Friedrich MW18C3F, MR18C3F operation manual Cleaning and Care, En-11

Page 12

CLEANING AND CARE

CAUTION!

●Before cleaning the air conditioner, be sure to turn it off and disconnect the Power.

● Be sure the Intake Grille (Fig. 1 9) is installed securely.

● When removing and replacing the air filters, be sure not to touch the heat exchanger, as per- sonal injury may result.

Cleaning the Intake Grille

1.Remove the Intake Grille.

1 Place your fingers at both lower ends of the grille panel, and lift forward; if the grille seems to catch partway through its movement, continue lifting up- ward to remove.

2Pull past the intermediate catch and open the Intake Grille wide so that it become horizontal.

Intake Grille

Intake Grille

Mounting

shaft

Knob

Cleaning the Air Filter

1. Open the Intake Grille, and remove the air filter.

Lift up the air filter’s handle, disconnect the two lower tabs, and pull out.

Air filter handle

Hooks (two places)

2. Remove dust with a vacuum cleaner or by washing.

After washing, allow to dry thoroughly in a shaded place.

3.Replace the Air Filter and close the Intake Grille.

1 Align the sides of the air filter with the panel, and push in fully, making sure the two lower tabs are returned properly to their holes in the panel.

2. Clean with water.

Remove dust with a vacuum cleaner; wipe the unit with warm water, then dry with a clean, soft cloth.

3. Replace the Intake Grille.

1Pull the knobs all the way.

2Hold the grille horizontal and set the left and right mounting shafts into the bearings at the top of the panel.

3Press the place where the arrow on the diagram indi- cates and close the Intake Grille.

Hooks (two places)

2Close the Intake Grille.

(For purposes of example, the illustration shows the unit without Intake Grille installed.)

● Dust can be cleaned from the air filter either with a vacuum

cleaner, or by washing the filter in a solution of mild de-

tergent and warm water. If you wash the filter, be sure to

Intake

Grille

Intake Grille

Mounting

shaft

2

1

Mounting shaft Bearing

Knob

allow it to dry thoroughly in a shady place before rein-

stalling.

● If dirt is allowed to accumulate on the air filter, air flow

will be reduced, lowering operating efficiency and increas-

ing noise.

● During periods of normal use, the Air Filters should be

cleaned every two weeks.

Knob

●When used for extended periods, the unit may accumulate dirt inside, reducing its performance. We recommend that the unit be inspected regularly, in addition to your own cleaning and care. For more information, consult authorized service personnel.

●When cleaning the unit’s body, do not use water hotter than 104 °F, harsh abrasive cleansers, or volatile agents like benzene or thinner.

●Do not expose the unit body to liquid insecticides or hairsprays.

●When shutting down the unit for one month or more, first allow the fan mode to operate continuously for about one-half day to allow internal parts to dry thoroughly.

En-11

06B030_9315255044-01_En

11

2006.2.9, 9:55 AM

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Operating Manual Español Français EnglishContents Safety PrecautionsSpecifications Fiche TechniqueFeatures and Functions En-2Name of Parts En-3Preparation En-4Operation En-5About Mode Operation En-6To Stop Operation Press the START/STOP button Q About Auto Changeover OperationTimer Operation En-7Sleep Timer Operation About the Sleep TimerEn-8 During Cooling/Dry operationAdjusting the Direction of AIR Circulation Vertical Air Direction Adjustment Press the SET button RRight-Left Adjustment Adjust the Right-Left louvers Types of Air flow Direction SettingSwing Operation Manual Auto OperationEn-10 To select Swing Operation Press the Swing button SCleaning and Care En-11Install the Air cleaning filter set set Install the two Air filters and close the Intake GrilleReplacing dirty Air cleaning filters Replace them by two new Air cleaning filtersTroubleshooting Symptom ProblemEn-13 NormalEvent of Power Interruption Symptom Items to checkOperating Tips En-14Temperature and Humidity Range Cooling Mode Dry Mode Outdoor temperatureIndoor temperature About 64 F to 90 F En-1506B0309315255044-01En 2006.2.6, 147 PM Sommaire Précautions DE SécuritéFr-1 Caractéristiques ET Fonctions Fr-2Nomenclature DES Organes Fr-3Préparatifs Fr-4Fonctionnement Fr-5Réglage du thermostat Appuyez sur la touche SET TEMP. L Fonctionnement Super SilencieuxPropos du mode de fonctionnement Fr-6Arrêt du climatiseur Appuyez sur la touche START/STOP Q Fonctionnement PAR Minuterie DE Programmation Fr-7Propos de la programmation combinée Marche/Arrêt Fonctionnement Temporisé Fr-8Changement des réglages du minuterie Propos de la minuterie à temporisateurRéglage DE LA Direction DU Flux D’AIR Fr-9Réglage Gauche-Droite Ajustez les Volets Gauche-Droite Positions de réglage de direction du flux d’airFonctionnement Oscillant Fonctionnement MANUEL-AUTOMATIQUEFr-10 Propos du fonctionnement oscillantNettoyage ET Entretien Fr-11Nettoyez à l’eau Remettez la grille d’admissionRemplacement de filtres de nettoyage d’air sales Fr-12Remplacez-les par deux nouveaux filtres de nettoyage d’air Remarques sur les filtres de nettoyage d’airGuide DE Dépannage Fr-13Symptôme Problème Voyez FonctionsConseils D’UTILISATION Fr-14Remise en marche automatique En cas de coupure de courantFr-15 Plage de température et d’humiditéConseils pour une économie d’énergie Température intérieure Environ 64 F à 90 F06B0309315255044-01Fr 2006.2.6, 222 PM Índice Precauciones DE SeguridadSp-1 Características Y Funciones Sp-2Denominación DE LOS Componentes Sp-3Preparativos Sp-4Funcionamiento Sp-5Para seleccionar el modo de funcionamiento Para ajustar el termostatoSp-6 NotassobreelfuncionamientodecambioautomáticoAUTOCHANGEOVERNotas sobre el funcionamiento de los modos Funcionamiento CON Temporizador Sp-7Empleo del temporizador programable Si el aparato ya está funcionando pase al pasoSp-8 Para cambiar los ajustes del tiempoNotas sobre el temporizador de desconexión automática Sleep Durante el funcionamiento de refrigeración/deshumectaciónAjuste DE LA Dirección DE Circulación DEL Aire Sp-9Tipos de ajustes de la dirección del flujo de aire Funcionamiento DE Vaivén Funcionamiento Manual Y AutomáticoSp-10 Observaciones sobre el funcionamiento de vaivénLimpieza Y Mantenimiento Sp-11Sustitución de los filtros de limpieza de aire sucios Sustitúyalos dos filtros de limpieza de aire nuevosAcerca de los filtros de limpieza de aire Mantenimiento de los filtros desodorizantesSíntoma Problema Vea la Página Localización DE AveríasSp-13 FuncionesConsejos Para EL Funcionamiento Sp-14Reinicio automático En el caso de una interrupción de la alimentaciónSp-15 Margen de temperatura y humedadConsejos para el ahorro de energía Temperatura interior Aprox F a 90 F06B0309315255044-01Sp 2006.2.6, 222 PM 06B0309315255044-01Sp 2006.2.6, 222 PM

MR18C3F, MW18C3F specifications

The Friedrich MW18C3F and MR18C3F are two innovative air conditioning units designed to provide optimal comfort and efficiency in home and office environments. Both models are part of Friedrich's commitment to delivering high-quality climate control solutions that cater to various needs and preferences.

One of the standout features of the MW18C3F and MR18C3F is their advanced inverter technology. This technology enables the units to adjust their cooling capacity according to the ambient temperature, ensuring that energy consumption is minimized while still maintaining a comfortable environment. By operating at variable speeds, the inverter systems reduce energy waste, making these units eco-friendly options.

The MW18C3F is equipped with a cooling capacity of 18,000 BTU, making it suitable for medium to large spaces, while the MR18C3F model offers similar cooling performance with added versatility for different installation options. Both models boast a high EER (Energy Efficiency Ratio) rating, which indicates excellent energy efficiency, leading to lower utility bills while still being effective in combating heat.

Another significant characteristic of these models is their smart technology integration. The Friedrich MW18C3F and MR18C3F offer Wi-Fi connectivity, allowing users to control the system remotely via a smartphone app. This feature provides unparalleled convenience, enabling users to set schedules, adjust temperatures, and monitor energy consumption from virtually anywhere. The app also supports voice commands, compatible with major smart home platforms, enhancing user experience.

In terms of design, both units feature a sleek and modern aesthetic that blends well with most interior décors. They come with a user-friendly interface, simplifying operation and customization of settings. The units are also designed with noise reduction technologies, ensuring that they operate quietly, making them suitable for bedrooms and workspaces where tranquility is crucial.

The filtration system in the MW18C3F and MR18C3F is another important aspect, featuring washable filters that help maintain indoor air quality by trapping dust and allergens. This not only improves the comfort of users but also prolongs the lifespan of the units by preventing buildup of dirt and debris.

Overall, the Friedrich MW18C3F and MR18C3F showcase a combination of advanced technology, energy efficiency, and user-friendly features. With their modern design and smart capabilities, these air conditioners stand out as excellent choices for anyone looking to enhance their indoor climate control while being mindful of energy consumption.
Top Page Image Contents