Lincoln Electric IM10023 manual 200

Page 18

B-3	OPERATION	B-3

	FIGURE B.1 - INPUT AND OUTPUT CONNECTIONS

	STATUS
	LIGHT
	PENDANT
	CONNECTOR
	MAXsa™ 22 or 29
	WIRE DRIVE CONNECTOR (14-PIN)
	POWER WAVE® AC/DC 1000 SD
	ARCLINK CONNECTOR
			FLUX HOPPER
			CONNECTOR
			TC-3 TRAVEL CARRIAGE		ACCESS
			TC-3 TRAVEL CARRIAGE		HOLES
			CONNECTOR		HOLES
			CONNECTOR
		FIGURE B.2 - PENDANT CONTROLS
			AMPS/WFS	MODE SELECT		VOLTS
			DISPLAY	PANEL (MSP)		DISPLAY
		WFS	AMPS/WFS	DISPLAY		VOLTS
	AMPS	WFS	AMPS/WFS	VOLTS		VOLTS
	AMPS	INDICATOR	CONTROL	CONTROL		INDICATOR
	INDICATOR	INDICATOR	CONTROL	CONTROL		INDICATOR
	INDICATOR
	TRAVEL SWITCH					START
	TRAVEL SWITCH					BUTTON
	(AUTO / OFF / MANUAL)					BUTTON
	(AUTO / OFF / MANUAL)
	FLUX FILL		200	----		WELD OUTPUT
	SWITCH					INDICATOR
						INDICATOR

WELD MODE

SELECTOR

WELD MODE

INDICATOR

FREQUENCY AND BALANCE INDICATOR

MEMORY

BUTTONS (8)

MODE SELECT PANEL

CONTROL

4

Steel 1/8”

CC AC

STOP

BUTTON

SET-UP MENU

INDICATOR

ARC START/END

OPTIONS SELECTOR

START OPTIONS

INDICATOR

END OPTIONS

INDICATOR

FEED

REVERSE

FEED

FORWARD

MAXsa™ 10 CONTROLLER

Image 18

Contents Controller Safety Electric Shock can kill Welding and Cutting Sparks can Cause fire or explosion Précautions DE Sûreté Thank You Table of Contents Installation Technical Specifications MAXsa 10 ControllerSafety Precaution Figure A.1 MAXsa 10 Connections Interfacing to the MAXsa 10 CON TrollerFigure A.3 Figure A.4 Controlling NON-LINCOLN Equipment Shutdown Inputs Stop InputFigure A.6 Connection Diagram Single ARC System Operation Safety PrecautionsDesign Features Definitions of Welding ModesGeneral Functional Description Recommended Processes and EquipmentGeneral Physical Description Common Basic Equipment Packages200 POWER-UP Sequence Wire Feeder SetupSetting Feed FORWARD/REVERSE Balance Adjust Changing and Setting Weld ModesFrequency Adjust Offset AdjustMultiple ARC Configuration Weld Mode SearchingSearching for a Weld Mode Table B.1 Phase Relationship ARCStart Options Operation Arc Delay TimeWeld Sequence Start OptionsEND Options END Options OperationDownslope Time Parameter Definition Accessing the Setup MenuAccess Preference Change Preference SelectionUser Defined Parameters Parameter Definition Hot-Inch Touch Sense Option Wire Drive Gear Ratio100 View Diagnostics? Shutdown 2 Function Select102 View Fatal Logs 107 View Power Source ProtocolParameter Definition 101 View Event Logs 103 View Software Version Information505 Setup Menu Lock 503 Memory Button Disable504 Mode Select Panel Lock Parameter Definition 502 Memory Change LockoutTouch Sense Parameter Definition 506 Set User Interface Passcode509 UI Master Lockout Lockout / SecurityMaking a Weld Figure B.7 Making a WeldUsing the Memory Option Naming a Saved ProcedureMulti Procedure Welding Steel 1/8 Saving a Procedure to a Memory LocationRecalling a Procedure from a Memory Location CC DC +Optional Limit Setup Setting LimitsAccessories Follow these stepsMaintenance Routine MaintenancePeriodic Maintenance Calibration Specification Troubleshooting HOW to USE Troubleshooting GuideUsing the Status LED to Troubleshoot System Problems Table E.1Arclink System Error Codes Troubleshooting Verify correct sense lead connection Output Disabled Output Problems Troubleshooting Diagrams Enhanced DiagramDimension Print L13444Precaucion Warnung