be tailored to the athlete's preferences. This adaptability is key in ensuring that the wheelchair meets the specific requirements of different sports and individual users.

Safety and durability are paramount in the design of the Invacare Top End Terminator Jr. Its superior construction ensures that it can handle the physical demands of competitive racing, providing athletes with peace of mind as they focus on their performance.

In summary, the Invacare Top End Terminator Jr is a cutting-edge racing wheelchair that emphasizes performance, comfort, and customization. With its lightweight aluminum frame, adjustable camber, high-quality wheels, and customizable seating, it stands out as an excellent choice for young athletes committed to excelling in their chosen sports.
Top Page Image Contents