Invacare Top End Terminator Jr Replacing the T-ARM Locking Lever Figure, Adjusting T-ARM Sockets

Page 22

PROCEDURE 5

ARMS

A R M S

3.Slide the T-arm into the T-arm socket until the locking lever is in the slot in the T-arm socket and an audible "click" is heard.

4.Squeeze the T-arm socket the T-arm clamp together until the socket is flush with the T-arm.

5.While holding the T-arm socket and the T-arm clamp together, tighten the four (4) hex screws and washers. Tighten securely.

6.Press in on the locking lever and lift the T-arm straight up and out of the T-arm socket.

7.Repeat STEPS 3-6, if necessary until the T-arm slides in the T-arm socket as desired.

8.If necessary, install rear wheels. Refer to REMOV- ING/INSTALLING REAR WHEELSin PROCEDURE 7 of this manual.

WARNING

The locking lever is spring loaded. Place your free hand over the locking lever to prevent the parts from springing off of the bottom bracket, other- wise parts may be lost or injury may occur.

3.Remove EXISTING locking lever and spring from bottom bracket.

NOTE: Inspect the spring and replace if necessary.

4.Position spring on bottom bracket as shown in FIG- URE 12.

5.Position NEW locking lever onto spring and bottom bracket (DETAIL "A").

NOTE: Make sure the two (2) extended ends of the spring are inside the notch in the locking lever.

6.Line up the mounting holes in the NEW locking lever, spring and bottom bracket.

T-Arm

T-Arm Clamp

Hex Screws

and WashersHex Screws

and Washers

Slot

Locking Lever

T-Arm Socket

 

FIGURE 11 - ADJUSTING T-ARM SOCKETS

WARNING

DO NOT over tighten locknut that secures lockingle- vertobottombracket.Overtighteningthislocknutwill preventlockingleverfromoperatingproperly,possibly causing injury.

7.Install phillips bolt and tighten securely with locknut.

8.Install the T-arm onto the wheelchair. Refer to IN- STALLING/REMOVING T-ARMS in this procedure of the manual.

DETAIL "A" - MOUNTING THE SPRING

 

Mounted

Extended Ends

Spring

Spring

REPLACING THE T-ARM LOCKING LEVER (FIGURE 12)

1.Remove T-arm from wheelchair. Refer to IN- STALLING/REMOVING T-ARMS in this proce- dure of the manual.

2.Remove the phillips bolt and locknut that secure the EXISTING locking lever to the bottom bracket.

Notch

Locknut

Bottom

Bracket

Phillips Bolt

Locking

Lever

 

FIGURE 12 - REPLACING THE T-ARM LOCKING LEVER

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Terminator Junior JR Special Notes Table of Contents Specifications General Guidelines SAFETY/HANDLING Wheelchairs ProcedureStability and Balance Percentage of Weight DistributionCoping with Everyday Obstacles Reaching, Leaning Backwards Functional Reach From a WheelchairReaching, Leaning and Bending Forward TiltingStairways Transferring to and From Other SeatsSafety Inspection Checklist Initially Inspect Adjust Weekly Monthly PeriodicallyMaintenance Safety Precautions TroubleshootingMaintenance Suggested Maintenance ProceduresFolding the Back FOLDING/UNFOLDING the Back FigureChanging the Back Angle Figure Unfolding the BackBack Back Upholstery Cover Adjustable Tension StrapsReplacing Adjustable Tension Back Upholstery Slide the back canes out of the back uprightsReplacing the Locking Mechanism in the Back Cane Figure Back in this procedure of the manualReplacing the Spreader BAR Figure CaneInstalling the Stroller Handles Figure Installing the Stroller HandlesInstalling Using Cantilever Arms FigureINSTALLING/REMOVING Cantilever Arms Figure RemovingAdjusting Cantilever ARM Height Figure Adjusting Cantilever ARM Angle Figures 2Armrest Pad Adjustment Armrest PAD ADJUSTMENT/ Replacement FigureArmrest Pad Replacement INSTALLING/REMOVING T-ARMS Figure Installing T-ARM Sockets FigureAdjusting the T-ARMS Adjusting T-Arm Width Figure Adjusting T-Arm Depth FigureAdjusting T-Arm Sockets Figure Adjusting T-ARM Sockets Replacing the T-ARM Locking Lever FigureReplacing Seat PAN Figure Adjusting Rear Seat Height FigureAdjusting Seat Depth Figures 2 PerformSTEPS1-2 ofREPLACINGTHESEATPANA T Adjusting Front SEAT-TO-FLOOR Height Adjusting Seat Width FigureDetermining Frame Height Figure Front Seat-to-floor Height Adjustment Ensure wheel locks engage properly. Refer toREMOVING/INSTALLING Rear Wheels Figure Adjusting QUICK-RELEASE Axles FigureHandrim Replacement Figure Adjusting QUAD-RELEASE Handles FigureInstalling QUAD-RELEASE Axles Figure Removing Play From Rear WheelsCamber Clamps REPAIRING/REPLACING Rear WHEEL, TIRE/TUBEOPENING/CLOSING Clamps Figure Receiver Tube ClampsAdjusting Rear Wheel Camber Figure Closed PositionAdjusting Toe In/Toe Out Figure DETERMINING/ADJUSTING TOE IN/TOE OUTDetermining Toe In/Toe Out Figures 8 Adjusting Wheelbase Length Figure ING TOE IN/TOE OUT inthisprocedureofthemanualAdjusting Wheelbase Width Figure Replacing Axle Tube FigureRepositioning the Axle Tube Figures 14 E E L S Replacing Front Casters Adjusting Front Caster Height FigureREPOSITIONING/REPLACING Front Casters Figure Repositioning Front CastersRepeat Steps 2-5 on the opposite front caster Wheel Lock ADJUSTMENT/ Replacement FigureRepeat this procedure for the opposite wheel lock Engage the wheel lockAdjusting Flip-Up Footboard ADJUSTING/REPLACING FLIP-UP Footboard FigureReplacing Flip-Up Footboard ANTI-TIPPER REPLACEMENT/ Adjustment Figure ADJUSTING/REPLACING RigidTubular Footrest Figure Elastomers and Suspension Replacing Front Elastomers FigurePage Page Limited Warranty One Invacare Way Chedworth Way

Top End Terminator Jr specifications

The Invacare Top End Terminator Jr is a premier wheelchair designed specifically for young athletes, providing both performance and versatility. It caters to the needs of competitive youth athletes, ensuring superior functionality and comfort during sports activities. The Terminator Jr blends advanced technology with thoughtful design, allowing young users to experience the thrill of competitive racing.

One of the standout features of the Terminator Jr is its lightweight aluminum frame. This construction not only enhances portability but also ensures that the wheelchair is robust enough to withstand the rigors of competitive sports. The frame is designed to provide optimal rigidity and stability, which translates into improved performance during races.

The Terminator Jr boasts an adjustable camber. This feature allows users to modify the angle of the wheels for increased speed and maneuverability. By altering the camber, athletes can optimize their performance based on personal preference and training requirements, making it an adaptable choice for different racing conditions and environments.

Another significant aspect of the Terminator Jr is its high-quality wheels and tires. The wheelchair is equipped with specialized racing wheels that offer excellent traction and control on various surfaces. The tires are designed for speed while ensuring stability, contributing to a superior racing experience.

The seat and backrests of the Terminator Jr are designed with comfort and support in mind. The seating system is adjustable, allowing for customization according to the athlete’s size and needs. This level of personalization helps to prevent discomfort during long periods of use, enabling young athletes to focus entirely on their performance.

Additionally, the Terminator Jr includes a variety of accessory options, such as footrests and backrest supports, which can be tailored to the athlete's preferences. This adaptability is key in ensuring that the wheelchair meets the specific requirements of different sports and individual users.

Safety and durability are paramount in the design of the Invacare Top End Terminator Jr. Its superior construction ensures that it can handle the physical demands of competitive racing, providing athletes with peace of mind as they focus on their performance.

In summary, the Invacare Top End Terminator Jr is a cutting-edge racing wheelchair that emphasizes performance, comfort, and customization. With its lightweight aluminum frame, adjustable camber, high-quality wheels, and customizable seating, it stands out as an excellent choice for young athletes committed to excelling in their chosen sports.
Top Page Image Contents