Hitachi C 7YA instruction manual USE of Dust BAG, USE of Dust Guide, Mounting the dust bag

Page 18

English

USE OF DUST BAG

WARNING:

To avoid serious accident, ensure the switch is in the OFF position, and disconnect the plug from the receptacle.

Never attempt to saw any material like metal and so on that give off sparks. Such action can lead to fire or injury.

Adapting Mouth

Clasp

 

1.Mounting the dust bag

Hold the clasp of the dust bag and insert it into the adapting mouth of the body while opening the thrusting mouth. (Fig. 19)

2.Dumping sawdust and cleaning the inside of dust bag

NOTE: If too much sawdust is accumulated inside the dust bag, the dust collector will run low on power. Attempt to dump the sawdust as early as you can and clean the dust bag thoroughly so that you can enjoy your work with strong dust collecting power.

(1)Hold the clasp, open the thrusting mouth of the dust bag, and pull it off from the body.

(2)Open the fastener (Fig. 20) and dump the sawdust.

Dust Bag

Fig. 19

Fastener

Fig. 20

USE OF DUST GUIDE

WARNING:

To avoid serious accidents, ensure the switch is in the OFF position, and disconnect the plug from the receptacle.

The dust guide is a component part that changes the discharge direction of sawdust and is not a tool to collect dust. Make certain that you wear protective glasses and a dustproof mask during the use of the dust guide.

CAUTION:

The dust guide can change the direction of the discharge direction. Never point it in the direction of the worker.

Never carry the tool by the dust guide.

18

Image 18
Contents 7YA AvertissementContents Meanings of Signal Words Important InformationSafety Safety RulesDON’T Force Tool Remove Adjusting Keys and WrenchesKeep Children Away USE Right ToolOperate Power Tools AT the Rated Voltage Check for Live WiresKeep Motor AIR Vent Clean Carefully Handle Power ToolsEnglish Do not RUN the SAW While Carrying IT AT Your Side Service and Repairs USE of Extension Cord Make Them Available to Other Users of this Tool Double Insulation for Safer OperationSpecifications Functional DescriptionName of Parts Assembly and Operation ApplicationsPrior to Operation Adjustsing the SAW Prior to USE Adjusting the cutting depth Fig Adjusting the angle of inclinationRegulating the guide Rip fence Cutting Procedures Pocket CuttingMounting and Dismounting the SAW Blade Dismounting the saw blade FigMounting the saw blade USE of Dust Guide Dumping sawdust and cleaning the inside of dust bagUSE of Dust BAG Mounting the dust bagMounting the dust guide Maintenance and Inspection Service parts list ModificationsAccessories Standard AccessoriesInformations Importantes Signification DES Mots D’AVERTISSEMENTLire Tout CE Mode D’EMPLOI SecuriteRegles DE Securite Utiliser L’OUTIL Correct Eloigner LES EnfantsNE PAS Forcer L’OUTIL SE Vetir CorrectementVerifier S’IL Y a DES Fils Sous Tension Verifier S’IL Y a DES Pieces EndommageesManipuler L’OUTIL Correctement Garder Propres LES Events D’AIR DU MoteurManipuler L’OUTIL Motorise Avec Precaution NE PAS Essuyer LES Parties EN Plastique Avec DU SolvantNE PAS Transporter LA Scie a LA Main Avec LA Lame QUI Tourne NE PAS Essayer DE Tenir LES Sections Courtes À LA Main Service APRES-VENTE ET Reparations Pieces DE RechangeFiches Polarisees Utilisation D’UN Cordon DE Rallonge Calibre Minimum DES CordonsDouble Isolation Pour UN Fonctionnement Plus SUR Description Fonctionnelle NOM DES PartiesRemarque Avant L’UTILISATION Sac à poussière ou guide-poussière Réglage DE LA Scie Avant L’UTILISATIONVérifier le bon fonctionnement du carter de sécurité 11.Vérifier si la lame est serréeRéglage de la profondeur de coupe Fig Réglage de l’angle d’inclinaisonRéglage du guide garde de refente Procedures DE Coupe Avertissement Montage ET Demontage DE LA Lame DE Scie Démontage de la lame de scie FigMontage de la lame Utilisation DU SAC À Poussière Avertissement Fixation du sac à poussièreUtilisation DU GUIDE-POUSSIÈRE Avertissement Ne jamais transporter l’outil par le guide- poussièreInspection de la lame de scie Remplacement dun balai en carboneEntretien ET Inspection Vérifier les vis de fixationListe des pièces de rechange PrecaucionAccessoires Accessoires StandardInformación Importante Significado DE LAS Palabras DE SeñalizaciónSeguridad Normas DE SeguridadLEA Todas LAS Instrucciones Utilice LA Herramienta Correcta Mantenga a LOS Niños AlejadosNo Fuerce LAS Herramientas 13. Vístase AdecuadamenteManeje Correctamente LA Herramienta Preste AtenciónCompruebe LAS Piezas Dañadas Compruebe LOS Cables ActivosManeje CON Cuidado LAS Herramientas Eléctricas No Limpie LAS Partes DE Plástico CON DisolventeEspañol No Haga Funcionar LA Sierra Mientras LA Lleve Hacia SU Lado ContragolpeServicio Y Reparación Piezas DE ReemplazoEnchufes Polarizados Utilización DE UN Cable Prolongador Aislamiento Doble Para Ofrecer UNA Operación MÁS Segura Especificaciones Descripción FunctionalNomenclatura NotaMontaje Y Operación AplicacionesAntes DE LA Operación Ajuste DE LA Sierra Antes DE Utilizarla Ajuste de la profundidad de corte Fig Ajuste del ángulo de inclinaciónRegulación de la guía Guía de corte Procedimientos DE Corte Advertencia De corte con la cuchilla de la sierra, utilizando laDesmontaje de la cuchilla de la sierra Fig Montaje de la cuchilla de la sierraUSO DE LA Bolsa Para EL Polvo Advertencia USO DE LA Guia Para EL Polvo Advertencia Instalación de la guía para el polvoPRECA1IÓN Comprobación de los tornillos de montaje Mantenimiento E InspecciónInspección de la hoja de sierra Inspección de la escobillas FigLista de repuestos ModificacionesAccesorios Estándar Accesorios OPCIONALES.......de venta por separadoPage Page Español Hitachi Koki Canada Co