Invacare Top End Terminator Jr manual Replacing the Spreader BAR Figure, Cane

Page 15

BACK

PROCEDURE 4

REPLACING THE SPREADER BAR (FIGURE 6)

NOTE: Make sure the spreader bar is ALWAYS at- tached to the wheelchair.

1.Remove the back height adjustment screws that secure the back canes to the back uprights.

2.Remove the cantilever arms, if necessary. Refer to INSTALLING/REMOVING CANTILEVER ARMS in PROCEDURE 5 of this manual.

3.Loosen, but do not remove the two (2) set screws that secure the EXISTING spreader bar to the back canes.

4.Slide the EXISTING spreader bar off of the two

(2) back canes.

5.Slide the NEW spreader bar onto the back canes.

6.Securely tighten the two (2) set screws that se- cure the NEW spreader bar to the back canes.

7.Reinstall the cantilever arms, if necessary. Refer to INSTALLING/REMOVING CANTILEVER ARMS in PROCEDURE 5 of this manual.

8.Align the mounting hole in each back cane with the desired mounting hole in each back upright.

9.Install the two (2) back height adjustment screws through the back upright mounting holes deter- mined in STEP 8 and the back cane mounting holes.

REPLACING THE LOCKING MECHANISM IN THE BACK CANE (FIGURE 7)

WARNING

The locking mechanism is spring loaded. Place your free hand over the end of the back cane to prevent the locking mechansim from spring- ing out of the back cane.

1.Fold the back down. Refer to FOLDING/UNFOLD- ING BACK in this procedure of the manual.

2.Unscrew the actuator from the locking mechanism.

3.Remove the locking mechanism and spring from the back cane.

NOTE: Inspect the spring and replace if necessary.

4.Slide the NEW spring and locking mechanism into the back cane.

5.Make sure the angled end of the locking mecha- nism is at the bottom of the back cane.

NOTE: The long side of the locking mechanism should be toward the actuator opening.

6.

Push and hold the locking mechanism into the back

 

cane.

7.

Screw the actuator through the actuator opening

 

and into the locking mechanism mounting hole.

8.

Unfold the back. Refer to FOLDING/UNFOLDING

 

BACK in this procedure of the manual.

B A C K

Set

Screw

Back

Height

Adjustment

Screw

Back

Uprights

Mounting

Hole

Back Cane

Spreader

Bar

 

Back Cane

 

Actuator Opening

 

Actuator

Spring

Mounting

 

Locking

Hole

Long Side of

Mechanism

Locking Mechanism

 

FIGURE 6 - REPLACING THE SPREADER BAR

Angled End of the Locking Mechanism

FIGURE 7 - REPLACING THE LOCKING MECHANISM

IN THE BACK CANE

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Terminator Junior JR Special Notes Table of Contents Specifications General Guidelines Procedure SAFETY/HANDLING WheelchairsPercentage of Weight Distribution Stability and BalanceCoping with Everyday Obstacles Tilting Functional Reach From a WheelchairReaching, Leaning and Bending Forward Reaching, Leaning BackwardsTransferring to and From Other Seats StairwaysInitially Inspect Adjust Weekly Monthly Periodically Safety Inspection ChecklistSuggested Maintenance Procedures TroubleshootingMaintenance Maintenance Safety PrecautionsUnfolding the Back FOLDING/UNFOLDING the Back FigureChanging the Back Angle Figure Folding the BackBack Slide the back canes out of the back uprights Adjustable Tension StrapsReplacing Adjustable Tension Back Upholstery Back Upholstery CoverCane Back in this procedure of the manualReplacing the Spreader BAR Figure Replacing the Locking Mechanism in the Back Cane FigureInstalling the Stroller Handles Installing the Stroller Handles FigureRemoving Using Cantilever Arms FigureINSTALLING/REMOVING Cantilever Arms Figure InstallingAdjusting Cantilever ARM Angle Figures 2 Adjusting Cantilever ARM Height FigureArmrest PAD ADJUSTMENT/ Replacement Figure Armrest Pad AdjustmentArmrest Pad Replacement Installing T-ARM Sockets Figure INSTALLING/REMOVING T-ARMS FigureAdjusting the T-ARMS Adjusting T-Arm Depth Figure Adjusting T-Arm Width FigureAdjusting T-Arm Sockets Figure Replacing the T-ARM Locking Lever Figure Adjusting T-ARM SocketsPerformSTEPS1-2 ofREPLACINGTHESEATPAN Adjusting Rear Seat Height FigureAdjusting Seat Depth Figures 2 Replacing Seat PAN FigureA T Adjusting Seat Width Figure Adjusting Front SEAT-TO-FLOOR HeightDetermining Frame Height Figure Ensure wheel locks engage properly. Refer to Front Seat-to-floor Height AdjustmentAdjusting QUICK-RELEASE Axles Figure REMOVING/INSTALLING Rear Wheels FigureRemoving Play From Rear Wheels Adjusting QUAD-RELEASE Handles FigureInstalling QUAD-RELEASE Axles Figure Handrim Replacement FigureReceiver Tube Clamps REPAIRING/REPLACING Rear WHEEL, TIRE/TUBEOPENING/CLOSING Clamps Figure Camber ClampsClosed Position Adjusting Rear Wheel Camber FigureDETERMINING/ADJUSTING TOE IN/TOE OUT Adjusting Toe In/Toe Out FigureDetermining Toe In/Toe Out Figures 8 ING TOE IN/TOE OUT inthisprocedureofthemanual Adjusting Wheelbase Length FigureReplacing Axle Tube Figure Adjusting Wheelbase Width FigureRepositioning the Axle Tube Figures 14 E E L S Repositioning Front Casters Adjusting Front Caster Height FigureREPOSITIONING/REPLACING Front Casters Figure Replacing Front CastersEngage the wheel lock Wheel Lock ADJUSTMENT/ Replacement FigureRepeat this procedure for the opposite wheel lock Repeat Steps 2-5 on the opposite front casterADJUSTING/REPLACING FLIP-UP Footboard Figure Adjusting Flip-Up FootboardReplacing Flip-Up Footboard ADJUSTING/REPLACING Rigid ANTI-TIPPER REPLACEMENT/ Adjustment FigureTubular Footrest Figure Replacing Front Elastomers Figure Elastomers and SuspensionPage Page Limited Warranty One Invacare Way Chedworth Way

Top End Terminator Jr specifications

The Invacare Top End Terminator Jr is a premier wheelchair designed specifically for young athletes, providing both performance and versatility. It caters to the needs of competitive youth athletes, ensuring superior functionality and comfort during sports activities. The Terminator Jr blends advanced technology with thoughtful design, allowing young users to experience the thrill of competitive racing.

One of the standout features of the Terminator Jr is its lightweight aluminum frame. This construction not only enhances portability but also ensures that the wheelchair is robust enough to withstand the rigors of competitive sports. The frame is designed to provide optimal rigidity and stability, which translates into improved performance during races.

The Terminator Jr boasts an adjustable camber. This feature allows users to modify the angle of the wheels for increased speed and maneuverability. By altering the camber, athletes can optimize their performance based on personal preference and training requirements, making it an adaptable choice for different racing conditions and environments.

Another significant aspect of the Terminator Jr is its high-quality wheels and tires. The wheelchair is equipped with specialized racing wheels that offer excellent traction and control on various surfaces. The tires are designed for speed while ensuring stability, contributing to a superior racing experience.

The seat and backrests of the Terminator Jr are designed with comfort and support in mind. The seating system is adjustable, allowing for customization according to the athlete’s size and needs. This level of personalization helps to prevent discomfort during long periods of use, enabling young athletes to focus entirely on their performance.

Additionally, the Terminator Jr includes a variety of accessory options, such as footrests and backrest supports, which can be tailored to the athlete's preferences. This adaptability is key in ensuring that the wheelchair meets the specific requirements of different sports and individual users.

Safety and durability are paramount in the design of the Invacare Top End Terminator Jr. Its superior construction ensures that it can handle the physical demands of competitive racing, providing athletes with peace of mind as they focus on their performance.

In summary, the Invacare Top End Terminator Jr is a cutting-edge racing wheelchair that emphasizes performance, comfort, and customization. With its lightweight aluminum frame, adjustable camber, high-quality wheels, and customizable seating, it stands out as an excellent choice for young athletes committed to excelling in their chosen sports.
Top Page Image Contents