Emerson AC4 user manual View Status Options

Page 24

View Status Options

5.0VIEW STATUS OPTIONS

NOTE

For ease of understanding, this section uses the LCD interface to illustrate most instructions, except for features that are available only through the Service Terminal Interface. All Service Terminal Interface screens appear in Appendix A - Service Terminal Interface.

The View Status menu allows any user to view currently active alarms, data stored in the alarm and event logs and the status of all inputs and outputs. The arrows ↑↓ are used to scroll through the menu. The Enter ↵ key is used to select the menu item.

This section presents step-by-step instructions for each of the following options:

•View Active Alarms

•View Alarm Log

•View Event Log

•View Input Status

•View Output Status

Figure 8 shows the main options available from the View Status menu.

Figure 8 Menu overview - View Status menu

Opening Screen

LIEBERT AC4

DD-MON-YY HR:MM:SS

VX.XXX.X

PRESS ↵=STATUS/SETUP

Main Menu

>VIEW STATUS

SYSTEM AND CONTROL

↑↓=NEXT ↵=SELECT

View Status

VIEW ACTIVE ALARMS

VIEW ALARM LOG

VIEW EVENT LOG

VIEW INPUT STATUS

VIEW OUTPUT STATUS

View Active Alarms

View Alarm LogView Status optionsView Event Log

> ACTIVE ALARM 40/40	See	> ALARM RECORD 99/99		See	> EVENT RECORD 99/99	See
DEVICE_1 ALARM	Section	DEVICE_1 ALARM		Section	SYSTEM	Section
CONTACT CLOSED	5.1	CONTACT CLOSED		5.2	USER LOGIN	5.3
		30-JUN-04	09:29:10		19-MAY-04 10:07:00
		NO STANDBY AVAILABLE			DEVICE_1 HW FORCE ON
					CONTACT CLOSED
		29-JUN-04	10:45:00		18-MAY-04 06:47:03
		STNDBY DEVICE FAILED			DEVICE_4 FORCE OFF
					CONTACT OPEN
		29-JUN-04	10:39:00		18-MAY-04 05:22:17
		NO RESTART AVAILABLE			DEVICE_3 AUTO
					CONTACT OPEN
		28-JUN-04	06:54:09		18-MAY-04 04:32:11

View Input Status			View Output Status
INPUT /	STATUS	See	OUTPUT / STATUS
> DEVICE_1	ALARM	Section	> DEVICE_1	ALARM
DEVICE_2	NORMAL	5.4	DEVICE_2	OPERATING
DEVICE_3	NORMAL		DEVICE_3	OPERATING
DEVICE_4	NORMAL		DEVICE_4	OPERATING

See Section 5.5

Liebert® AC4™

18

Image 24

Contents Liebert AC4 Page Table of Contents Setup System Setup Common Alarm 7.5 Setup System Setup Zones Appendix a Service Terminal Interface Setup MenuFigures Methods of Viewing and Configuring the Liebert AC4 Available AlarmsData Logs IntroductionLCD for configuration Outside Enclosure OverviewOperation Typical Configuration Device Liebert ChallengerDevice RS232 LiebertLiebert HimodHimod Controller Board Overview Controller board componentsConnector DIP switchLCD connector 24VAC powerLED Indicators LED indicators summaryOutput LEDs Status LEDs Input LEDs Typical Sequence Installation Considerations InstallationPacking Contents Unpacking and Preliminary InspectionSurface-Mounting the Liebert AC4 Required toolsMounting the Panel Flush-Mounting the Liebert AC4 Connect Power to the Liebert AC4 Electrical connections to panelWiring Specifications Wiring and ConnectionsWiring specifications Connecting Digital Inputs and Outputs Connecting Liebert Precision Cooling UnitsConnecting Digital Inputs Numbering keysConnecting Digital Outputs Setting the Digital Output JumpersDigital output jumper settings Connecting Common Alarm Outputs RS232 ConnectorCommon alarm outputs Serial interface connector RS232/EIA5Overview of Menus Guide to Liebert AC4 functionsOpening Screen Overview Main Menu OverviewLCD Menu Overview View Status Options View Active Alarms Active AlarmsClearing Active Alarms Active AlarmsView Alarm Log Alarm LogAlarm log conditions Alarm LogView Event Log Event LogEvent log conditions Event LogView Input Status Input StatusViewing Additional Input Data Digital input statesView Output Status Output StatusViewing Additional Output Data Digital output statesSilence Alarm & Backup LOG Files Service Terminal Interface Silence Alarm Service Terminal Interface onlyBack Up Log Files Service Terminal Interface only Silence Alarm & Backup Log Files Service Terminal Interface Login LoginSystem and Control Options Valid characters for data entryLogin Screen System & Control menu Clear Alarms&Logs selectedSetup System menu Clear Alarms/Logs menuSetup System Overview Setup System Setup InputsDefine Input as Alarmable or Event Change Label Name of InputDefine Input as Normally Open or Normally Closed Set Up Alarmable Inputs in Latched or Unlatched Mode Set Up Delay TimeDelay Time Latched / UnlatchedSetup System Setup Common Alarm Change to Reset Y or Not Reset NReset Common Alarm Setup System Setup Zones Set Up a ZoneMessage if too few devices entered Message if too many devices enteredSetup System Setup Outputs Define Output as Normally Open or Normally ClosedDefine Operating or Standby Mode Enable or Disable an Output Device in Alarm StatusConfigure Output for Loss of Power Fail-Safe Set ModeSetup System Setup System Info Change PasswordChange the Password Reset Password to the Factory Default AaaaSetup Site ID Setup Site IDSet Date & Time/Automatic Daylight Saving Time Set Date & TimeBackup and Upload Configuration File Back Up the Configuration File Upload the Configuration File Factory Defaults Factory DefaultsFirmware Update Service Terminal Interface only Perform Firmware UPDATE-YESY or NON? N Setup Operation Select Setup OperationSetup Operation Menu Default settings operation featuresTurn Automatic Sequencing On or Off Activate / DeactivateSet Interval & Start Time 1- to 99-Day Interval Set Start Time Hour IntervalTurn Standby Testing On or Off Change Standby TestingSpecify Failed Standby Response Failed Standby responseSpecify Hold Delay Time Hold Delay TimeRestart Delay Time Setup Operation MenuOverride Output Clear Alarms & Logs Clear Active AlarmsClear the Alarm Log Clear the Event LogLiebert AC4 Specifications SpecificationsSpecifications Liebert AC4 Appendix a Service Terminal Interface Comparison of Functions LCD and Service Terminal InterfaceConnecting to the Service Terminal Interface COM1 Port Setup Create a ConnectionSpecify COM Port Connection Properties Setup Ascii SetupSettings tab Ascii Setup buttonConnect to the Service Terminal Interface Click on the file name for example, AC4.htSilence Alarm and Backup Log Files Setup Menu OverviewView Status Overview Main Menu For sample screens, seeView Active Alarms View Active AlarmsView Status Menus Main MenuView Alarm Log View Alarm LogView Event Log View Input StatusView Event Log View Input StatusView Output Status View Output StatusSilence Alarm Section A.5.1 Section A.5.2Back Up Alarm Log File Backup Log Files Alarm Log FileBackup Log Files Event Log File Back Up Event Log FileSetup Menu Login MenuLogin Setup Menu Setup MenuTips on Using the Service Terminal Interface See DescriptionSetup Inputs Setup InputsSetup Common Alarm Setup ZonesSetup Common Alarm Setup ZonesSetup Outputs Setup OutputsSetup System Info Setup System InfoChange Password Setup Site ID Set Date & TimeBackup & Upload Configuration File Backup Backup & Upload Configuration File Upload Factory DefaultsFirmware Update Service Terminal Interface only Firmware UpdateSetup Operation Setup Operation Auto SequencingAuto Sequencing Standby Testing Setup Operation Standby TestingHold Delay Setup Operation Failed StandbySetup Operation Hold Delay Failed StandbyRestart Delay Setup Operation Restart DelayOverride Output Override OutputClear Alarms & Logs Clear Alarms & Logs Clear Active AlarmsClear Alarms & Logs Clear the Alarm Log Clear Alarms & Logs Clear the Event Log Specifications Liebert AC4 Specifications Specifications Liebert AC4 Page Ne t Is tTwor k Care