Invacare Top End Terminator Jr manual Adjusting T-Arm Depth Figure, Adjusting T-Arm Width Figure

Page 21

ARMS

PROCEDURE 5

2.Slide the T-arm to one (1) of:

A.Low Height T-Arms- Nine (9) positions.

B.High Height T-Arms- Seven (7) positions.

NOTE: If the inside T-arm post does not slide up and down in the outside T-arm post as desired, perform one (1) of the following:

A.Tighten - Tightening the set screws on the out- side T-arm post will make it harder to move the inside T-arm post up and down.

B.Loosen - Loosening the set screws on the out- side T-arm post will make it easier to move the inside T-arm post up and down.

3.Lock the T-arm by flipping the T-arm release le- ver towards the front of the wheelchair.

Inside T-Arm

Adjusting T-Arm Depth (FIGURE 10)

1.Remove the two (2) phillips screws that secure the arm pad to the arm tube.

2.Remove the two (2) socket screws that secure the arm tube to the T-arm post.

3.Reposition the arm tube on the T-arm post:

A.Desk Length Arms - to one (1) of three (3) posi- tions depending on the desired arm pad depth.

B.Full Length Arms - to one (1) of five (5) posi- tions depending on the desired arm pad depth.

NOTE: Additional positions are obtainable by turning the arm tube 180o.

4.Re-secure the arm tube to the T-arm post with the two (2) socket screws. Torque to 60-70 in./lbs.

5.Reattach the arm pad to the arm tube with the two (2) phillips screws. Tighten securely.

6.Repeat for the opposite side, if necessary.

A R M S

Set

Screws

Outside

Post

T-Arm Release Lever -

Socket

Arm Pad

Arm Tube NOTE: If

T- Arm Post

Unlocked Position

T-Arm Release Lever - Locked Position

FIGURE 8 - ADJUSTING T-ARM HEIGHT

Adjusting T-Arm Width (FIGURE 9)

1. Remove the two (2) phillips screws that secure the

Screws

Phillips

Screw

T-Arm Post

necessary, turn arm tube 180o to obtain two

(2)positions.

Phillips Screw

 

arm pad to the arm tube.

2.

Turn the arm pad around and reposition the arm pad

 

on the arm tube.

3.

Re-secure the arm pad to the arm tube with the two

 

(2) phillips screws. Tighten securely.

4.

Repeat for the opposite side, if necessary.

Arm Pad

Arm Tube

Phillips

Phillips Screw

Screw

 

FIGURE 9 - ADJUSTING T-ARM WIDTH

FIGURE 10 - ADJUSTING T-ARM DEPTH

Adjusting T-Arm Sockets (FIGURE 11)

NOTE: Perform this procedure if the T-arm is too loose in the socket or does not easily slide up and down in the socket.

1.Remove the rear wheels from the wheelchair, if nec- essary. Refer to REMOVING/INSTALLING REAR WHEELS in PROCEDURE 7 of this manual.

2.Loosen, but do not remove the four (4) hex screws andwashersthatsecureT-armsockettoT-armclamp.

NOTE: The T-arm socket will disassemble if the four

(4) hex screws and washers are removed.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Terminator Junior JR Special Notes Table of Contents Specifications General Guidelines Procedure SAFETY/HANDLING WheelchairsPercentage of Weight Distribution Stability and BalanceCoping with Everyday Obstacles Reaching, Leaning and Bending Forward Functional Reach From a WheelchairReaching, Leaning Backwards TiltingTransferring to and From Other Seats StairwaysInitially Inspect Adjust Weekly Monthly Periodically Safety Inspection ChecklistMaintenance TroubleshootingMaintenance Safety Precautions Suggested Maintenance ProceduresChanging the Back Angle Figure FOLDING/UNFOLDING the Back FigureFolding the Back Unfolding the BackBack Replacing Adjustable Tension Back Upholstery Adjustable Tension StrapsBack Upholstery Cover Slide the back canes out of the back uprightsReplacing the Spreader BAR Figure Back in this procedure of the manualReplacing the Locking Mechanism in the Back Cane Figure CaneInstalling the Stroller Handles Installing the Stroller Handles FigureINSTALLING/REMOVING Cantilever Arms Figure Using Cantilever Arms FigureInstalling RemovingAdjusting Cantilever ARM Angle Figures 2 Adjusting Cantilever ARM Height FigureArmrest PAD ADJUSTMENT/ Replacement Figure Armrest Pad AdjustmentArmrest Pad Replacement Installing T-ARM Sockets Figure INSTALLING/REMOVING T-ARMS FigureAdjusting the T-ARMS Adjusting T-Arm Depth Figure Adjusting T-Arm Width FigureAdjusting T-Arm Sockets Figure Replacing the T-ARM Locking Lever Figure Adjusting T-ARM SocketsAdjusting Seat Depth Figures 2 Adjusting Rear Seat Height FigureReplacing Seat PAN Figure PerformSTEPS1-2 ofREPLACINGTHESEATPANA T Adjusting Seat Width Figure Adjusting Front SEAT-TO-FLOOR HeightDetermining Frame Height Figure Ensure wheel locks engage properly. Refer to Front Seat-to-floor Height AdjustmentAdjusting QUICK-RELEASE Axles Figure REMOVING/INSTALLING Rear Wheels FigureInstalling QUAD-RELEASE Axles Figure Adjusting QUAD-RELEASE Handles FigureHandrim Replacement Figure Removing Play From Rear WheelsOPENING/CLOSING Clamps Figure REPAIRING/REPLACING Rear WHEEL, TIRE/TUBECamber Clamps Receiver Tube ClampsClosed Position Adjusting Rear Wheel Camber FigureDETERMINING/ADJUSTING TOE IN/TOE OUT Adjusting Toe In/Toe Out FigureDetermining Toe In/Toe Out Figures 8 ING TOE IN/TOE OUT inthisprocedureofthemanual Adjusting Wheelbase Length FigureReplacing Axle Tube Figure Adjusting Wheelbase Width FigureRepositioning the Axle Tube Figures 14 E E L S REPOSITIONING/REPLACING Front Casters Figure Adjusting Front Caster Height FigureReplacing Front Casters Repositioning Front CastersRepeat this procedure for the opposite wheel lock Wheel Lock ADJUSTMENT/ Replacement FigureRepeat Steps 2-5 on the opposite front caster Engage the wheel lockADJUSTING/REPLACING FLIP-UP Footboard Figure Adjusting Flip-Up FootboardReplacing Flip-Up Footboard ADJUSTING/REPLACING Rigid ANTI-TIPPER REPLACEMENT/ Adjustment FigureTubular Footrest Figure Replacing Front Elastomers Figure Elastomers and SuspensionPage Page Limited Warranty One Invacare Way Chedworth Way

Top End Terminator Jr specifications

The Invacare Top End Terminator Jr is a premier wheelchair designed specifically for young athletes, providing both performance and versatility. It caters to the needs of competitive youth athletes, ensuring superior functionality and comfort during sports activities. The Terminator Jr blends advanced technology with thoughtful design, allowing young users to experience the thrill of competitive racing.

One of the standout features of the Terminator Jr is its lightweight aluminum frame. This construction not only enhances portability but also ensures that the wheelchair is robust enough to withstand the rigors of competitive sports. The frame is designed to provide optimal rigidity and stability, which translates into improved performance during races.

The Terminator Jr boasts an adjustable camber. This feature allows users to modify the angle of the wheels for increased speed and maneuverability. By altering the camber, athletes can optimize their performance based on personal preference and training requirements, making it an adaptable choice for different racing conditions and environments.

Another significant aspect of the Terminator Jr is its high-quality wheels and tires. The wheelchair is equipped with specialized racing wheels that offer excellent traction and control on various surfaces. The tires are designed for speed while ensuring stability, contributing to a superior racing experience.

The seat and backrests of the Terminator Jr are designed with comfort and support in mind. The seating system is adjustable, allowing for customization according to the athlete’s size and needs. This level of personalization helps to prevent discomfort during long periods of use, enabling young athletes to focus entirely on their performance.

Additionally, the Terminator Jr includes a variety of accessory options, such as footrests and backrest supports, which can be tailored to the athlete's preferences. This adaptability is key in ensuring that the wheelchair meets the specific requirements of different sports and individual users.

Safety and durability are paramount in the design of the Invacare Top End Terminator Jr. Its superior construction ensures that it can handle the physical demands of competitive racing, providing athletes with peace of mind as they focus on their performance.

In summary, the Invacare Top End Terminator Jr is a cutting-edge racing wheelchair that emphasizes performance, comfort, and customization. With its lightweight aluminum frame, adjustable camber, high-quality wheels, and customizable seating, it stands out as an excellent choice for young athletes committed to excelling in their chosen sports.
Top Page Image Contents