Delta 28-206, 28-276 instruction manual Assembly Tools Required, Assembly Time Estimate

Page 10

ASSEMBLY

ASSEMBLY TOOLS REQUIRED

13mm Open- End Wrench - 8mm Open-End Wrench - Adjustable Wrench

ASSEMBLY TIME ESTIMATE

Assembly for this machine takes 2 hours or less.

For your own safety, do not connect the machine to the power source until the machine is completely assembled and you read and understand the entire instruction manual.

MODEL 28-206 ENCLOSED STAND ASSEMBLY

1.

Place the stand top (A) Fig. 5 on a flat surface.

2.

Align the two holes in the motor mounting plate (E)

 

Fig. 5 with the two holes (B) in the stand top (A).

3.

Insert the shaft (D) through the holes in the motor

 

mounting plate and the holes in the stand top.

4.

Attach the two "C" rings (C) Fig. 5 on the shaft.

5.

Align the four holes on the motor bracket with the

 

four holes (C) Fig. 6 on the motor mounting plate.

 

NOTE: Confirm that the motor pulley (A) Fig. 6 is

 

mounted on the same side as the belt opening hole

C

E

B

A

D

C

Fig. 5

 

(B).

6.

Insert a round head flange screw (M8 x 1.25 x

 

16mm) through the hole in the motor bracket and

 

the hole in the motor mounting plate.

7.

Thread a hex flange nut (M8x1.25) on the screw.

8.

Repeat this process for the three remaining holes.

C

A

B

Fig. 6

9.Align the holes in the side (A) Fig. 7 with the holes in the stand top (B).

NOTE: Confirm that the hinge catches (C) Fig. 7 are pointed toward the stand top.

10.Insert a hex head flange screw (M8x1.25x16mm) through the hole in the side of the stand and the hole in the top of the stand.

11.Thread a flange nut (M8x1.25)on the screw.

NOTE: Loosely tighten the hardware for further adjustment.

12.Repeat this process for the five remaining holes.

13.Attach the other stand side in the same manner.

A

Fig. 7

C

B

10 - English

Image 10
Contents Contractors Saw Important Safety Instructions Table of ContentsSafety Guidelines Definitions General Safety Rules Stay ALERT, Watch What YOU are DOING, and USEAdditional Specific Safety Rules Refer to them often Use them to instruct othersPower Connections Extension Cords Fig. CCarton Contents Functional DescriptionModel 28-206 Enclosed Stand Parts Model 28-276 Open Stand Parts Assembly Time Estimate AssemblyAssembly Tools Required Model 28-206 Enclosed Stand AssemblyAlign the holes in the base a , with the holes Model 28-276 Open Stand Assembly Page Attaching the Belt to the SAW and Motor Pulley Attaching the SAW to the StandAttaching the Pulley Guards Attaching Blade to the SAW Connecting Motor Cord to Switch AssemblyDisconnect the machine from the power source Table InsertStarting and Stopping the SAW Locking the Switch in the OFF PositionOperation Tilting the TableAdjusting the Table Stop Adjusting Blade TensionVertical Adjustment of the Upper Blade Guide Assembly Tracking the BladeAdjusting the Upper Blade Guides and Blade Support Bearing Adjusting Lower Blade Guides and Blade Support BearingDust Port Changing Blade Speed for Model 28-206 onlyCutting Curves Troubleshooting GuideProbable Cause Remedy Probable Cause RemedyBand SAW Blades Maintenance ServiceWarranty AccessoriesService and Repairs LA Proposition DE Californie LES Instructions Importantes DE SureteMesures DE Sécurité Définitions Conservez CES InstructionsRègles DE Sécurité Générales Lutilisation DE CET OutilRègles Spécifiques Additionnelles DE Sûreté Conserver CES DirectivesSpécifications DU Moteur Raccordements ÉlectriquesInstructions DE Mise À LA Terre Cordon DE Rallonge Fonctionnement Monophasé À 240 VoltsAVANT-PROPOS Contenu DU CartonDésemballage ET Nettoyage Pièces DU Socle Fermé DU Modèle Pièces DU Socle Ouvert DU Modèle Durée Estimée Pour L’ASSEMBLAGE AssemblageOutils Nécessaires Pour L’ASSEMBLAGE Assemblage DU Socle Fermé DU ModèleFrench Assemblage DU Socle Ouvert DU Modèle French Assemblage DE LA Scie SUR LE Socle Assemblage DES Protecteurs DE PoulieAssemblage DE LA Lame SUR LA Scie Connexion DU Cordon Moteur À L’ENSEMBLE DE L’INTERRUPTEURAssemblage DE LA Table SUR LA Scie Insert DE TableVerrouiller L’INTERRUPTEUR EN Position D’ARRÊT FonctionnementDémarrage ET Arrêt DE Scie Inclinaison DE LA TableRéglage DE LA Butée DE LA Table Réglage DE LA Tension DE LameAlignement DE LA Lame Réglage Vertical DE L’ENSEMBLE DE Guide Supérieur DE LA LameDébrancher l’appareil de la source d’alimentation Utilisation DE L’APPAREIL Goulotte À PoussièreCoupe DE Courbes Problème LA Scie NE Démarre PAS Cause probable SolutionGuide DE Dépannage Problème LA Scie À Ruban Vibre Beaucoup Cause probableProblème LES Lames Cassent Cause probable Problème LA Lame NE S’ALIGNE PAS Cause probableGarder LA Machine Propre EntretienLames DE Scie À Lame Ruban Démarrage ImpossibleGarantie AccessoiriesRemplacement Gratuit DE Létiquette Entretien ET RéparationPautas DE SEGURIDAD/DEFINICIONES Instrucciones DE Seguridad ImportantesProposición DE California Normas Generales DE Seguridad EL USO DE Esta HerramientaGuarde Estas Instrucciones Normas Específicas Adicionales DE SeguridadEspecificaciones DEL Motor Conexiones a LA Fuente DE AlimentaciónInstrucciones DE Conexión a Tierra Cordones DE Extensión Fig. D1Prefacio Descripción FuncionalContenido DE Carton Desempaquetado Y LimpiezaPiezas Cerradas DEL Soporte DEL Modelo Base Tornillo de cabeza troncocónica M5 x 0.8 x 10 mm LadoPiezas Abiertas DEL Soporte DEL Modelo Estimación DEL Tiempo DE Ensamblaje EnsamblajeHerramientas DE Ensamblaje Requeridas Montaje DE LA Base DE Soporte Cerrada ModeloNota Apriete libremente el hardware para el ajuste adicional Montaje DE LA Base DE Soporte Abierta Modelo Sobre una superficie planaPage Sujeción DE LA Sierra a LA Base DE Soporte Conectar LA Agujeros DEL Protector DE LA PoleaSujeción DE LA Hoja a LA Sierra Cuerda DEL Motor QUE Conecta a LA Asamblea DE InterruptorSujeción DE LA Mesa a LA Sierra Montaje DE LA Pieza DE Insercion DE MesaBloqueando EL Interruptor EN LA Posicion DE Apagado OperaciónArrancando Y Deteniendo LA Sierra Inclinación DE LA TablaAjuste DE LA Parada DE LA Tabla Ajuste DE LA Tensión DE LA LáminaSeguir LA Lámina Ajuste Vertical DEL Montaje Superior DE LA Guía DE LA LáminaDesconecte la maquina de la fuente de energia Utilizar LA Maquina Puerto DEL PolvoCausa probable Guia Localizacion DE FallasCorte DE Curvas Causa probable RemedioRemedios Localizacion DE Fallas Mantenimiento Hojas DE Sierra DE CintaMantenga LA Máquina Limpia Servicio Accesorios Garantia